How to identify antennas?

Talk about anything and everything here within reason.
User avatar
izeman   10 GW

10 GW
Posts: 4929
Joined: Jun 21 2011 8:25am
Location: vienna, austria
Contact:

How to identify antennas?

Post by izeman » Aug 14 2019 12:01pm

Over the years I bought several antennas from ebay, aliexpress ... Some for 433Mhz projects, some for Wifi (2.4/5.8Ghz). Some for 868Mhz.
Of course after some time, if they where not installed, they ended all in one big box. They are all black or white, but other from that they look more or less the same.
How can i find out what antenna is for what frequency????

markz   100 GW

100 GW
Posts: 7667
Joined: Jan 09 2014 11:38pm
Location: Alberta Canada

Re: How to identify antennas?

Post by markz » Aug 14 2019 8:05pm

No markings at all on the antenna's?

I found this site, basically s.o.l. unless you want to open up the plastic housings.
https://physics.stackexchange.com/quest ... signed-for

User avatar
fechter   100 GW

100 GW
Posts: 14289
Joined: Dec 31 2006 3:23pm
Location: California Bay Area, USA

Re: How to identify antennas?

Post by fechter » Aug 14 2019 9:59pm

If there are no markings, it will be hard to know without using some expensive test equipment or ripping them apart.
"One test is worth a thousand opinions"

mark5   100 kW

100 kW
Posts: 1284
Joined: Dec 28 2011 9:26pm
Location: USA

Re: How to identify antennas?

Post by mark5 » Aug 14 2019 10:44pm

Run them through a security X-ray machine like they have at criminal courts to try to see the antenna element lengths?

billvon   100 MW

100 MW
Posts: 2925
Joined: Sep 16 2007 9:53pm
Location: san diego

Re: How to identify antennas?

Post by billvon » Aug 14 2019 11:06pm

izeman wrote:
Aug 14 2019 12:01pm
How can i find out what antenna is for what frequency????
Borrow a network analyzer and check their S11 across frequencies. You'll see one frequency it is tuned for; it will work best around that frequency.

Alternatively you could do a very manual test with an RF frequency generator, a 50 ohm resistor and a power meter. A spectrum analyzer makes things a little easier.
--bill von

User avatar
amberwolf   100 GW

100 GW
Posts: 27871
Joined: Aug 17 2009 6:43am
Location: Phoenix, AZ, USA, Earth, Sol, Local Bubble, Orion Arm, Milky Way, Local Group
Contact:

Re: How to identify antennas?

Post by amberwolf » Aug 15 2019 3:50am

One basic test is to measure the actual antenna length, and calculate the wavelength that would be for. frequency is just wavelength inverted (1/x, IIRC) so you can see the frequency based on that.

They'll probably be made for some fraction of their actual wavelength. So you can multiply the frequency by some common ones to guess, so let's say they're 1/4 wavelength and measure out to be for 8.4ghz. That means tehy're rpobably for 2.1ghz, at 1/4 wavelength.

YOu won't know if they're 1/4, 1/2, or whatever, but there are common frequency bands so if the measurement comes out for something that's way higher than you'd expect, divide it by various fractions to see if it comes out to a band you recognize.

If you don't understand what I mean, go to some of the ham radio sites and they'll explain antennas/etc well enough to figure it out. (my brain is too tired to be sure I'm making sense).

User avatar
izeman   10 GW

10 GW
Posts: 4929
Joined: Jun 21 2011 8:25am
Location: vienna, austria
Contact:

Re: How to identify antennas?

Post by izeman » Aug 15 2019 5:43am

Damn. I expected those answers, because it googled at bit before.
I don't want (and in some cases even can't) disassemble the antennas. Of course it could just add them to the receiver and see which one works best, but that is a bit to much guess work for me.
I hope the "one or two ring theory" is reliable. As all of the stuff comes from China, I'm not sure they care about this. Take any cover they have and call it a day.
Thanks everybody!!

kcuf   100 W

100 W
Posts: 184
Joined: Sep 29 2018 3:21pm

Re: How to identify antennas?

Post by kcuf » Aug 15 2019 8:34am

best antenna is elevation
In 2013 an ad appears on Russia social networks: Интернет-операторы хотели! Работа в шикарном офисе в Ольгино !!!, зарплата 25960 рублей в месяц

User avatar
izeman   10 GW

10 GW
Posts: 4929
Joined: Jun 21 2011 8:25am
Location: vienna, austria
Contact:

Re: How to identify antennas?

Post by izeman » Aug 15 2019 9:12am

kcuf wrote:
Aug 15 2019 8:34am
best antenna is elevation
Sure. Just tell this to my devices in the basement and I'm fine?? 8) :lol:

kcuf   100 W

100 W
Posts: 184
Joined: Sep 29 2018 3:21pm

Re: How to identify antennas?

Post by kcuf » Aug 15 2019 11:28am

don't talk to devices

put em where they do the most good
In 2013 an ad appears on Russia social networks: Интернет-операторы хотели! Работа в шикарном офисе в Ольгино !!!, зарплата 25960 рублей в месяц

HK12K   100 W

100 W
Posts: 126
Joined: Jul 24 2019 12:49pm

Re: How to identify antennas?

Post by HK12K » Aug 15 2019 1:49pm

If you can find a forum for Ham radio enthusiasts they may be able to identify them just by looking at them.

dustNbone   10 kW

10 kW
Posts: 946
Joined: Mar 13 2016 9:59pm
Location: Vancouver, BC

Re: How to identify antennas?

Post by dustNbone » Aug 15 2019 2:41pm

Yup. What you need is radio nerds. Or enthusiasts.

User avatar
izeman   10 GW

10 GW
Posts: 4929
Joined: Jun 21 2011 8:25am
Location: vienna, austria
Contact:

Re: How to identify antennas?

Post by izeman » Aug 15 2019 3:13pm

kcuf wrote:
Aug 15 2019 11:28am
don't talk to devices
put em where they do the most good
Your help is really appreciated.

User avatar
fechter   100 GW

100 GW
Posts: 14289
Joined: Dec 31 2006 3:23pm
Location: California Bay Area, USA

Re: How to identify antennas?

Post by fechter » Aug 15 2019 3:33pm

Post some pictures.
Also look closely around the end for any markings.
"One test is worth a thousand opinions"

markz   100 GW

100 GW
Posts: 7667
Joined: Jan 09 2014 11:38pm
Location: Alberta Canada

Re: How to identify antennas?

Post by markz » Aug 16 2019 5:17pm

Perhaps find a Ham Radio person in your area, maybe they might be of help.

Look for some Ham Radio forums.

User avatar
izeman   10 GW

10 GW
Posts: 4929
Joined: Jun 21 2011 8:25am
Location: vienna, austria
Contact:

Re: How to identify antennas?

Post by izeman » Aug 17 2019 8:59am

I have some 433 and 2.4 antennas and they look EXACTLY the same. So posting pics will make no sense. 🤮

AngryBob   100 W

100 W
Posts: 127
Joined: Jul 10 2019 4:37pm

Re: How to identify antennas?

Post by AngryBob » Aug 17 2019 10:41am

I realize the trial and error method is not as attractive, but what that will do, is tell you which antenna ACTUALLY WORKS BETTER, rather than a somewhat theoretical view of which one SHOULD.

User avatar
marty   10 MW

10 MW
Posts: 2220
Joined: Apr 19 2007 5:44pm
Location: Buffalo, New York USA
Contact:

Re: How to identify antennas?

Post by marty » Aug 17 2019 7:17pm

AngryBob wrote:
Aug 17 2019 10:41am
I realize the trial and error method is not as attractive, but what that will do, is tell you which antenna ACTUALLY WORKS BETTER, rather than a somewhat theoretical view of which one SHOULD.
My $20 TV antenna from Radio Shack don't work much better then the piece of wire with alligator clips that I used to have. On my list of things to do is a big TV antenna on the roof. And another internet receiving antenna like this.
Image

That's the internet receiving antenna at mt shop. [Works Great] Want to do the same thing at my house.
MARTY
Volt Electric Vehicles
http://www.voltev.com

User avatar
fechter   100 GW

100 GW
Posts: 14289
Joined: Dec 31 2006 3:23pm
Location: California Bay Area, USA

Re: How to identify antennas?

Post by fechter » Aug 19 2019 11:08am

Just curious what you used the 433mhz antenna for?

I agree a ham radio operator or anyone in the mobile radio business might have test equipment that would identify the frequency.
"One test is worth a thousand opinions"

User avatar
izeman   10 GW

10 GW
Posts: 4929
Joined: Jun 21 2011 8:25am
Location: vienna, austria
Contact:

Re: How to identify antennas?

Post by izeman » Aug 19 2019 11:40am

433 was used for home automation sensors. I switched to zigbee mostly now - so i need 2.4ghz antennas to replace the pcb printed ones (for those cases where more range is needed).

User avatar
fechter   100 GW

100 GW
Posts: 14289
Joined: Dec 31 2006 3:23pm
Location: California Bay Area, USA

Re: How to identify antennas?

Post by fechter » Aug 19 2019 11:35pm

If you have a set that works you could range test the various antennas. The one with the longest range will be the one for that frequency.

I was pretty impressed with the range on my 433mHz remote switches.
"One test is worth a thousand opinions"

User avatar
izeman   10 GW

10 GW
Posts: 4929
Joined: Jun 21 2011 8:25am
Location: vienna, austria
Contact:

Re: How to identify antennas?

Post by izeman » Aug 20 2019 4:56am

fechter wrote:
Aug 19 2019 11:35pm
If you have a set that works you could range test the various antennas. The one with the longest range will be the one for that frequency.

I was pretty impressed with the range on my 433mHz remote switches.
That was the only approach that makes sense in my case. And is the way i do it now. I was hoping for a more 'engineer like' way. :lol: 8)

User avatar
fechter   100 GW

100 GW
Posts: 14289
Joined: Dec 31 2006 3:23pm
Location: California Bay Area, USA

Re: How to identify antennas?

Post by fechter » Aug 20 2019 11:34am

izeman wrote:
Aug 20 2019 4:56am

That was the only approach that makes sense in my case. And is the way i do it now. I was hoping for a more 'engineer like' way. :lol: 8)
Something like a SWR analyzer or spectrum analyzer would be the preferred engineer approach. Those machines are very expensive so hard to find somebody that has one. Beside ham operators, people who service radio equipment would have them.
"One test is worth a thousand opinions"

markz   100 GW

100 GW
Posts: 7667
Joined: Jan 09 2014 11:38pm
Location: Alberta Canada

Re: How to identify antennas?

Post by markz » Aug 20 2019 7:00pm

Yes, those very well may be able to help, not many around anymore.

Not even electronics repair places neither but they probably don't have the equipment.

Think of what people use antenna's a lot, and would have the equipment.
Ham Radio
Radio Repair
Cell Phone Technician
Router Technician
Universities/Colleges/Technical Schools (Maybe put up a poster on campus)
CB Radio Technician Repair




people who service radio equipment would have them.

User avatar
parajared   10 kW

10 kW
Posts: 849
Joined: Apr 16 2012 11:33pm
Location: Northern Arizona

Re: How to identify antennas?

Post by parajared » Aug 22 2019 3:32pm

Presumably you just try them out and see what works best and this is because of impedance. Even among the same manufacturer antenna length varies and that's because loads are different from device to device. The materials used cause resistance and the antenna/device has to match.

For instance when you are building a 433mhz antenna you could broadly say that your antenna would be 70cm for a full wave, 35cm for half wave ect... but in reality you just build your antenna too long and hook it up to a SWR meter. You chop of a little bit of material at a time, annotate your SWR readings, then rebuild.
example
SWR at 40cm = 12
SWR at 38cm = 9
SWR at 35cm = 2
SWR at 33cm = 1.5
SWR at 30cm = 2
SWR at 28cm = 4

You would (in this particular example) re-build your home brew 433 antenna to ~33cm for that exact device because that's the best reading you could get. Your device and antenna have to match. Hope this helps.

Post Reply