opening a Bafang CST... and putting it back!

Get all your technical information about electric bikes here.
Post Reply
quamau
100 mW
100 mW
Posts: 41
Joined: Jan 09, 2009 4:35 pm

opening a Bafang CST... and putting it back!

Post by quamau » Dec 30, 2017 6:34 pm

Hi there,

I need help with a Bafang CST which I just opened to substitute the nylon gears. After opening, and learning that the motor was in perfect condition but for one split gear and another one with a damaged teeth, I ordered replacement gears, swapped them, mounted everything back, and... I have got a problem.

After screwing down the plate, the wheel does not spin freely. To give you an idea, the forward drag is comparable (if not a tad higher) that the drag I get when I counter-rotate the wheel, which engages the motor.

The fact that this drag appears only when the cover plate is screwed down fully makes me think that I made a mistake with shims or washers. Unfortunately I did not take pictures while opening...

Is there anybody out there that could tutor me in making sure that everything has been mounted correctly?

Thanks in advance for your time

User avatar
motomech
100 MW
100 MW
Posts: 2908
Joined: Sep 11, 2010 12:21 am
Location: Tucson Az.

Re: opening a Bafang CST... and putting it back!

Post by motomech » Dec 30, 2017 7:15 pm

Did you count the number of teeth on the replacement gears? I believe the gear ratios are particular to the CST and the gears from the other BPM's will not work.
Motomech

'03 Rocky Mountain Edge 2WD 260 Q100H frt and Ezee V1 rear 2 Elifebike 20A & 25A 9-FET controllers 12S/20Ah Multistar Lipo rear 5Ah Turnigy frt Luna Cyclops Extra lite Alex 24DM rims, 2.4 Holly Rollers run ghetto tubeless. 25 mph. Mean Well HLG-320H-48A
https://endless-sphere.com/forums/viewt ... =3&t=83430
'07 GT Idive 4 4.0, Q100C 201 12S LiPoly elifebike 9-FET 17A controller. 20 MPH.
https://endless-sphere.com/forums/viewt ... 8#p1237928

User avatar
fechter
100 GW
100 GW
Posts: 11971
Joined: Dec 31, 2006 3:23 pm
Location: California Bay Area, USA

Re: opening a Bafang CST... and putting it back!

Post by fechter » Dec 30, 2017 7:36 pm

I think you'll have to take it apart again and look for where it's rubbing and look for spacers, washers, etc. that might go in a different spot.
"One test is worth a thousand opinions"

quamau
100 mW
100 mW
Posts: 41
Joined: Jan 09, 2009 4:35 pm

Re: opening a Bafang CST... and putting it back!

Post by quamau » Dec 31, 2017 4:49 am

Number of teeth is OK: I believe it's 42, anyway everything runs very smoothly once the motor is disassembled, or until the cap not not tightened.

Opening it up again... it's obviously what I have to do, and I did it already. However, there is not much to misplace that I don't know what to change. There is no visible wear, but I did not run the bike on the road yet, only a little of hand spinning.

User avatar
fechter
100 GW
100 GW
Posts: 11971
Joined: Dec 31, 2006 3:23 pm
Location: California Bay Area, USA

Re: opening a Bafang CST... and putting it back!

Post by fechter » Dec 31, 2017 12:03 pm

Sometimes a bearing can shift a little when pulling things apart and may need some force to get back in place. Like squeeze the housing around the axle to make sure the bearings are fully seated.
"One test is worth a thousand opinions"

quamau
100 mW
100 mW
Posts: 41
Joined: Jan 09, 2009 4:35 pm

Re: opening a Bafang CST... and putting it back!

Post by quamau » Jan 01, 2018 6:56 am

Thank you fecther, this is a thoughtful suggestion, I will take it apart once more with your words in mind.

Post Reply