Crystalyte 5404 / 5403 UPGRADED! LAST CALL

[amberwolf]

Also has anyone else experience spoke breakage? I seem to break spokes very frequently and wonder if it is because they are too hard.

If they are not tensioned correctly, too loose, then they will break easier as they are flexed more. If they are too tight, then they can't flex at all, and will break. If the wheel experiences lots of side loads, and tension is wrong, the rim itself will distort and bend, permanently altering the tension, making some too tight and some far too loose, and they'll just start snapping in droves.

[Handyhappy1]

Thank you for the quick response to my questions. Just a thought...I do see other people with 5300 and even hs series motors running high wattage using higher voltage than I am currently using. Is the amperage the breaking point on these motors? I really enjoy high acceleration and although my 75kmh is not quite what others are doing on this forum it is still fast enough for me.
I was thinking that the wider Alex dx32 rim would help as far as spoke breaking. This would distribute some of the side forces over a wider area and help to eliminate or reduce spoke breakage. Comments again are appreciated.

[Hobbit]

So a couple of lads (one named hobbit) from the shire, travel across (middle)earth to retrieve the rings of power.

[methods]

That's a really bromantic picture


-methods

[Tincan]

I was more thinking a scene from "Road Trip"

[Hyena]

T minus 3 hours until Hobbit and I roll into Mordor.
Lets put a lid on this saga!

Now, who wanted large screen CA's to go with these ? I remember a few people asking me a while back and I think I put most of you on hold with a "remind me when the motors come in"

[Tincan]

but i have already wired in my normal ca............

[Hobbit]

Got mine! And everyone else's in Australia for about an hour there. thanks, indescribable gratitude to Hyena, maxwell,wojtek and basically everyone involved. When I ride my own electric vehicle off into the sunset for the first time, I reckon I'll have tears of joy going on. It's going to be a very sacred thing.

[jonescg]

8 months, 637 posts and 22,000 views, you finally got your motors

Don't frock em up

[Hyena]

Got mine! And everyone else's in Australia for about an hour there.

Yes that did occur to me as you drove off with 15 grands worth of stuff...
Speaking of which this is Hobbit's van jammed to the eyeballs with all our gear. Talk about a perfect fit, we couldn't have fitted a single extra box!

hobbit-van.jpg (99.91 KiB) Viewed 484 times

with thanks, indescribable gratitude to Hyena, maxwell,wojtek and basically everyone involved.

And on behalf of all the other Aussies thanks for your time and services today in collecting the gear, that saved everyone a few dollars in local delivery fees from the dock.
For a while there I thought I was going to die of cancer before Kenny made and delivered these motors but we got there in the end!

Pron:

crystalyte pron.jpg (206.1 KiB) Viewed 484 times

Now, the slightly bad news.
Costs did go a little over budget for a number of reasons - luck wasn't on our side when the day came to actually pay for the motors, after hoving around 1:1 and slightly better than the USD for quite a while the AUD took a bit of a plunge to around 95c USD. It has since bounced back but that doesn't help us as the transaction was completed when it was lower. That added $15-20 to the cost in AUD, then there was the duty, hefty GST etc etc. I allowed for most of it in my estimate and even a little over and in the end it was only the currency fluctuation that caught me out. So, bottom line is the motors, landed in my lap ended up costing $10 each more than planned. I did say up front that the quoted price (that everyone paid) was only an estimate so hopefully everyone is cool with this. All told I think it actually came extremely close considering we're taking fees and charges in the viscinity of 3 grand.
So yeah, I'll add that $10 in with the postage when everyone is finalising payment.
On that note, as you can see above I have a considerable number of these to shift so if you're in Sydney local pickup would be preferred.
I will be using interparcel.com.au to ship these out, I've used them before and find their rates reasonable. However if you'd like to make your own courier arrangements then I'm more than happy for you to do this. Likewise if you happen to have a commercial account we can get better rates on then let me know! Unfortunately Auspost won't ship boxes this big.
The boxes are is 69x68x26cm and weighs about 15kg (I think that was what others had found, right ? I haven't got a hugely accurate scale here) and are leaving from 2232
As an estimate, postage to Melbourne and Brisbane is around $30, Perth is... better sit down... $70. Ouch

[optimus prime voice] 5404s, roll out! [/voice]

[methods]

Now, who wanted large screen CA's to go with these ? I remember a few people asking me a while back and I think I put most of you on hold with a "remind me when the motors come in"

His are counterfeit Canadian knock-off's of the real Chinese ones I sell. Mine dont read Ah - but they look cool - and they have lots of buttons.

-methods

[Tincan]

Hyena, hit me with some payment details and I'll send you some dollars!

[Hyena]

haha Methods and his crystalyte Anal Probe Meters (APM for short)

Tincan email or PM me your address and I'll get you a shipping price.

Also, first stuff up of the order noted: Kenny has ripped me off for a HI4080. According to the packing list the box was supposed to have 2 motors in it, a 60 and 80. But there's only one motor in it. So not only am I short a motor but I paid duty and tax on it too, under the assumption that it was included

[chroot]

Oh that's freaking up! What are you gonna do with Kenny being habit rip everyone off and his word shall never trusted.

haha Methods and his crystalyte Anal Probe Meters (APM for short)

Also, first stuff up of the order noted: Kenny has ripped me off for a HI4080. According to the packing list the box was supposed to have 2 motors in it, a 60 and 80. But there's only one motor in it. So not only am I short a motor but I paid duty and tax on it too, under the assumption that it was included

[methods]

Would someone please hurry up and photoshop this picture?



-methods

[neptronix]

Is Kenny disputing that he sent you 1 motor instead of 2, or was it just a mistake?

It's important to know the difference.

[Rustedhen]

Picked up my motors from Hyena yesterday.

Haven't had time to play with them yet but thanks to everyone involved in getting these into our hands.

[Willow]

frock up.

Upfrock.jpg (245.94 KiB) Viewed 340 times

[Tincan]

[Nanoha]

LOL!!!

Thanks to Hyena and everyone involved to make this happen!
I finally have my 200W big dick motor...

[methods]

[Willow]

would you like cracked pepper with that??

[methods]

would you like cracked pepper with that??

You must be going to nice restaurants... where I can afford to eat they only ask "for here or to go?"

I love that photo shop... someone please make it better.

-methods

[Tincan]

Time to "rock out" with ya.......

[Willow]

...frock out.