Phasor Cycles Electric Mountain Bike Frame Pre-order

[ohzee]

I bought some bb7's for my yuba mundo and they stop me on a dime.. I installed them myself and it was quite easy.

teklektik made a great post about installing them on the yuba , but you can get the idea how easy it is by watching.

http://endless-sphere.com/forums/viewto ... =2&t=37560

I did get the larger size brake for front/back and I think that makes a difference for anything fast.

I will probably go the same route my phasor as I am very impressed with their stopping ability even from 30mph.

[Rodney64]

Just purchased a h3580 motor. I'm going for speed. I ended up buying the fox rear shock RC4 for 350 off eBay.

[jonescg]

Speed means Volts. And lots of them

[Rodney64]

Chris, Matt has purchased the motor not sure about the controller but it will be 72 volt. So it battery time now. So ready for your expertise.

[Trackman417]

I bought some bb7's for my yuba mundo and they stop me on a dime.. I installed them myself and it was quite easy.

teklektik made a great post about installing them on the yuba , but you can get the idea how easy it is by watching.

viewtopic.php?f=2&t=37560

I did get the larger size brake for front/back and I think that makes a difference for anything fast.

I will probably go the same route my phasor as I am very impressed with their stopping ability even from 30mph.

BB7's are the greatest mechanical brakes! Jut got them installed yesterday to replace my front brake. These things are powerful! I feel like if I pull hard enough on the lever they will launch me over the handle bars I never used hi quality disk brakes before and these are it!

Just purchased a h3580 motor. I'm going for speed. I ended up buying the fox rear shock RC4 for 350 off eBay.

Where did you get the H3580 motor? If you don't mind my asking. I have been looking all over for it. And the only people who seem to be selling are HPC and they are overpricing it to $650 .

[Rodney64]

A guy here in Perth. He got 2 one for himself and one for me. At first we were going to get the HS4080 but it's only a single speed. I can ask Matt and see if he's prepared to get you one. These are the first he's imported

[Trackman417]

A guy here in Perth. He got 2 one for himself and one for me. At first we were going to get the HS4080 but it's only a single speed. I can ask Matt and see if he's prepared to get you one. These are the first he's imported

PM sent. Don't want to spam this thread with anything not Phasor cycle related

[dpearce]

[Rodney64]

That's amazing David. Can't wait.

[competitions]

Mad skills at 1:50

Well done!

[Rodney64]

Purchased all my components in black. I think I will go with a white frame.

[nicobie]

I asked them if their frame drop outs could handle a 150mm Cormotor but got No response.

[ohzee]

My 5404 is 150mm so I hope so as well. If not I will do whatever is needed to make it fit.

[nicobie]

Is this frame vaporware?

[briangv99]

Is this frame vaporware?

no, has taken a while but production has kicked off now

looking forward to receiving mine, I hope in June

http://endless-sphere.com/forums/viewtopic.php?f=15&t=32950&start=195

[nicobie]

Is this frame vaporware?

no, has taken a while but production has kicked off now

looking forward to receiving mine, I hope in June

http://endless-sphere.com/forums/viewtopic.php?f=15&t=32950&start=195

\


I guess it only fits the BMC motors then..

What a shame.

[briangv99]

I guess it only fits the BMC motors then..

What a shame.

I don't think so. I don't know the dropout spacing on the prototype for certain, but it will fit any hub designed to fit a 135mm dropout. I'm sure there's space for the Phasor guys to weld on the dropouts at a slightly wider spacing on request.

[ohzee]

So how we looking on putting these together ? hopefully you have the cnc'd stuff you were waiting for.
Id imagine it should be about shipping out time for the first one ?

Hope it's moving along update would be nice. Thanks

[nicobie]

So how we looking on putting these together ? hopefully you have the cnc'd stuff you were waiting for.
Id imagine it should be about shipping out time for the first one ?

Hope it's moving along update would be nice. Thanks

Yes, I'm interested in a update too.

I have tried emailing them but haven't gotten any replys yet.

It's kind of a shame because I was wanting to give them $.

It's beginning to look like they got in a little too deep.......

[ohzee]

So by now id hope you had your 1st bike shipped - is that the case ?

I think you have updated your other thread since this one. I was just wanting to see how it was going.

Hopefully well.. Any luck offloading some of the CNC work ?

[Deutch420]

My frame is ready, i cant wait!!

[Rodney64]

My frame is ready, i cant wait!!

Lucky man. Cant wait for mine too.

[SweKen]

I cant decide what color i want.. We should choose different colors so that we can tell each other apart, that would have been great!

[Rodney64]

I cant decide what color i want.. We should choose different colors so that we can tell each other apart, that would have been great!

I went candy blue, perhaps a colour which goes well with snow.

[ohzee]

Mine is done as well it's a forest green metallic called tucker green. Should ship out soon id imagine.

The build is going to be slow , but when I get it ill get some good pics of batteries/controllers inside
the frame as that's something I know I want to see badly.

Great job Phasor nice to see your hard work paying off.