EF X2

Hi,

My new design of electric Longboard EF X2
The concept applies mainly motorholder to be compatible with the Truck Caliber II.

Material - powder coated steel and stainless steel (cheap and durable).
MotorHolder in the form of a rigid closed frame.

Version 1:
Inside is housed one engine and the electronics, ie. The ESC, switch, battery charge indicator.
Version 2:
Inside the 2 engines 6354 or shorter.



The second element of the design is the battery box. The box is to enable the rapid exchange of packets (still in development).

love your idea to put the esc/vesc etc in the 2nd motor place !
Thinking about this to, but your all mount enclosure protection it's pefect !!

Good work, good continuation man

nice.
What is the 3d software used to create these pictures ?

Solidworks

The first prototype.
I have to do the electronics housing to protect it against water and dust.

Idea said:

Solidworks

Click to expand...

ok thanks

Hi,
that looks really amazing. I really like the design. May i ask where you got this display from?

I bought on eBay

http://www.ebay.com/sch/i.html?_fro...3.TR0.TRC0.H0.XTF01N.TRS0&_nkw=TF01N&_sacat=0

so cool !! Love it !!!
Great works once again !
soon in test ??!

that's really some impressive SW skills ! I wish I could do the same

Looks like the same meter but is rated up to 80V and is $19.
http://www.ebay.com/itm/131630345531?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT

Nice, really clever use of the space

Cheap option is the use of LiPo batteries.
Below is shown on the pictures koncepcja4 housings for 8 packages 5Ah Turnigy 3S, for a total of 20Ah / 6S
And so it established economic version of the long spacer
A range of about 40km (~ 25 miles)

I present the last version Lingboard with electric drive, a simple construction without a BMS, using conventional LiPo batteries.


My English is poor, so I'll write a little, but instead will be a lot of pictures.

Components:
- DECK Globe - The Maiden
- Turnigy G160 245kV
- ESC FVT 120A 6S
- ZIPPY Flightmax 8Ah 6S (2x8Ah 3S)
- TRUCK - Caliber 2 44
- ABEC 11 Flywheels 83mm
- Remote Controller 2.4 Ghz nano

Technical parameters:
The maximum speed of 36km/h
Range up to 22km

MotorHolder made of stainless steel and PETG
Enclosure Lipo is printed with the PLA
Pulleys made from ABS+ on a 3D printer





MotorHolder apart from the motor also includes ESC, the receiver RC and switch


However, you can mount a large motor such as SK3 6374

Or two smaller ones such as SK3 6354


I did also versions of the motor holder for Paris180



Transmission belt HTD5M has a ratio of 15/36

Pulleys printed on a 3D printer with ABS
I produce pulleys for ABEC 11 Flywheels and Kegel Orangatang





Enclosure Lipo is printed with the PLA it contains LiPo ZIPPY Flightmax 2x8Ah 3S and capacity indicator



Sorry for my english if something is not understandable :?

Nice design idea, however I would not recommend putting the esc close to your bldc motor unless you shield the circuitry very well.
The electromagnetic field around your motor can easily disrupt your esc causing weak or unstable signal if you have the receiver nearby as well. It can also cause random logic problems on the cpu as well as on the memory. You can fix this if you properly shield it though.

WTech said:

Nice design idea, however I would not recommend putting the esc close to your bldc motor unless you shield the circuitry very well.
The electromagnetic field around your motor can easily disrupt your esc causing weak or unstable signal if you have the receiver nearby as well. It can also cause random logic problems on the cpu as well as on the memory. You can fix this if you properly shield it though.

Click to expand...

It's logical what you write, but I have not noticed problems with the receiver and the ESC, and not only for himself made this motor holder.

Motor holder before assembly


and assembled