Your Creation's Before & After Pics

Show off your E-bike creation here.
User avatar
eCue
100 W
100 W
Posts: 114
Joined: Nov 03, 2017 5:14 pm
Location: Vancouver Island , Canada

Re: Your Creation's Before & After Pics

Post by eCue » Dec 06, 2017 10:16 am

Would be a great friction drive bike ..
"98 Quintana roo Panamint 350w mxus build link - https://endless-sphere.com/forums/view ... =6&t=91627

Robert62
1 µW
1 µW
Posts: 2
Joined: Dec 05, 2017 8:44 pm

Re: Your Creation's Before & After Pics

Post by Robert62 » Dec 06, 2017 9:35 pm

SlowCo wrote:
Dec 06, 2017 9:04 am
:lol: 8)

Please also make a wide front fork and insert the same wheel in there as is in the rear and then mount a Cyclone 3000W middrive to the chain drive!
Funny you should mention that. I had the same thought....
Robert

SlowCo
10 kW
10 kW
Posts: 582
Joined: Jan 05, 2015 5:43 pm
Location: The Netherlands

Re: Your Creation's Before & After Pics

Post by SlowCo » Dec 07, 2017 5:40 am

Go for it!
I'm subscribed to this thread so will hopefully see that result in the near future. Or start a built thread for it on E-S and leave a link to it here. :)

electronicru
1 µW
1 µW
Posts: 2
Joined: Nov 19, 2017 4:31 am

Re: Your Creation's Before & After Pics

Post by electronicru » Dec 08, 2017 8:47 am

left (before), right (after)
it was ... 1500W speed 45 km/h
has become ... 8000W speed 70km/h
Attachments
before and after_.jpg

SlowCo
10 kW
10 kW
Posts: 582
Joined: Jan 05, 2015 5:43 pm
Location: The Netherlands

Re: Your Creation's Before & After Pics

Post by SlowCo » Dec 09, 2017 6:23 pm

electronicru wrote: left (before), right (after)
it was ... 1500W speed 45 km/h
has become ... 8000W speed 70km/h
Very nice! 8)
Please tell us more: Which motor, controller, battery etc?

electronicru
1 µW
1 µW
Posts: 2
Joined: Nov 19, 2017 4:31 am

Re: Your Creation's Before & After Pics

Post by electronicru » Dec 10, 2017 1:02 pm

stock motor + “chupasos” :D (forced air cooling)
https://youtu.be/-ee1mJnZ71k
Battery
https://youtu.be/pjHiYKFRZ-o
Stock Controller. Upgrade mosfets, capacitors + forced air cooling + arduino

SlowCo
10 kW
10 kW
Posts: 582
Joined: Jan 05, 2015 5:43 pm
Location: The Netherlands

Re: Your Creation's Before & After Pics

Post by SlowCo » Dec 10, 2017 1:48 pm

Very good result!

User avatar
eCue
100 W
100 W
Posts: 114
Joined: Nov 03, 2017 5:14 pm
Location: Vancouver Island , Canada

Re: Your Creation's Before & After Pics

Post by eCue » Dec 10, 2017 3:54 pm

Friction drive ?

Image

All the comforts of a car without the comfort !
"98 Quintana roo Panamint 350w mxus build link - https://endless-sphere.com/forums/view ... =6&t=91627

Buk___
100 W
100 W
Posts: 211
Joined: Jul 28, 2017 5:59 pm

Re: Your Creation's Before & After Pics

Post by Buk___ » Dec 10, 2017 4:43 pm

eCue wrote:
Dec 10, 2017 3:54 pm
Friction drive ?
Does it rub you the wrong way :)

User avatar
eCue
100 W
100 W
Posts: 114
Joined: Nov 03, 2017 5:14 pm
Location: Vancouver Island , Canada

Re: Your Creation's Before & After Pics

Post by eCue » Dec 11, 2017 12:25 pm

The aero is kinda of upsetting :D but the sunroof makes up for it notice the spoiler :D now if it only had a nose cone ! .. :pancake:
"98 Quintana roo Panamint 350w mxus build link - https://endless-sphere.com/forums/view ... =6&t=91627

webpablo
1 µW
1 µW
Posts: 1
Joined: Dec 11, 2017 4:32 pm

Re: Your Creation's Before & After Pics

Post by webpablo » Dec 11, 2017 4:59 pm

I wanted a commuter that would handle my 6 mile commute in Seattle. This is what I landed on…
Before was a brand new Raleigh Clubman Steel Framed Disc brake Road Bike.
raleigh-clubman-277677-1.jpg
raleigh-clubman-277677-1.jpg (83.01 KiB) Viewed 107 times
After: Bafang BBS02 install
IMG_0096.jpg
The install shop (alki Bike and Board in Seattle, WA) setup a nice little bar end for throttle + controller
I wired in a SuperNova E3 headlight and taillight(not pictured) wired directly to the BBS02's headlight connector.
IMG_0097.jpg
Since I didn't want to give up a brake cut off or my STI shifters, I ordered these and had the shop install them. The used a U-brake noodle to make the angle work on the rear disc brake.
https://em3ev.com/shop/hwbs-ebrake-sensor/
IMG_0098.jpg

User avatar
motomech
100 MW
100 MW
Posts: 2880
Joined: Sep 11, 2010 12:21 am
Location: Tucson Az.

Re: Your Creation's Before & After Pics

Post by motomech » Dec 11, 2017 6:24 pm

electronicru wrote:
Dec 10, 2017 1:02 pm
stock motor + “chupasos” :D (forced air cooling)
https://youtu.be/-ee1mJnZ71k
Battery
https://youtu.be/pjHiYKFRZ-o
Stock Controller. Upgrade mosfets, capacitors + forced air cooling + arduino
“chupasos” = Suckers :D
Motomech

'03 Rocky Mountain Edge 2WD 260 Q100H frt and Ezee V1 rear 2 Elifebike 20A & 25A 9-FET controllers 12S/20Ah Multistar Lipo rear 5Ah Turnigy frt Luna Cyclops Extra lite Alex 24DM rims, 2.4 Holly Rollers run ghetto tubeless. 25 mph. Mean Well HLG-320H-48A
https://endless-sphere.com/forums/viewt ... =3&t=83430
'07 GT Idive 4 4.0, Q100C 201 12S LiPoly elifebike 9-FET 17A controller. 20 MPH.
https://endless-sphere.com/forums/viewt ... 8#p1237928

imagineaudio
100 µW
100 µW
Posts: 9
Joined: Aug 04, 2016 4:16 pm
Location: Los Angeles, CA

Re: Your Creation's Before & After Pics

Post by imagineaudio » Dec 14, 2017 9:03 pm

webpablo wrote:
Dec 11, 2017 4:59 pm
I wanted a commuter that would handle my 6 mile commute in Seattle. This is what I landed on…
Before was a brand new Raleigh Clubman Steel Framed Disc brake Road Bike.
raleigh-clubman-277677-1.jpg

After: Bafang BBS02 install
IMG_0096.jpg

The install shop (alki Bike and Board in Seattle, WA) setup a nice little bar end for throttle + controller
I wired in a SuperNova E3 headlight and taillight(not pictured) wired directly to the BBS02's headlight connector.
IMG_0097.jpg

Since I didn't want to give up a brake cut off or my STI shifters, I ordered these and had the shop install them. The used a U-brake noodle to make the angle work on the rear disc brake.
https://em3ev.com/shop/hwbs-ebrake-sensor/
IMG_0098.jpg

How is that bag mounted to the frame?

Post Reply