hi i have an e-quad with 24v, now i want to upgrade to 36v (12v x 3 (12ah batts)) with speed controller 36v 500w and 350w motor
Should i use 30amp cables to batteries, awg14, 2.5mm2? pvc or silicon type?
thanks in advance.
What cable size for 36v 12ah 500w setup?
5 posts
• Page 1 of 1
What cable size for 36v 12ah 500w setup?
by mikeswrx02 » Fri Feb 11, 2011 5:04 am
- mikeswrx02
- 10 µW
- Posts: 5
- Joined: Thu Feb 10, 2011 6:06 am
Re: What cable size for 36v 12ah 500w setup?
by neptronix » Fri Feb 11, 2011 5:23 am
The most important number is how many amps your controller is rated at. You need to take that peak number and wire under the assumption that the power will be peaking.
If you're running 30amps only for a foot or two, 12ga would be appropriate with minimal drop in voltage. 14 would be stretching it, and 10ga would be ideal.. anything above that is kinda overkill.
I don't think the coating on the wires matters so much. What's inside does though.. copper is more conductive and won't fray.
If you're running 30amps only for a foot or two, 12ga would be appropriate with minimal drop in voltage. 14 would be stretching it, and 10ga would be ideal.. anything above that is kinda overkill.
I don't think the coating on the wires matters so much. What's inside does though.. copper is more conductive and won't fray.
ES facebook group: http://facebook.com/#!/home.php?sk=group_125035107565566&ap=1
The all-arounder: 8T MAC motor on a Trek 4500.
The girlfriend bike: 350W front MAC on a 700c Trek.
The wheelie machine: 20" Rear Magic Pie II on a Trek 4300 MTB
The Bus: ??? on a 'da bomb' cargo bike frame
Pro-tips for noobs: Avoid BMS Battery like the plague | Charge RC Lipos to 4.15v, stop discharging at 3.5-3.6v | Use torque plates/arms! | Rear mounted hubs are always best
The all-arounder: 8T MAC motor on a Trek 4500.
The girlfriend bike: 350W front MAC on a 700c Trek.
The wheelie machine: 20" Rear Magic Pie II on a Trek 4300 MTB
The Bus: ??? on a 'da bomb' cargo bike frame
Pro-tips for noobs: Avoid BMS Battery like the plague | Charge RC Lipos to 4.15v, stop discharging at 3.5-3.6v | Use torque plates/arms! | Rear mounted hubs are always best
-
neptronix - 100 GW
- Posts: 10251
- Joined: Tue Jun 15, 2010 5:56 pm
- Location: Salt Lake City, Utah
Re: What cable size for 36v 12ah 500w setup?
by mikeswrx02 » Fri Feb 11, 2011 5:51 am
neptronix wrote:The most important number is how many amps your controller is rated at. You need to take that peak number and wire under the assumption that the power will be peaking.
If you're running 30amps only for a foot or two, 12ga would be appropriate with minimal drop in voltage. 14 would be stretching it, and 10ga would be ideal.. anything above that is kinda overkill.
I don't think the coating on the wires matters so much. What's inside does though.. copper is more conductive and won't fray.
thank u for your reply.
well my controller does not specify how many amps!
is there a way to measure it?
ok 10ga to be on the safe side
- mikeswrx02
- 10 µW
- Posts: 5
- Joined: Thu Feb 10, 2011 6:06 am
Re: What cable size for 36v 12ah 500w setup?
by neptronix » Fri Feb 11, 2011 6:36 am
usually there is a label on it... if it is a cheap brushed controller and it doesn't have a label, the only way to find out would be something like a watts-up, cycle analyst, or turnigy watt meter.
http://www.hobbycity.com/hobbycity/store/uh_viewitem.asp?idproduct=10080
Which, if you're into eBiking, you should have in your arsenal
http://www.hobbycity.com/hobbycity/store/uh_viewitem.asp?idproduct=10080
Which, if you're into eBiking, you should have in your arsenal
ES facebook group: http://facebook.com/#!/home.php?sk=group_125035107565566&ap=1
The all-arounder: 8T MAC motor on a Trek 4500.
The girlfriend bike: 350W front MAC on a 700c Trek.
The wheelie machine: 20" Rear Magic Pie II on a Trek 4300 MTB
The Bus: ??? on a 'da bomb' cargo bike frame
Pro-tips for noobs: Avoid BMS Battery like the plague | Charge RC Lipos to 4.15v, stop discharging at 3.5-3.6v | Use torque plates/arms! | Rear mounted hubs are always best
The all-arounder: 8T MAC motor on a Trek 4500.
The girlfriend bike: 350W front MAC on a 700c Trek.
The wheelie machine: 20" Rear Magic Pie II on a Trek 4300 MTB
The Bus: ??? on a 'da bomb' cargo bike frame
Pro-tips for noobs: Avoid BMS Battery like the plague | Charge RC Lipos to 4.15v, stop discharging at 3.5-3.6v | Use torque plates/arms! | Rear mounted hubs are always best
-
neptronix - 100 GW
- Posts: 10251
- Joined: Tue Jun 15, 2010 5:56 pm
- Location: Salt Lake City, Utah
Re: What cable size for 36v 12ah 500w setup?
by mikeswrx02 » Fri Feb 11, 2011 11:06 am
neptronix wrote:usually there is a label on it... if it is a cheap brushed controller and it doesn't have a label, the only way to find out would be something like a watts-up, cycle analyst, or turnigy watt meter.
http://www.hobbycity.com/hobbycity/store/uh_viewitem.asp?idproduct=10080
Which, if you're into eBiking, you should have in your arsenal
...
Oh thanks mate. Your help is much appreciated
- mikeswrx02
- 10 µW
- Posts: 5
- Joined: Thu Feb 10, 2011 6:06 am
5 posts
• Page 1 of 1
Return to E-Scooter and Motorcycle General Discussion
Who is online
Users browsing this forum: No registered users and 3 guests