StandUp Scooter with CVP transmission

[Astropower]

Hello Everyone,

I would like to share everyone with you my little work,

List of my scooter parts:

Simple Ballon wheels scooter
16 Cells of 40152 LiFePO4 15Ah
58V 4A Charger
25A BMS
20A Controller
Brushless motor 1.2Kw
NuVinci N171 Hub
DC to DC
12 inch rims
12 inch tires
140mm Disk + Calipers
25# Chain, 19tooth motor sprocket + 54 tooth Hub sproket
thumb throttle + Aluminum Brakes,

See the pictures:

1.JPG (110.57 KiB) Viewed 543 times

[Astropower]

25# Heavy Duty Chain
19 Tooth Motor Sprocket
54 Tooth Hub Sproket

Gear Ratio 1 : 2.84

2.JPG (111.2 KiB) Viewed 543 times

[Astropower]

12 Inch Wheel
+ 12X2.75 Inch Wheel, Heavy Duty 65PSI

3.JPG (133.98 KiB) Viewed 1601 times

[Astropower]

NuVinci N171, Automatic CVP Transmission Hub, Ratio 1:1 to 1:3.5.

Comes with USB Program controller.

Great Product.

http://fallbrooktechnologies.com/

4.JPG (98.23 KiB) Viewed 543 times

[Astropower]

My Cells,

16 Cells of 40152 Size, LiFePO4 3.2V 15Ah, 150A(10C) Discharge 45A(3C) Charge.

51.2V @ 15Ah Total.

5.JPG (102.1 KiB) Viewed 543 times

[Astropower]

[youtube][/youtube]Brushless motor, 1.2KW on 47.5V
1280 RPM, Aluminum Cooling.

8.JPG (83.13 KiB) Viewed 543 times

[Astropower]

DC to DC
from 60-42VDC to 12VDC 10A (120W)
to run the Hub controller and LED Light (soon).

you can see in the picture the Hub controller.

10.JPG (105.58 KiB) Viewed 543 times

[Astropower]

Brushless controller,

I will change the electronic to support 35A instead of 20A.
for long Life run.

7.JPG (83.37 KiB) Viewed 543 times

[Astropower]

The main Problem is with this Hub,

Because the Hub should fit to 36 spokes rims, usually it for 26' 24' 21' inch rims,

to fit 12 inch rim, it litte problem, the Hub is about 9' inch size,

so i buy simple curved sprokes rim,

i broke the curved sprokes, and i design some part to fit between the Hub and Rim, By CNC Cuting.

15.jpg (64.45 KiB) Viewed 543 times

[Astropower]

another one,

the hub is very wide,

14.jpg (69.44 KiB) Viewed 1598 times

[Astropower]

the NEW Part, after CNC Design

16.jpg (75.31 KiB) Viewed 1596 times

[Astropower]

another one

17.jpg (61.53 KiB) Viewed 543 times

[Astropower]

Connect to the Hub

18.jpg (68.24 KiB) Viewed 543 times

[Astropower]

Part 2

[Astropower]

Now need to connect the Rim

20.jpg (80.47 KiB) Viewed 541 times

[Astropower]

After lot of work

21.jpg (99.5 KiB) Viewed 351 times

[Astropower]

different side view

fit Perfect

[Astropower]

Done

23.jpg (91.47 KiB) Viewed 351 times

[Astropower]

Complete 1

24.jpg (118.37 KiB) Viewed 706 times

[Astropower]

Complete 2

25.jpg (74.05 KiB) Viewed 351 times

26.jpg (75.37 KiB) Viewed 351 times

[Astropower]

Now, the original scooter chassis have problem with wide wheels,

so i made some changes,

looks ugly now, becasue it not finish yet.

27.jpg (62.55 KiB) Viewed 351 times

28.jpg (71.69 KiB) Viewed 351 times

29.jpg (76.8 KiB) Viewed 351 times

30.jpg (67.3 KiB) Viewed 351 times

34.jpg (89.81 KiB) Viewed 351 times

I will Update soon...

[agniusm]

This is looking fabulous. great work mare. what kind of speeds/range you expect? I am just finishing my stand-up scooter project, meduza project. was wanderin if you could throw in a link for dc-dc converter. also how much was the motor/controller combo? cheers, nice project, thumbs up

[Astropower]

Thank you for your reply,

the maximum speed is about 42.5Km/h (26.4MPH) in theory.
it will depend finally on the total weight.
simple calculation.

the range i hope it will be more then 40Km (25 miles).. and again, i will know for sure only after real test drive.
but for sure, In low speed or hills, i will save a lot of energy compare to the normal scooter in the market, thanks to the transmission.

about the DC to DC, this is the item that i bought :
http://www.ebay.com/itm/DC-DC-Converter ... 3a68fb8c0f

this is the controller:
http://www.aliexpress.com/fm-store/3138 ... -s-EV.html

about the motor, i dont have information on the web, it cost me about 150USD.

Thank again for your support.

[Astropower]

Hello,

Yesterday i build caliper device.

1.jpg (127.02 KiB) Viewed 351 times

2.jpg (106.56 KiB) Viewed 351 times

3.jpg (130.02 KiB) Viewed 351 times

4.jpg (121.5 KiB) Viewed 351 times

5.jpg (133.87 KiB) Viewed 351 times

6.jpg (128.45 KiB) Viewed 351 times

7.jpg (163.61 KiB) Viewed 351 times

[Lebowski]

cool stuff nice project !