Recent content by Laureloke

Hello. I has 48/60 volt 800watt e-bike controller http://www.ebay.com/itm/401179406972?_trksid=p2060353.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT And I has HobbyKing® ™ GT-2 2.4Ghz 2Ch Tx & Rx https://www.hobbyking.com/en_us/hobbykingr-tm-gt-2-2-4ghz-2ch-tx-rx.html I want to connect them...

Hi! I bought this icharger 1010B to charge 8s LiIon battary pack. When everything is connected properly and I push START, icharger just reloads and does nothing. (in balance mode, in charge mode and in fast charge mode) I also tried to charge 1S liIon and 3S liPo, but It doesn't want to charge...

One motor is better, than 0 motors)) Two motors is much more better than one motor for mountainboard. Maybe for skate or longboard one motor is good, but not for mountainboard because of off-road. Four motors is the best choice. ;-)

Hi, everyone! Here is my new 2wd Build. (previous build was on the first page of this Motor: Turnigy Aerodrive SK3 - 6374-149kv Brushless Outrunner Motor - 2 unit Battaries: ZIPPY Compact 5800mAh 11S 25C Lipo Pack - 3 units ESC: 150A 2-12S Car ESC - 1 unit Hobby King GT-2 2.4Ghz 2Ch Tx & Rx...

I connect 8S 5800 with 2 JST-XH plugs and 3S with 1 JST-XH plug in serial (11S) to balance board. I asked ThinderPower support about right connection, but they told me, that 8S and 3S should be charged separated. I didn't belive them)) And charge them in one time. There you can see some pics.

I had the same problem. Connect your two 6S in serial to 12S. Then connect them to charger. Afte that connect balance plugs to balance board. If you see sparks, then you mean mixed plugs on balance board. Then change their location with each other.

Hello, 3nslav3. Can you show a picture how you connect battaries to SUB-D plug and how you connect TP1430C to SUB-D plug too. This is interasting idea, but I efraid of wrong connection.

Here is my Build. Motor: Turnigy Aerodrive SK3 - 6374-149kv Brushless Outrunner Motor - 1 unit Battaries: ZIPPY Compact 5800mAh 8S 25C Lipo Pack - 4 units ESC: Turnigy Trackstar 1/5th Scale Sensorless 200amp 8s Opto Car ESC - 1 unit Hobby King GT-2 2.4Ghz 2Ch Tx & Rx Sprockets: 9t (on motor) and...

Three days ago I made an experiment with bord and 4 LiPo 8s 5800mA/h (23200mA/h) :idea: Some time people in the city that I live in asking me: How long could I ride on board or what is the fastest speed? This was interesting for me too. :roll: So I instaled GPS tracker on my HTC and rode in...

Thanx a lot! Thats what i'm looked for.

Hello, sn0wchyld. I have an idea of setting car or moto horn (6v) on board, because sometimes pedestrians crowd the sidewalk and prevent pass. But i don't know is it possible to realise this idea with Hobby King GT-2 2.4Ghz 2Ch Tx & Rx :roll...

Try to shift the weight on the front foot and a little sit down. Also, your shoulders should be in front of as many as possible. In this case, even with strong acceleration wheels will slip but the board do not throw you down. If after that you still will not be able to travel without falling...

sn0wchyld Do you know how to prevent motor from running at the top speed, when connection with transmitter is lost (for example batteries in transmitter are dead)? (I use the same Turnigy Trackstar 1/5th Scale Sensorless 200amp 8s Opto Car ESC).

Reduction rate was 5.9:1. Now I have a new motor 6374 149kv and new sprockets with reduction rate 8.9:1 - it's enough to ride with one motor. Haven't found 8085 170kv motor - HK used to sell them. I don't rememer last settings, but now they are: Timing: Low (4) punch control: 100% brakes...

sn0wchyld, why have you used car ESC? I'm thinking of buying plane ESC for example Turnigy dlux 120A HV Brushless Speed Controller (OPTO) (http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idproduct=17982) or may be this Turnigy Super Brain 100A Brushless ESC...