Recent content by matsh

Its not the power its missing. I now have twice the acceleration than before. Ripps hard from start and stops at 48 - 50 kmh. If speed was limited by power it should have bwen more Smoooth. Kontroller has 3 speed option, but this is turned off. Have testet and adjusted max throtle voltage so...

Hi. Here is a link to a shop in poland that sells this model. https://www.trybeco.com/skutery-elektryczne/libra-1-5/ Sent fra min VOG-L29 via Tapatalk

Hi guys. i have a chinese electric moped. stock is max 45 km/h. 60v peak charged acid batterys. in the need for more speed. i made a new battery pack at 80v peak charged and a new kelly controller KLS7230S. i have a ton of torque if i go high in the settings. but the top speed is almost the...

i found that old used motor from salvaged citroen c-zero is relative cheap and easy to get here in norway. Y4f1 motor same as used in couple different electric cars. if i go for this motor then i cant use my kelly keb controller right ? what controller can i match into a motor like this ? if...

Hi guys, im buying an older buddy electric car, its prodused for the norwegian market https://no.wikipedia.org/wiki/Buddy_(elbil) the stock brushed motor is toasted, same with battery. original is 72V SepEx 13kW motor and lead accid batteries. going to use e-up or golf battery cells and a...

nope, but the old big keb 12.000w controller i had was a bit on the big size for this scooter anyway.i know the controller worked when i removed it from my ebike. not shure why i had no working combination with this motor.

did buy a new kelly kls4812s, easy setup with automatic hall phase cenfiguration. supersmooth trothle controll and no sound from the motor. togheter with vw e-up 14s cells and controller at 80 percent im topping at around 3300w measured with a cheap ebay power meter on the battery cables. pulls...

both those functions is disabled in the softvare. and with stock controller at full speed with wheel in the air its pulling 120-150w maximum, with the kelly at the best workign hall phase wiring combo it puls 1400w so something must be wrong. strange thing is both 60 or 120 degree hallsensor...

Hi, yes its not that much to controll in the software. have tried 60 and 120 degree in the sensor settings with the same results. have checked max and min voltage and max amp settings. ewerything seems correct.

Hi guys, my stand up scooter 48v 1600w brushless modell, have changed batterypack and had a big kelly keb controller laying that is not used anymore. tried to wire this up to the scooter/motor but no luck. tried all 36 wiring possibilities, the best one is pulling 1200w with wheel in the air and...

Hi, have you tried with another controller with the stock brushless motor ?i ahve same type scooter 48v 1600w. replaced batteri pack, and installed a kelly controller keb modell, having trouble finding the correct hall phase wiring. i have 1 combionation that works, but with no load wheel in the...

Hi, i have a chinese kick bike its identical like the chaos sport 1600w, seems like they go under different names. i am going to install a kelly controller i have laying around keb 72120 (yes its overkill, but i have it..) and 13s with vw e-up cells. so voltage is around the same. dont need...

Is that okay to do ? I am not shure because the kelly electronic is wired to a 5 cell. And the ca is wired to the 32cell side. So a bit of voltage difference that is isolated from each other. If i wired the earths togheter what will then happen ? Will it be okay? Sent fra min SM-G930F via Tapatalk

No help in turning the ca on first. Most be something with them not have the same grund Connections. Since the ca is wired to the high voltage. And j2 connector on the khb is on a separate lower voltage battery. Sent fra min SM-G930F via Tapatalk

i have the khb12401 Controller to a high voltage pack 32 cell lipo. and a separate 5cell lipo to the j2 Connector. if i wire the throtle directly to the khb it Works great. but i also have a ca v3 i want to controll the throtle with, from throtle to the ca v3, and throtle signal out of ca v3 to...