Recent content by pkirkll

Did you ask grin about that issue? I need one too to go to my control box by grin

Can anyone help me find the specs of this hub motor??? -- i got it when I bought a Greenspeed trike. _________________________ There were 3 pins in the motor wire (pic Attached) And i couldn't figured why it didn't have any Hall sensor wiring coming out of the hub.. The closer I looked at the...

Yeah it looked pretty bleak---- Thanks for your help We got the question answered now to move on to the next project. Oh and what is the proper way to dispose of this unit, paul

OK.!!!! i turned the JST over an SURE enough there were metal access points.. I just put the red MM lead on the red lead of the JST and then i put the black MMlead on every pin to the left.... I dont think this was the correct way

OK thanks here is a picture of the BMS connector-- Im also making a schematic/diagram up so i can visually see where to pin tried pinning the JST plug but i dont have anything that small--- If you can tell me --- Like 'black lead on 15A while red on 10B".... That i can follow--- and once...

i wish i knew where to put the MM probes to test each p group--- at first look it seems they are all hooked together ---do i have to pin each side of the battery at the same time to get a positive and neg pf each p group?? When i finally understand how to test a p group i will be very...

I understand why i dont need to check each individual cell now---- one p group could be bad and from what i have read here--if that is the case then the whole group should be canned. thx

Here are some pictures-- i will have to watch some more video to get the hang of test parallel groups. I did get 3.0v from the B- on BMS and the red wire on charging XT60. No voltage on the B- and red discharge wire XT90. Going to have to watch some more videos to see how to pin the parallel...

Thanks everyone-- i guess I will check the voltage on the battery side of the BMS first. I suppose the BMS has to have some power to be able to send out info on bluetooth. Im down in the desert of AZ but it pretty windy right now dont want to start a big fire so i wont try to charge it right...

I have a battery that has been in the box since 6/2020----- 1 year and 10 months! I know I will get torn up over that,, but remember what was going on that whole time. The question is: since i am assuming the if BMS put it to sleep a while back... would that save the cells or would it still...

Im looking at a drive for the front of my Greenspeed Magnum trike---- Patterson looked way eaasier than this--- i dont think it has to be chamfered.... they are about the same price as ATS--- lot cheaper than Schlump.... ANyone know of any negatives to the Patterson?

Nep,--Lots of edits on this post-- learning more about the trike as i go--- I tried the simulator and didnt quite understand it. Mainly because I dont know much about what to input. I dont know much about controllers, but I will learn. I am also trying to learn the difference the windings...

Glad to be back on the forum... (Still have my Luna Cycle with Mike's Big Block on it.) I may part it out with the Rohloff and BB selling separately. Haven't decided yet... That frame just didnt cut it. It couldn't stand the pressure when i cranked on the BB---the dropouts bent and spread so...

Yay, i was hoping that was also the case....the motors that I have found mention of were going up in nomenclature as they got wider. (right?) It look similar to this one-- i dont know if it is a screw on hub or not. I would like to be able to use it as a PAS motor. (and for getting across red...

That could very well be. Nep All the history i could get was it didn't work for the prior owner. I will give it a go tomorrow and see if it does it with the freshly charged pack. I cant tell if they are charged up or not-- dont have my tools with me. But the cheapo computer will show a full...