Recent content by sleepless

Hi all, I'd like to build the most universal ebike possible. My ebike journey started with a fully which I kinda regret today. The idea was that I can ride it on the road with (mostly) disabled suspension and then go offroad with full suspension. But here's the thing: I'm driving on paved roads...

Hey guys, I also have the Phaserunner and BBSHD setup since yesterday but I have a strange issue: even though I have more power now, the rotation speed of the motor is decreased in comparison to the stock controller (I think). Normally I could go up to 42 kph in third gear but with the...

Thanks guys. You are all right and I opened it up to check them. Thankfully it are Panasonic NCR18650PF :thumb: I knew it weren't bad cells, I just wanted to assume the worst case scenario :wink: so I think I can set 60A I don't need a BMS since I'm monitoring each cell group by myself and...

Hi all, today I got a Phaserunner because my BBSHD stock controller died (again). Without doubt I want to increase the power now that I got this powerful controller. The only way to do this (without buying a new battery) is to set up the max. current to be drawn from the pack. Well, I have a...

I tried this but it seems to not be possible. I currently have PAS disabled via software but when I use the throttle and start pedaling the motor stops :roll: seems like PAS sensor has a higher priority. Will maybe also clip the grey wire. But you aren't pedaling with full throttle, are you?

Hi all, after my first Controller fried after just two month with stock settings I am a bit scared now and wanted to ask for advice. From my understanding I need to make sure the motor is spinning preferably fast. This isn't an issue when using the throttle but when I want to pedal I need a...

OK guys, I solved it for now with a custom reed sensor. I had bought some brake sensors for hydraulic brakes but am not using them because they're very shitty. They just produce error 30 when braking and sometimes it just stays there :shock: Since it works with magnets I thought it'll be a reed...

I seem to be very lucky with my BBSHD. On my first ride I lost the speed sensor. Had error 21 but could at least drive. After just one or two months the controller gave up. Now I finally got the repaired controller back from china and guess what? I'm still getting error 21 which is no wonder...

Thanks for your reply. Well, overnight it stopped working completely. It doesn't turn on anymore. I tried to disconnect and reconnect the controller but still nothing. The wires look good so there shouldn't be a problem. Am I right that it has to be the controller if the battery works well? I...

Sadly it worked just for about 10km. Now it shows error 12H almost instantly and doesn't move :cry: it just makes a silent noise when pushing the throttle. My chinese seller said error 12 means controller error and I should send it back for repair. But that would take very long I think. Does...

Hi fechter, thanks for your reply! It indeed runs smoothly and I feel the motor cogging. The speed sensor isn't needed because I lost it the first day I installed my BBSHD and rode many hours since then without issues. Any other idea what I can check? It can't be the battery, right? If it'd...

Hi, I have a strange problem. I came home yesterday with my ebike and everything worked fine. Plugged the charger in and went to sleep. Today the BBSHD isn't working anymore. The display turns on, battery is at 58.6V almost full. When I start to pedal the BBSHD won't assist. The throttle on the...

Hi, this is a follow up on my other topic. It seems that the BMS is defective. Charging seems to work fine but of course I do control the charging process. My battery seems to be okay. Measuring the plus and minus pole of the battery itself shows me 56V. Measuring the batteries plus and the...

Thank you all for your replies. I got me a multimeter today but I don't feel much smarter now :mrgreen: The output voltage is 42V which is empty and it explains why the display won't turn on. But measuring the cells (or the rows?) shows me 3.9-4.0V which should be almost full. So how can it be...

Hi all, today I drove through a lot of rain. Suddenly the display shut of and the motor stopped working. I thought the battery might have got some water so I opened the hailong case and it was indeed wet. Well, I dried it, cleaned it and re-connected it but still the display won't work. The...