Recent content by tobsie

I am deciding between 2 Cube bikes the Cube kathmandu hybrid pro 500 or the Cube touring hybrid one/pro 500 (both 500Wh battery). The main difference between the bikes are the bosch engines. the kathmandu has the bosch performance CX (75nm) motor and the touring the new bosch active line plus...

Yep, I connected a different (than the original) controller earlier, and I couldn't figure out the green wire that came out of the motor. I think this is a temp sensor and I left it not connected. What should I do with the temp sensor. Is it necessary to buy a controller with a temp connection...

I have this controller in mind http://nl.aliexpress.com/store/product/controller/738588_1873673102.html This controller is max 13A and I asked him if it was possible with a higher Amp. Het told me that he could deliver a 15A controller to me also. He also has this battery...

I also have a Sparta C3 from 2013. I tried all sort of stuff to figure uit the speed control, but didn't succeed. At the end I replaced the controller and display. There is no speed limit anymore. So this is the way to go.

I have a ebike pedelec with a Sanyo cmu-9 brushless motor 24V. I want to speed up my max speed (with pedaling :-)) and want to buy a 36V controller and a 36V battery. Can you advise me on the specs? What is the advice on the Amps on the controller. Is 15A enough (500W), or is it better to go...

I thought the hall sensors would determine the speed of the motor. I indeed also have a magnet wheel sensor for the display.

In the display the max speed is set to 40km/h. So that isn't the issue. The controller and the display are both bought at MXUS. The controller is a 24V controller and in the settings of the display I can't set anything more then I did (there is no way I can set anything on the controller then...

Late reply on this topic. Last week I had access to a 36v 10ah battery. I replaced the current 24V with the 36V battery and left the other parts as is. The torque and max speed became better, but two issue: 1. with the gas handle the display gives an error message above 32km/h. The motor stops...

Great guys. Then I will buy a 36V battery. Can I decide myself how much Ah it has to be, or do I have to stick with 10 Ah (because of the max watts the motor hub can handle)?

Is it possible to add a 12V 10A battery on top of the current 25,9V 10A battery? Or will this not work. For example this one: http://www.alibaba.com/product-gs/770781314/lithium_battery_pack_12v_10ah_for.html?s=p or this one...

I was hoping to only upgrade the Battery and leave the controller as is (hope it accepts 36V). I was dumb enough to order a 24V controller last year, but I am assuming the 36V controller (that they sold) was the same. What considerations do I have to take for the battery. Does is need to be the...

Hi, Last year I modified my ebike. Current configuration is: - Sanyo cmu-9 brushless motor 24V - Controller from http://www.mxusebikekit.com (replaced the standard Ananda controller together with a new LCD display) - The battery is 25,9V 10ah Since I upgraded the controller & display the bike...

Ok thx. The supplier told me that there was an advanced menu for the controller (see image below). They advised to change the value of P1 to 150 instead of the 88 which was default. The motor is know running 29,6 km/h when lifting the front wheel and using the throttle. I have to make some...

Or do i need more testing. I assumed that the color combination of the three motor phases have the be the same as the colors of the hall sensor. Am I correct? So for example the white phase wire from the motor is connected to the blue phase motor wire on the controller. Then I assumed that the...

I tried all 6 possible combinations now. And I discovered that there are 3 false combinations but identical and also 3 posisitive combination but identical. So I am 99,9% sure that the issue lies in the controller now. Since I bought this new, I asked the chinese supplier (which assured me that...