Recent content by twist

Hi Everybody, this is not my day :evil: I have the following setup: 2 Cycle Analyst one runing a C9 2707FD Front Drive Moter with Phaserunner the other runing a BBSHD Mid Drive Moter with Phaserunner I changed one Cycle Analyst to run 5v PAS for the BBSHD PAS Sensor the other I left stock...

I played around a bit and with R2=182 Ohm and R4=23k I get POT 0=0,68V and DOWN=0,28V / UP=0V and everything is working. Don't like that R2 is so low ... should there be a problem? Cheers, Christian

Thanks, I will try that! I just build out of the "Digital Aux Example" (https://endless-sphere.com/forums/viewtopic.php?f=4&t=37964&start=3150#p1196642) the Digital 2 Button with POT Circuit but have also now a small problem :lol: The two buttons are only working right when the POT is on...

Yes, the controller is removed. It broke during a 5000km bike tour and right now I'm preparing for a 10000km bike tour and that is why I have 2 of each. Sorry :). Just the proximity sensor is not working. I just wanted to show the setup because people sometimes don't know where to put the POT...

Thanks, will try to make a wiring diagram. Here are a bit more infos of the setup: 1 BBSHD Mid Drive Moter 1 C9 2707FD Front Drive Moter 2 Cycle Analyst 2 Phaserunner The pot is just for setting the PAS - Levels. I had the same setup running with just a switch for regen-brake and then...

I put a Diode between GND and the brake and now it's a little bit better but still not usable. Now the brake engages sometimes for a milisecond and the Throttle Out goes up to like 1.3v. Maybe somebody has an idea. I'm guessing I have to put somewhere a resistor :roll: Cheers, Christian

I first had a End-Stop switch with metal flap but that broke on my first test ride so I desided a Proximity Sensor (CJMCU-0101) for breaking would be the best idea and it is a perfect solution because I just have to get close to the brake to brake with regen :D Now I have probably a wiring...

Here 3 Photos of the cabling: I used the original cable from the BBSHD that was connected to the controller and cut it off from the controller. Then I just attached a new JST plug to it and connected it to the Phaserunner. For the PAS sensor I just used an old CAT-Cable (you see I have there...

Hi Everybody, working right now also on the same setup. The cabling for this setup is easy if you are follow this threat :) Download and print out the electricwheels.de Wiring Diagram (that saved my day!): https://endless-sphere.com/forums/viewtopic.php?f=4&t=91775&start=25#p1360020 Then print...

Thanks dogman dan for your infos!!! :D Love that bike ... what kind of stand are you using? :) On my last tour I broke 2 stands (https://www.instagram.com/opendocumentary/) :roll: Now I'm still a bit confused but a little bit smarter :) I have orderes 2 Cycle Analyst and 2 Phaserunner...

Thank you for your great input! I now ordered the 9c+ Front 2707 and the Phaserunner and hope that non of my motors break on this tour :) I was in contact with Justin from Grin and he tryed to explain to me the difference between the 9c+ 2707 and 9c+ 2706 when running with the Phaserunner and...

Thank you for the help! After looking at the MOTOR SIMULATOR from Grin and reading your advice I think the 9c+ Front 2707 (http://www.ebikes.ca/m2707fd.html) would be a good choise for me and keeping the BBSHD but with the Phaserunner as a controller. I will be also thinking about adding maybe...

Hi everybody and happy new year, this year I planing a 10000km ebike tour from Spain to Sweden (and back) and will be modifing my bike a lot. 2016 I already did a 5000km ebike tour from UK to Spain with a Surly Big Dummy (https://www.instagram.com/opendocumentary/) with a BBSHD and after around...

Thanks,! Tested the battery and I have as a Charger the Grin Satiator. So the last charges where ok. I had a guy testing a few cables and the display is not getting the 5v or whatever it needs to work and also not the 48v to show on the voltmeter in my display. And the display was also giving...

So I had the motor apart and it must be the controller (90%) Does anybody know a seller in Italy? Right now I am 125km to Verona and will try to bike the shortest way to Marseille (France). Any help would be welcome ... Have to bike right now 80% of the day (while I am awake :)) Not much...