Recent content by Uschi K.

Hi guys, what type / brand of bottom-bracket, crankarm / crankarm-set & axle are you using on your Raptor? It looks for my that I do need a longer axle then for normal 83mm bottom-brackets, as the q-factor Needs to be wider to accomodate the wider frame. Any suggestions / thoughts on this...

Hi Guys, I´ve tried to use Shimano Deore XT SM-RT86 203mm with a Cromotor and I can tell you that I was not able to make it work. These disc does not align very well with anything else than a normal disc-hub. Kind regards Lars

Hi Torque, where can I order the new bigger protector to cover larger controllers? Can you please specific the exact dimensions of the controller that would fit at maximum? Thanks. Kind regards Uschi K.

Hi, so what is your suggestion? Should I set the phase-amp to 1,5x battery-amp as a starting-point? Any additional suggestions to programm the controller to still have a (relativly) smooth start? Kind regards Lars

Hi, I'm a bit puzzled and kindly ask for your help. I've a battery-pack that consists of 25s6p with 3,7V / 2250mAh per cell and a 5C rating. So per my understanding (yes, I know very limited) the total pack should be capable of 92,5V (hot of charger around 102V), 13,5Ah and 67,5A. So far so...

Hi, after basically the riding-season is gone, I managed to get pretty close to finalizing my Torque project. Hopefully you can view the photos I´ve just done today. It´s not done, but starts to look like a bad ass. I´ve actually two things that worries me a bit and where I like to...

Good morning, the bottom-bracket was delivered with three spacers (approx. 2mm each) but it is the axle of the crankset that is to short then?! From my perspective I do need a bottom-bracket with a total width of approx. 100mm at least (incl spacers) and a crankset with an according longer...

Hi guys, I was just trying to fit a bottom-bracket incl. crankset from race-face but i Looks like it is not wide enough to fit the raptor frame. The bottom-bracket is a Standard 83mm which fits the Frame well, but the crankset (especially the axle) seems not wide enough. Actually the crank is...

Thanks pdf! That was the root-cause. Now the wheel is rotating easily.

Thanks ..... I will check as soon as I can. If that is the case, I will fall ashame in a second. I would be such a NOOB! :oops:

Hi, yesterday I was putting my new CroMotor2 for the first time in my Torque Raptor frame with a 165mm rocker arm. On the outlet of the cable, I´ve put three C-washers. On the other side (freewheel) just one big washer. After first starting to tighten the nuts, I notice that the CroMotor2...

Hi guys, I kindly ask for your help and advise, as I´m a real noob when it comes to cabling. :oops: Can you please have a look, if the below scheme is complete and OK? Any suggestions are more than welcome. Thanks!! Kind regards Lars

Hi guys, as some folks have asked about what components I´m planning to use, I´ve tried to compile a list. For sure this is not complete and I´m missing some items. Just a braindump! :mrgreen: Frame: Torque Raptor Bicycle Frame Kit (black/silver) Damper (rear): Rock Shox Monarch 4.2 Fork...

Hi guys, just to bring this into the right light. I´m satisfied with the frame-kit. It is a good product. Some small spots with chipped off power-coating will happen anyway, when riding it. Ziva was always friendly and helpful, answering pretty fast. Nothing i can complaint about. I´ve received...

HI, I received my frame-kit, approx. 8 weeks after I´ve ordered and paid for it. Kit was pretty well packed in a cardboard-box. First impression is that it is well engineered and build. The power-coating is not perfect, but OK. I´ve two / three small spots on the frame, where the power-coating...