Recent content by Waxx44

Yes, it has been so long, now i can ebike to go to work, no need of a car for the summer :D . I encased the controller to hide the wires. It's a 48v 500 Watt but i set it to 250 Watt only, so i hope it won't get too hot. May i will remove the case if i find a solution to hide wires and...

Hi, now everything is ok :D Motor was noisy because my controller was square wave, now with the s12s torque simulation sine wave, my motor is quiet.

Hi, i have a TigerShark battery case (Reention DS-6c), after a short cut, the male power connector has melted, so i'm looking for a new connector. But i don't know the name/type of this connector. I already emailed Reention for it but they don't answer. I asked to the seller from i bought...

What kind of plugs do you recommend ? I've already changed all the plugs by Anderson plugs (bought from Aliexpress). I was thinking about soldering controller's wires with motor's wires. For now motor is quiet (still a bit noisy on first level but it's ok). On s12s torque simulation controller...

Hello, be careful, i bought a kit from banggood, it's quiet with the original controller. I tried three other one, and i can't find a controller as quiet as the one from the kit, they are really noisier. First movie original controller vs kt48 500w (not real sine wave) controller from...

Hi, i've just connected my new s12s torque simulation sine wave controller, it's still noisy, but very less and only on the first level assist. I need a new case for the controller, it is bigger than the other. I have a new problem, when i use brakes, the battery indicator on the kt-lcd3 shows...

I tried all C2 settings, still the same. I'm going to buy a s12s 48v 500 watt torque simulation sine wave controller from bmsbattery. I hope this will be the last one i have to buy.

I think i've found the L1 setting explanation. From the Kt-LCD8S manual : "L1 parameters are applicable to the automatic under-voltage controller. The default of the factory is 0. 1.1 When L1=0, the automatic under-voltage controller can automatically select the under-voltage value according to...

Yes it's really better with the original controller but i can't connect a kt-lcd3. I made a movie to compare original vs kt controller (i bought two kt controller because i was thinking the first one was faulty). I think the kt controller is power limited by software. FaxFeVE7NaI

I received my new controller, and it does exaclty the same thing ! :x I checked again the kt-lcd3 settings again and i found an other setting after the C's settings, this is L1, does someone know what it does ?

Tested and it's still the same, set P1 to 33, noisy/growling motor. I put back the original controller for now, it works well but it hasn't LCD. So i've just ordered a new sine controller 48v 500w rated current 13A, maximum current 26A compatible with kt-lcd3 display.

Inside the controller: I've checked all wires from connectors to welds with a multimeter. I reheated the Mosfets welds. AHicks, no i'm not sure, i'm going to try as soon as i will reassemble the controller.

Thank you for your reply. This is my first try for ebike, i was hoping settings of the lcd3 could change something, but after reading you and docw009, and all i tried it's definitively the controller. May i will buy the cheap tool from eBay/aliexpress to diagnose motors and controllers. At...

I just went bike to compare GPS and lcd3 speedometer, i need to set P1 to 46 to get good speed information, but motor is still growling/noisy/vibrating, mainly at starting (i only use PAS mode). All i have to do now is buying another controller !

I made the little tool with 3 leds to know if the motor's sensors are 60° or 120° and it is 60° 120° cause i can see 2 leds lighting at the same time. So C2 need to be set on 2. Edit: My bad, after reading again this post : https://endless-sphere.com/forums/viewtopic.php?t=3484 If 2 leds...