Recent content by www.evlogix.com

It's possible that the automatic circuit was reset too many times that it's now intermittent in operation. I've sent you a PM with details on the free speedy repair.

I agree. Revisiting the whole text, If you don't want current limiting, you don't have to. Just set it to its maximum, and it'll practically act like a non-current limit because the "limit" is so high. The problem comes in at partial throttle. If a person is using partial throttle, the ESC is...

I apologize if this wasn't emphasized enough in our communication. I don't necessarily capitalize all the time. In regard to the current limit, the throttelizer has a pretty high current limit ceiling so it can effectively work as "not current limited" at full throttle. The problem comes at...

Hello all, we test out all products that are sent out and over 95% have had no problems that couldn't be resolved by email. As with most things, there's the possibility that something will not be connected correctly causing something to go wrong. Since this is the Beta version, if you have this...

We sell a somewhat similar device called the RC Throttelizer with a few more features like a current controlled throttle and customizable throttle ramp, along with temperatuve and LVC protection, along with extensive programmability. Please see http://www.evlogix.com/content.php?link=Rcthrottle...

This problem has not been encountered before, so I don't know the solution right off hand. So, I'm going to try to make sure that the correct port is selected. You should restart your computer, because a port might be hanging open and preventing a connection. If you close the program, and...

I'm confident that if we take this one step at a time, we'll get to the root of the problem. There's a lot of possibilities though on what you're seeing, so I need to get what you're seeing exactly. So this may take a little time. So, you did get to the part where it says "Settings applied. Now...

Hello, I apologize for the problems you're experiencing. I'll try to help you to get through this. So, what suggests that the programming doesn't work? Does a black screen suddenly flash and disappear? Does it attempt to program and then report back with a bunch of zeros for the values? Is...

Yes, the throttelizer is still available. It appears that the original sales post was auto-pruned by the forum, and so the current information available is on the website http://www.evlogix.com. Right now, we're developing a new product and integrating it with the throttelizer, so the current...

It could, although I don't think the police want me to say that. :wink: It could also be possibly used as a "kid friendly" of "beginner friendly" button.

Thanks Powerpedro. We'll evaluate the data viewers soon. On another note, we've had a few questions in the recent past about this, so I'll post here so everyone can know. There's two new variants available. One is the "booster switch" version, and the other is a two current limit version and...

The first two digits are the resistor value and the last digit tells you how many zeroes follow. The unit is in ohms. 155 would then translate to 15 plus five zeros = 1,500,000 ohms which is 1.5 mega-ohms. In any other 1206 resistors, the last digit is the number of zeroes and the digits at...

In regard to the digital resolution of 10bit ADC on typical microcontrollers, it's possible to get external ADC's that provide you with much greater granularity. 16-bit ADC's exist and are fairly obtainable at low frequencies, and dividing 200 amps into 2^16 divisions gets an interval of .003...

In the picture, with the connection between the throttelizer and the throttle, I can see that the signal wire is connected to the blue wire, that power is connected to the brown wire, and that negative is connected to the black wire. According to Fechter at...

Hey, no problem at all. I don't mind bumps. :wink: A new version of the uploading software has been made. Check it out at http://www.evlogix.com/content.php?link=Software_rcthrottle . A user requested the feature to read the values on the RC Throttelizer so that the correct settings can be...