• Howdy! we're looking for donations to finish custom knowledgebase software for this forum. Please see our Funding drive thread

Search results

Date Relevance Most replies

  1. S

    Best sort of frame for a mid drive?

    I had a light Kona Kikapoo with full suspension. I put a BBSHD on it but it flexed too much on acceleration. I didn't like that feel of the frame deflecting sideways. I now ride the Kona analog and have a BBSHD on a DB Haanjo aluminum cross country hardtail which is much stiffer. I do wish I...
  2. S

    Threads on sensorless vs. sensored?

    A-DamW, thanks. It is too far down for me, or up. As you can see from my reply to Spinningmagnets, I just want to know what will work or might work. I don't need maximum efficiency. And i am out in the boonies so I don't have to worry about maneuvering thick traffic where every instant...
  3. S

    Threads on sensorless vs. sensored?

    Spinningmagnets, thanks for your reply. What I am trying to find out is whether I can run a hub motor with one of several no-name controllers. Do I just connect the phase wires, power it up, spin the wheel and turn the throttle and see if it works? Or is some other wiring configuration or a...
  4. S

    Threads on sensorless vs. sensored?

    I am trying to understand the disadvantages of running sensorless. Also, how do I know if my controllers will run sensorless?
  5. S

    Efforts, rebuilds and upgrades Stromer ST1,ST1x etc

    With your bike with the front hub motor, what hub did you use on the back instead of the TDCM? Mainly I want to know how to get an axle long enough. Or did you just squeeze in the frame? Thanks and great work!
  6. S

    EZEE system fires for a fraction of a second. Why?

    Thanks so much for your post. Since I have wiggled every wire many times and plugged and unplugged and changed batteries and taken apart the controller to check for loose wires, I was pleased to see another approach. I didn't check the hall sensors but your post encouraged me to return to the...
  7. S

    SOLD! I'm getting rid of old junk -- controllers, chargers, etc. $20 + shipping.

    I'm happy to take it all.
  8. S

    EZEE system fires for a fraction of a second. Why?

    Hi All. I have an old Yuba Mundo with an Ezee front hub motor system purchased from Grin (I’m not the first owner). It is a set up with a potentiometer, a CA, a pedal sensor and a 25A controller. The system was working fine. Then it was working intermittently and it seemed that fiddling with...
  9. S

    Understanding and Using EGO Power+ Batteries

    Yes, I have a Terrafirma adapter for my Ego batteries. The adapter works well but the screw hole pulled right out when I tried to mount using it.
  10. S

    SOLD: Mac 10T rear wheel kit w/ CA3

    Thank you, Amberwolf.
  11. S

    SOLD: Mac 10T rear wheel kit w/ CA3

    pm me your paypal ID. I'm getting your pm's, I don't know if you are getting mine. Stu
  12. S

    SOLD: Mac 10T rear wheel kit w/ CA3

    pm me your paypal id.
  13. S

    SOLD: Mac 10T rear wheel kit w/ CA3

    PM not sure if it is sending. Leave it In the wheel. I don't know which bike I will use it in yet. Will relace if necessary. Thanks, Stu 518 672 7302
  14. S

    SOLD: Mac 10T rear wheel kit w/ CA3

    I will buy it. I sent you a PM but it is not leaving my outbox for some reason. I'm at 651 Harlemville Rd, Hillsdale, NY 12529. Look up the shipping and I will paypal you. Stu Summer 518 672 7302
  15. S

    BBSHD runs 7 seconds, then stops. Help!

    Okay, I have to fess up to a combination of stupidity and dyslexia (which I didn't know I had.). Turns out the problem was that the motor just does turn itself off if there isn't any load. I didn't have the chain connected and so the motor would run and then turn off. This was after...
  16. S

    BBSHD runs 7 seconds, then stops. Help!

    It is an older system. Many miles on it. I have replaced all of the anderson plugs in the controller, which have shorted over the years. I thought the last Anderson was the problem but the problem continues after replacing it. If I put it on a higher assist level, it does go faster but still...
  17. S

    BBSHD runs 7 seconds, then stops. Help!

    My BBSHD runs for 7 seconds, then stops. It runs only at one even speed, regardless of how far the throttle is turned. It will only run again if turned off and then back on. And then only for 7 seconds again. The “crank” image comes on after the motor runs. It turns back off when the system...
  18. S

    Crystalyte X5303 Racer and controller

    I'm interested if it is still available and if you will ship it. NYS Stu Summer
  19. S

    Do you use an fairing or partial fairing on your ebike, emoped or BSM?

    I ride two bikes with fairings. In snow and ice and for short rides I take my Haanjo CC bike with a large Zipper, a BBSHD and studded snow tires. The fairing keeps me warmer. I take off the fairing (and switch tires) in warm weather as it makes some noise. In better conditions and longer...
  20. S

    Too many idiots on the streets

    I now have two blinkers on the back of my bike and intend to put a strobe/blinker on the front. As a car driver I find them annoying, especially the front strobes, and that is the point. Even as a super bike aware car driver, I still notice the bikers more with the annoying lights and am safer...
  21. S

    LIQUIDATION SALE! UNUSED 48V 10.5Ah 30A battery pack - $65

    Seems like it.
  22. S

    LIQUIDATION SALE! UNUSED 48V 10.5Ah 30A battery pack - $65

    I'm interested in a couple of batteries and the hub motors. How do you ship, how do you want payment, and need photos of the hub motors.
  23. S

    Trouble shoot me!

    Actually, it is the other way around.
  24. S

    Trouble shoot me!

    Now, with the CA connected, I get 8 flashes, which according to your chart indicates a phase wire issue. With the CA disconnected I get 3 flashes and then 5 flashes, then 3 then 5..... indicating according to the chart a hall wire issue. I guess that means I need to open up the motor...
  25. S

    Trouble shoot me!

    So I bought a new potentiometer from Grin but it's not the problem. The system does exactly the same thing: a very brief pulse of power to the wheel and then nothing. What could cause this tiny pulse and then cut-off? Thanks!
Back
Top