Search results

Date Relevance Most replies

  1. A

    Axiom: a 100kW+ motor controller

    hi i'm still alive ...the race was not very good rain ... I'm a little busy with school and work in the garage ... but I think at the end of September or October I will return to full time again ... but if anyone needs help... I am ready to help everything I can... I also watch batteries ... I...
  2. A

    Axiom: a 100kW+ motor controller

    Hi Unfortunately not ...I do not have the opportunities to test resolver now ... I restored everything to working condition (after the last test) ... Now I work with a gasoline engine ... I have race july 20-21 ...I'm preparing and set up the car (engine) ...
  3. A

    Axiom: a 100kW+ motor controller

    what do you think when we can start use IPM motor ...
  4. A

    Axiom: a 100kW+ motor controller

    what do you mean ( Prius power stage ?? ) motor or inverter ...
  5. A

    Axiom: a 100kW+ motor controller

    you see my bus bar on current sensors is short and iron bolts are very close (they touch the sensor) ... stainless steel bolts solved the problem ... yes big motor have resolver ... next step connect big motor and resolver ...
  6. A

    Axiom: a 100kW+ motor controller

    do you have any idea when we can start use IPM motor ???
  7. A

    Axiom: a 100kW+ motor controller

    first ... do not connect 2 PCB together ... you need fixed main PCB bord ... you need 15 volts ... check page number 6 ... The on page 6 describes how to solved this problem . after you see on you multimeter 15v 5v 3.3v on your mayn bord we will proceed to the next quest))) p.s.also if you...
  8. A

    Axiom: a 100kW+ motor controller

    hi ... I'm still alive ...I don't use high voltage yet ))) :mrgreen: :mrgreen: I'm still learning how to use whole system ... My battery is 60 volt maybe it's the problem to pass correct FOC ... Because motor is 36 volt ... ????? small video my update ... I apologize for my french video ...
  9. A

    Axiom: a 100kW+ motor controller

    I think I burned again AMC1311BDWV 3units ... I have extra so I will replaced today and we see if it's start working ... I think it's amc1311 is burned when I try to do FOC settings on my IPM ... is possible ???
  10. A

    Axiom: a 100kW+ motor controller

    Hi ... I bought SPM motor To be sure that the inverter (driver) that I assembled works correctly ...))) I also replaced the parts from AMC1301DWVR to AMC1311BDWV all 4 units ... i replace to R9 = 8.2k and R10 = 0 Ohm ... and it doesn't quite work right see video ... https://youtu.be/CjrXcEVsuvY
  11. A

    Axiom: a 100kW+ motor controller

    as i know the magnets are inside the rotor ...and this is so that if they break then they remain inside the rotor in the same position ...the only difference is their geometric arrangement ...Tesla on model 3 uses Halbach Magnet style
  12. A

    Axiom: a 100kW+ motor controller

    Hi ... i got and installed AMC1311BDWV I understand that I need to mount (to replace) R9 R10 from 1K to 8.2K resistor ( In four places ) ? Thanks ...
  13. A

    Axiom: a 100kW+ motor controller

    hi it have 2 types of resistor PR02 FS 0202208KR500 (Metal Film Resistors - Through Hole 2watt 2.2ohms 10% Fusible NonInductive ) PR02 00 0202408JR500 (2.4 Ohms ±5% 2W Through Hole Resistor Axial Automotive AEC-Q200, Flame Retardant Coating, Safety Metal Film ) in data sheet say i need...
  14. A

    Axiom: a 100kW+ motor controller

    hi I was a little busy with another project (RusEFI) ... checked some points with oscilloscope (and with my understanding I did not find any problems) ... but I think I found a problem ... i have infineon FF600R12ME4 and as I understand it, I need to install on GATE DRIVER resistor...
  15. A

    Axiom: a 100kW+ motor controller

    Maybe this one ...300 amps ... https://www.mouser.com/ProductDetail/ICE-Components/ISB-300-A-802?qs=sGAEpiMZZMt5HSdYdJgvycKzNgY%2f7c8jm4nIHzsVv52Awl3Hhjwu4w%3d%3d https://www.mouser.com/ProductDetail/ICE-Components/ISB-300-A-800?qs=sGAEpiMZZMt5HSdYdJgvyVVVySDmxPWRovMskWuTZcZH5p0dE0cO6g%3d%3d
  16. A

    Axiom: a 100kW+ motor controller

    Hi ... is it possible in more detail which elements should be replaced by ADCMP392ARZ ...(It will be great if you point it to the pic) I still have a problem with crashed firmware ... and when i run the motor parameter detection i dont hear no noises ... what the oscillograph oscillation tells...
  17. A

    Axiom: a 100kW+ motor controller

    hi ... I think I have progress for the better ... ))) I did everything needed with binary file ... and changes appeared volts are shown correctly in vesc_tool_0.95 ... but the motor is still not spinning .( how can i check with oscilloscope that I have signal goes to from brain bord to...
  18. A

    Axiom: a 100kW+ motor controller

    Hi I fixed the links ... I changed the location of the capacitors ... does not look very good but it's all temporary.( I need the first step to make it all work )
  19. A

    Axiom: a 100kW+ motor controller

    maybe its help you ... I use and buy here ... https://www.ebay.com/itm/1Pcs-FF600R12ME4-INFINEON-IGBT-MODULE-with-DRV6T-OP5605-INVERTER-DRIVE-PLATE/192730475493?hash=item2cdfa1abe5:g:xrEAAOSwUKxYbeqg:rk:17:pf:0...
  20. A

    Axiom: a 100kW+ motor controller

    hi I still have problems with start ... I changed the fried Components (and this problem was solved)))... I disconnected and checked the IGBT modules (they seem to be working) ... I don't know how to check IGBT driver ? there is also a problem with VESC bootloader sometimes crashed without...
  21. A

    Axiom: a 100kW+ motor controller

    hi... I don't have a 110k resistor ... I added 270к to the resistor ... and I think it would be nice to add a jumper for versions with 15v and 24v and small description on pcb why they are needed ...
  22. A

    Axiom: a 100kW+ motor controller

    hi i have a problem on first pic we see (main board GATE_DRIVER_CONN_U) connector ... power supply to this connector 24V ...... on in the second pic we see (power_integrations_interface GATE_DRIVER_CONN_U) connector ... power supply to this connector 15V .. on the third pic we have a...
  23. A

    Axiom: a 100kW+ motor controller

    hi maybe it looks like it works AMC1301 and I see battery voltage but with an error ... also it seems to me in the photo messed up with designation ... also i found my mistake with LM1117 I have 3.3 volts on PCB ... i ordered fo 5V i think its helping...:))) Thanks ...
  24. A

    Axiom: a 100kW+ motor controller

    HI I found a couple of mistakes ... one of them seems critical ... in the photo below it is marked as number one ... I messed up two wires in the middle ... is it possible to destroid amc1301 ??? number two ??? i ordered AMC1301DWVR and AMC1311BDWV Current Transducer has current flow...
  25. A

    Axiom: a 100kW+ motor controller

    And I have a problem ...S.O.S... when i try to do (motor setup wizard) then i used option BLDC or FOC its not detect Parameters ... and in the first photo below right, I volts they are not correct there is about 5 volts the difference between what I have on (capacitors, battery) ... on pic is...
Back
Top