Endless Sphere

Hows this? MUTUAL INDEMNITY AGREEMENT Agreement between [party 1] and [party2] Each Party shall hold harmless, indemnify, and promise not to sue. Waive, release, and discharge from any and all liability. Vow not to contact any law enforcement agency, or press charges against the other party and its...

I'm not a lawyer, but research:
release of liability/ hold harmless/ mutual indemnification

I have two of these kits which I am unlikely to use. Still in box.

$250 each, plus shipping from Sunnyvale, CA

a table tennis forum I follow is run and maintained by an online table tennis retailer. While people don't fund it, they do look favorably on the retailer when they buy equipment. The table tennis forum doesn't have the issue of being anti rival suppliers, though, so it may not work for ES if a supp...

see his attached drawing - 70mm, unless you cut 70mm off

from his profile, Washington, Northern California

atarijedi wrote: ↑

Jun 01, 2018 11:36 pm

On the Domino Throttle, 1 is ground, 3 is 5V, and 2 would be the signal.

So you would connect Domino 1 to CA 2, Domino 2 to CA 3, and Domino 3 to CA 1.

I have the same setup, haven't wired it up yet though.

excellent, thanks atarijedi.

Apologies for asking such a basic question, but to connect a Domino throttle to a CA - what wire connects to what? thanks!

219 driver sprockets including the 18t are $20. I’ll throw in the necessary extra 219 links at no charge. You will need a 219 chain tool if you don’t have one. You can get an inexpensive one here: https://cometkartsales.com/-219-Chain-Tool.html The throttle plug on the CA is a 3 pin JST, which is w...

thanks LR, the 18T and extra chain sounds good. Please let me know (message / FB) how much.

Do you know if the domino throttle https://www.lmxbikes.com/en/spare-parts ... ottle.html is plug and play with a CA?

Going slow is aggravating the tendency to wheelie while climbing. If you got some speed up before hitting the hill you’d have a lot less trouble. agreed, but where you slow down/ tap off the power, and then pick up the speed again, the power hits very suddenly - that is where the bike jumps. Partic...

LightningRods wrote: ↑

May 28, 2018 10:46 pm

I’ll work out some of the speed options for you. Changing the front motor sprocket to an 18t for instance will raise top speed to 36 mph without changing anything else.

sounds good! that's all I need in terms of speed - and I guess it would quieten the chain? (not that that is a major concern)

There are several motor driver sprockets available. 12t through 18t. You currently have a 12t which is the lowest. Maybe we should try raising the gearing. Hi LR, I think that would be good - I was wondering if I could change the front sprocket. At the moment, the bike tops out at around 24mph on t...

so… I took the Beta for a hill climb modulation of power is so difficult when climbing - bike wants to wheelie continually! I did it as slowly as I could, just to keep the front wheel down - wanted to lift all the time! 1dKuVUgcYaw in contrast, my wife could use all the power of the BBSHD - it conti...

Hi. Is this project moving forward? This construction is awesome and I am waiting to hear some news from you. yes, finished! Sorry, should have cross-posted to/ from other thread - https://endless-sphere.com/forums/viewtopic.php?f=6&t=71666&p=1375772&hilit=futr#p1374617 will have time to go for a l...

That looked much better. Will have to think a couple of days about if I should order or not. Too bad it is from USA, so expensive to buy from there with shipping and all extra fees also. But at least I know it will fit with your modification. You don't know any local table tennis players that are g...

pictures of stand up and down

Rix wrote: ↑

May 02, 2018 2:54 pm

NIce job on the kickstand.

thanks!

The modification looks nice! But is the kickstand all the way up on the last picture? Looks a little like it has an angle a bit down so it is not aligned with the bike in upper position. No problem when riding in harder conditions? no, not all the way up - when it is up, it aligns perfectly just un...

a question on this: the higos from the brakes have two wires, a red and a black. The CA JST-4 has 3 wires: 5v red, ground black, and EBK blue. How does this get wired up? thanks. Just connect the Ground black and EBK Blue to the two wires from the brakes. Don't need the 5V for these brakes. I have ...

getting back to the Beta kickstand discussion: using one of these https://www.ebay.com.au/itm/Universal-Motorcycle-Clamp-On-Side-Kick-Stand/382297802357?hash=item5902b98675:g:biIAAOSwyXNaHufh, which is too long, I cut it down (initially with a dremel, then bought a pipe cutter - very useful tool); b...

sent you a PM!

thanks teklektik - I'm going to need to keep your note handy for the rest of time!

At ThrO->MinOut = 1.38, and ThrO->MaxOut = 3.85, it is absolutely perfect.

around 10.30am?

struggling with throttle in/ out settings a bit... at Setup Throttle In , Zero throttle is 0.85, WOT is 4.28 so, I set Thrl->MinInput to 1.00, and Thrl->MaxInput to 4.13 Thrl->FaultVolt is set at 4.55 ThO->MinOut is set to 1.00, and ThrO->MaxOut is set at 4.13. When I use the throttle (you can here ...