Endless Sphere

I was in magura stand on the Taipei International Cycle Show this year and asked if they would be doing a MT-7 E version. And they told me that was not on their plans for the close future.
So this is a bit strange.

You can do same thing if in your country throttle is not permitted. Just hide the switch

Hello!!
Someone going to Taipei cycle show this year?
Never been in Taiwan before... any advice?
It would be nice to meet other ES members

https://cdn.shopify.com/s/files/1/1462/0882/products/motor26_4cfa23c8-fcca-42f6-898b-468f4c4f2b0f_1024x1024.jpg?v=1483600021 11Kv Motors EDGE 1500W -35mm Magnets -Aluminum Stator $199 Bare motor $299 Laced in either 20" BMX, 17" Moto, 19" Moto $329 for 26" Sunringle MTX 39 38mph @ 48V 50mph @ 72V r...

Allex wrote:Ah you get used to it! Once you do a couple of runs at 100kms then 80 is the new 40, nothing special, haha.

Same thing i feel

Ive been looking what other alternatives we have to shinko are out there for 19" wheels. I have found : (not counting the veeruber) *Maxxis M-7305 *Maxxis Maxxcross Desert ITM-7305D *Mitas C-18 Any of you have used any of them? I have never used a Mitas tyre and Maxxis is only known in europe for bi...

There is two different things, EU (CE in France) certification, that is mandatory for any product/assembly/kit you sell, wether it is built or imported, and road certification. To make your product comply with CE norms, you have to make some test and reports for the different applicable norms, a de...

Had two bikes last summer, one with M2, another with Hope X2 ( http://www.chainreactioncycles.com/se/en/hope-tech-3-x2-disc-brake/rp-prod112988 ) All I can say is that when swapping to the bike with M2s it felt like I did not have any brakes at all :mrgreen: Huge diff. And the bleeding with DOT is ...

In most parts of western EU it is illegal to drive ANY motorized vehicle offroad, except farmers vehicles or on private own land, but even there only if you can proof certain requirement, e.g. for transport, hunting, etc. Unfortunately sport and fun is not accepted as requirement. There are 3 excep...

How fast have you been when trying the regen? I see you have mInimum speed set to 3, this equates to 30mph or 30kph depending on your settings It was hcv limit that chaged with the reset. Hello guys, I have a problem with regen :cry: I have redone the hole bike and now i dont know why regen does no...

Hello guys, I have a problem with regen :cry: I have redone the hole bike and now i dont know why regen does not work. I thought it could be a bad conection but adaptto detects it cause i can calibrate it with no problem. It seems like is not activated or something similar cause then when i am ussin...

Thanks for the info, Jim: with the bigger rotors, what sort of caliber adaptors do you need (if any)? Here is a link to McMaster Carr my source for hardware. You can get stainless steel machine screws and spacers there. https://www.mcmaster.com/#unthreaded-spacers/=15z9kyw For finer height adjustme...

Yes i did. They got back to me on the 10th of January, i assume this was straight after the public holiday. my controller has just landed to them in Russia. The best email that i am aware of is Oleg's.... olegk@adaptto.ru This is the email address he always replies on. Thanks Bud. Mine landed to Ru...

Thanks for that RIx. Your right the weight saving is irrelevant. The stopping power over the MT5s however isn't. Big difference and imo well worth the extra spend. Oh and they are sexy! Your whole bike is sexy, nice. I didn't think the MT7s were much improvement stopping power wise over the MT5, I ...

Maybe i am telling a stupid thing but... would not be easier to just make a small hole and spray in that liquit type of insulation that expands. Polyurethane i think is called.



Ups i think we are talking of same thing

captain387 wrote:Check out this thread for soldering location and programming.

https://endless-sphere.com/forums/viewt ... =2&t=66169

The programming isn't as straight forward as one would think, but it does work.

Thank you. Had read that post but was before all that info was posted.

A

Alexander1971 wrote:

Now that you have nearly sold every charger.
Could you please show the comunity how to program eaton? and were do you solder the usb to do it?
Read sometime ago it was possible but never seen it.
If there is another place were i can read about it please post link.

Tucked away! DSC07502.JPG Had to do some washer mods to have a nice cable exit without rubbing the disc screws. DSC07505.JPG DSC07506.JPG Also had to mill down the rear brake caliper and space out the disc with 3 washers to have a good fit DSC07509.JPG 22s6p battery fits easily inside DSC07493.JPG ...

Anyone managed to make contact with Adaptto over the past few weeks i have tried two different email addresses and have left a message via their support page on the website but i have not heard anything back since sending the first message nearly two weeks ago. :( They are not usually quick... i am...

Rix wrote:So do the black side covers perform better than the green side covers? Man, if the black performs better, I am spray painting mine black.

You made me laugth
I think black screen gives you 1kv more

Magura should work but if you want to change i recommend you to use Domino. For me and much other people is a better option than Magura.

hmm...my "old" MaxE has also AWG8 allready and latest RC4 firmware had also 200DC Amps. I posted a few screenshots with 17KW allready. but maybe you can tell me why or how it was possible that a buddy of me got an Display with GREEN Sidecover? first we thought it was an old display. but the buttons...

drew12345 wrote:I received mine last week. Thanks Merlin!


Sent from my iPhone using Tapatalk

Me also, thank you!!

It was great it did not had to go throw customs... cause i dont know how would i explain what it is, all of that syringes full of black liquit, if they stop it

(Presell) QS Motor 500W~1000W 205 Electric Bike Spoke Hub Motor More QS Motor Informaiton: For more information, please feel free to contact with us. 1000W 135mm dropout for 7 speed freewheel http://www.cnqsmotor.com/upfile/2016/10/26/20161026115706_457.jpg http://g02.s.alicdn.com/kf/HTB1zv7kNpXXXX...

up to you. you can do "somewhere/sometime" stuff or just what justin measured/find out ;) Lol, You where the first one talking about "should be fine" :lol: If i put more than 5ml on the mxus it sounds and sometime leaks. This is what Justin said: "We're packaging it in a 10mL syringe, and for most ...