Search found 168 matches

by Longshot
Apr 30 2019 8:01pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Multimeter have to show something. Schematic for temp messuring should be quite simple: voltage divider with tempsensor on low side. R83 is in series with temp sensor. Are you sure it is 15kohm? Yes, it is an E96 marked 18C. I replaced it with a 0603 1% 1/10th watt. I reset multiple times and loade...
by Longshot
Apr 26 2019 1:15am
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Please reread my last few posts about what my problem is and why I replaced the resistor
by Longshot
Apr 25 2019 9:38pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Replacing that resistor didn't fix the temp problem. I don't even know if that resistor was bad because apparently my Milwaukee multimeter doesn't read the ohms on these resistors. When I tested the new resistors with it I got no reading. I had to switch meters. I'm so bummed. The controller was lit...
by Longshot
Apr 25 2019 1:24pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

The 18C temp resistor size is 0603 for anyone that needs to know in the future
by Longshot
Apr 21 2019 3:41pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Sorry guys but I'm trying to source the SMD at R83 for the motor temp. I get that it's a 15k ohm 1% EIA-96 resistor. I measured it at 1.85mm X 1mm to try and figure out it's wattage but that doesn't correspond to any size I can find. Is it a 0805 size which would be 0.100 watts?
by Longshot
Apr 17 2019 3:32pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

I pulled apart the controller that had a short with my old MXUS motor and I get 4ohms at R113. So I put it back together and plugged it into the cromotor that's on the bike at the moment. The first thing I noticed was that when I hooked up a light bulb to the controller to charge the caps before plu...
by Longshot
Apr 16 2019 9:57am
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

No, I need to replace the that resistor. I need to do the R113 on my other controller, too. :roll:
by Longshot
Apr 15 2019 1:32pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Nevermind, I figured it out.
by Longshot
Apr 15 2019 10:01am
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Perfect. Now I looking for a replacement. Got the specs on this SMD?
by Longshot
Apr 15 2019 9:19am
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Can anyone show me which resistor this is on the max-E PCB?
by Longshot
Apr 15 2019 8:18am
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Uhg, ok thanks
by Longshot
Apr 14 2019 8:40pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Can some one share any Adaptto Max-E firmwares they may have because the site no longer works. I'm looking for most recent locked and unlocked.

Thanks!
by Longshot
Apr 14 2019 6:16pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

I have a problem. My thermosensor was stuck on 32T so I decided to try different sensors in the controller setup menu and now the temp bars are flashing and I can only get 20 watts. I'm guess I'm stuck in protection for overheating mode? I've even tried setting thermosensor to no but nothing works. ...
by Longshot
Apr 13 2019 3:42pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Thanks. I'll look into that. I thought that the BMS is actively uprating the voltage when using the charge coil. Is that the delay you are talking about?
by Longshot
Apr 13 2019 3:37pm
Forum: E-Bike Technical
Topic: Cromotor out of balance?
Replies: 3
Views: 227

Cromotor out of balance?

https://www.dropbox.com/s/lq04nl5yf4kwmvp/2019-04-13%2015.48.21.mp4?dl=0 Can anyone tell what's wrong with my motor from this video? Are the bearing crooked or something? Bent axle? The motor has never been ridden but it was disassembled and modified. The problem seems to be on the crank side. The a...
by Longshot
Apr 12 2019 10:13am
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

I have a question about charging. I'm taking the bike on a trip and I want to be able to charge the bike as fast as possible in the middle of nowhere. Can I hook up a DC-DC converter to 5s car batteries and charge at 70A with 70A charge coil? Is there anything I should watch out for besides my bike ...
by Longshot
Jul 27 2017 8:19pm
Forum: E-Bike General Discussion
Topic: Build/Repair NYX QS 205 MAX-E
Replies: 2
Views: 468

Re: Build/Repair NYX QS 205 MAX-E

The picture function is not working with my android laptop. This will have to do until I can dust off the laptop.


https://www.dropbox.com/s/lhwrr4lxbquiv ... 3.jpg?dl=0

https://www.dropbox.com/s/q1o8hizy8so38 ... 3.jpg?dl=0
by Longshot
Jul 27 2017 8:00pm
Forum: E-Bike General Discussion
Topic: Build/Repair NYX QS 205 MAX-E
Replies: 2
Views: 468

Build/Repair NYX QS 205 MAX-E

Ive never done a thread like this but here it goes. This is the NYX Interbike from 2015. Ill do a parts list and stuff. It was built with a MXUS 3000 but it shorted out 3 days after I got it. I skipped fixing the motor and bought some qs 205's. I want to have a back up motor so now I have a Hutch GP...
by Longshot
Jul 27 2017 3:01pm
Forum: Items Wanted
Topic: Looking for NYX Hub Wire Washers for QS205
Replies: 3
Views: 699

Re: Looking for NYX Hub Wire Washers for QS205

There seem to be some versions of these posted on youtube by doc. Wondering if anyone's got them or if they were ever even sold. This one in particular: gaKO2E9JcGY Has anyone got these? Ready to get a few. Ill buy 4 but they are impossible to buy from NYX. I have a the NYX from last years interbik...
by Longshot
Jul 22 2017 12:22am
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

BTW , Oleg says that reflashing the firmware will reset your original shunt value
by Longshot
Jul 22 2017 12:20am
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

smurphy wrote:Yes it will. Power is cut when you break or regen.
Power is cut to the motor or power is cut to the 5v throttle lead that isually goes to power a halls throttle. Anyways, i guess im going to test it and find out.
by Longshot
Jul 21 2017 1:25pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

I think you can skip the resistor if u use Magura in combination with variable regen. Why yes, thats what I want to do. I realize that, yes, i can power stuff off it but will the controller cut power to that throttle -+4.8v at any time? There is an option to cut power to the throttle during regen, ...
by Longshot
Jul 20 2017 11:48pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Hey, im having a go at a variable brake sensor and I would like to know if I can power the brake sensor with the 4.75-5v thats going to throttle? Im using a magura so I have a resistor in my throttle wires. It seems like a conflict of interest but if its just sucking 12ma off, its in a convenient pl...
by Longshot
Jul 11 2017 8:27pm
Forum: Items for Sale - New
Topic: Advanced ADAPTTO controllers and compatible products
Replies: 1577
Views: 234887

Re: Advanced ADAPTTO controllers and compatible products

... Controller has to be on. ... Coil or charging connectors had not to be connected. ... This "bms" is not what you may expected. It's more a safety feature. It bleeds only the cells down to your voltage you like. Not really balancing cells out. If you setup your bms to 4.15 it will bleed down all...
by Longshot
Jul 11 2017 8:20pm
Forum: E-Bike Technical
Topic: Adaptto Mini-E/Max-E Owner's Thread
Replies: 5127
Views: 571456

Re: Adaptto Mini-E/Max-E Owner's Thread

Can someone point me to the info on how to replace the fuse in a max E? My motor fried it. There is no fuse in the controller but if you refer at the HALLS error after a short between phase and halls wires here is my solution: https://endless-sphere.com/forums/viewtopic.php?f=2&t=61183&p=1277234&hi...