Endless Sphere

Super73 with BBSHD , Sturmey Archer 3spd IGH Battery 52v/30a with Sony VTC6 cells and Bluetooth bms (40a continuous , battery can hold much more ) i have to check on other phone if i still have photos when I build the battery Display DPC18 Full fenders from UrbanDrivestyle( good protection on bad we...

I have a new Phaserunner with BBSHD harness and cycle analyst v3 bought from Fasterbikes.eu I just tried to configure it for bbshd but i not continue, lack of free time and i just ordered a Frey Ex -External speed sensor it's not connected , i buy the cycle analyst without it but i add a spare old o...

It should be the same for all 3 speed modes, you don't have to connect the self learning for each .
Maybe this is the way the controller reacts when you try to switch the modes under power.
I use the 3 speed switch with cycle analyst and when I use the throttle it cuts power for a moment

I have this code 8 error 2 times on my BBSHD . The motor its new, I use the bike 2 days to go work, 14km one way , 3-5°c. I get to work, everything ok, after 9h, the bike sit outside, same temp, when I want to leave code 8 error. My friend push me with his bike so I don't pedal all the way back and ...

There will be available different bottom bracket sizes , 100 or 120mm?

Hi, anyone use the phaserunner with a bafang fat motor , G060? I have the 750w rear motor, I did the autotune but when I apply throttle the motor its juddering , feels like the power it's pulsating to the motor. I have the cycle analyst v3 for a few years and just updated to last version now, maybe ...

Yes , it's the speed sensor. I see it on many bafang motors without halls.

You could fit ~150 cells + BMS in the em3ev bag

Hi, I read many topics here but I didn't see anyone trying to connect a BBSHD controller to a hub motor. I have a 750w bafang fat motor and I try 2 controllers but both are cutting power after a while when the battery is full. First I use a 25a 9fet kt controller and after I change to a 30a 12fet co...

You can tell where the wires go?

Hi, how you weld the bolts? They hold or is the risk to get off from the tabs?

With 3 speed internal hub would be ok, but single speed its not so great. You have to think about this option

Yes, I leave only the board with hall sensors, take the wires out from them and motor phases. I try first with a square wave 250w controller but it doesn't work well, too loud and jerky. I change to a sine wave controller and it works great but I use it on 48v and 30a and break a few teeth on a plas...

Meanwhile i read about capacitors and they are linked to ground. On the board the capacitors are between signal and gnd. I will let them i guess they dont make any harm if shimano use them. Going to solder the cable, i hope this week i will test it. I am curious if i can use the torque sensor from t...

Do you think its ok to use the board how is now?
Betwen each sensor signal and +v/gnd is a smd capacitor.
The capacitor is used usually betwen +v or gnd?
Should i remove them?
Thank you

Sorry but i dont see any usefull information in your image. I see on many diagrams that Gnd is pin 2 but some its pin 1

Hello, i need some help to find + and - pin on this type of hall sensor
I think + its pin 2 and - pin 3 but i am not sure .
The board its from shimano steps e6000 motor. I want to connect to external controller and use it with throttle.
W10b smd hall sensors

Hello, this is my first post here but reading this forum for ~2 years. I just bought a spot welder (sunkko 709ad+) and made a 12p10s battery using panasonic pf cells. Now i dont know if i should put on a cheap bms from ali or should i use one from hilti tool packs. They are 36v and at least 30a cont...