Endless Sphere

Hello, I have a problem with my graphic equaliser and radio and was just wondering if anybody had any thoughts. http://i.ebayimg.com/images/g/pwwAAOSwNRdX5X8U/s-l1600.jpg Basically I am having trouble with the black wires. In the picture you see that it says "green - L", and "grey - R...

Hello, I have 3 x 3s lipo batteries wired in series and I want to balance charge them all at the same time. I know that I would need to buy a 10s charger...but when it comes to the balance boards or a 3 battery connector specifically for batteries wired in series I'm getting stuck. I know you can ge...

Thanks for the comments - I'll keep it in series then.

Hi, I'm planning on connecting 3 x 5000mah lipo batteries in series and in parallel. This is all dependant on the situation I find myself in though - for distance I will use parallel and for hills I will use series. Can somone please confirm that what I am doing is ok and that I won't end up blowing...

http://img.game.co.uk/ml2/2/0/5/4/205428_acc_b.png http://img.game.co.uk/ml2/2/0/5/4/205428_acc_b.png I'm trying to find a Nyko Kama Nunchuk to use with my 4.12 VESC. I have been searching all day/night online with no joy at all. They are as rare as hen's teeth. I live in the UK and I am finding it...

I had the 3 pin receiver plug in longways - Channel 2, 3 and 4.

I have a mini remote hand controller. When I switch the hand controller off the VESC lights up and starts turning the motor. :? all by itself. Just wanted to know what I'm doing wrong as this surely can't be right. While I'm here the sensitivity of the trigger is so fine with accelertion and braking...

Okay...can I start again please. On the video by http://vesc.net.au/ https://youtu.be/4XHODLiXaJY?t=213 he mentions that if you want to set the rpm limits of your motor you should times by 7 if you have 24 pole motor and times by 14 if you have a 28 pole motor. but there is no mention what to do if ...

Just found this: Re: OpenSource Remote for VESC ArduBoardControl Unread postby Pedrodemio » Tue Jul 05, 2016 3:15 am I've checked here, the pulse number that i said, i'ts the motor poles*3, for a 14 pole motor that gives 42 pulses per rotation. As i understand, that's the number of sequencial phase ...

.

I use a Neo RC C6364 245kv Brushless Outrunner ...and I would like to set up my VESC RPM limits. I know the engine RPM is 5439rpm what I need to know now is what do I times the rpm by as I have a 14 pole motor? http://acimg.auctivacommerce.com/imgdata/0/1/1/3/3/2/webimg/13732052.jpg As always many t...

GOT IT WORKING

I had to download fw v2.15 then v2.16 then v2.18. The bldc tool was not letting me go from v2.15 which was on the VESC straight to v2.18.

I think my problem is opposite to what you say...the firmware on the BLDC tool that I have downloaded is the latest fw 2.18 and I need to first find a 2.15 BLDC tool...then I can upload the latest fw to that once I am in.

Hello, I have a new VESC version 4.12 and I'm having problems uploading the firmware for it. Tried updating on the newest version of the bldc tool but it could not update due to the older firmware on my vescs...but on the screen grab below you will see that the "FW Upload Done" ...so why t...

Thanks for that dogman dan ...I think I found a clearer example of what I was trying to ask. pos&neg side.JPG The twin pack charge lead is basically made up of two 3s JST-XH ports soldered into place ...so the possibility of inserting the positive side 3s balance lead into the negative side (and...

Hi can anyone confirm that if I use a Twin Pack Balance Charge lead to balance charge 2 x 3s lipo batteries wired in series then I have to insert the 3s balance charge leads into the 6s connector in a certain way in order to avod shorting out the battery. 6s charge1.jpg So the battery with the main ...

Thanks for the response. Yes the batteries are connected in series. battery diag.JPG https://endless-sphere.com/forums/download/file.php?mode=view&id=197937 I can't work out where I'm going wrong. I have used this set up on two previous boards with no problems at all...!!! I've bought new twin p...

So with two 3s Lipos wired in series. Do I NEED to connect the 3s balance lead coming from battery with the main charge negative cable to the 6s balance port with the negative wire and connect the other battery 3s balance lead (with the main charge cable which would be positive), to the twin pack ch...

Hello, I've made an electric longboard. I'm having problems with smoke coming from the battery charger - even before the charger is pluged into the mains. On the outside of my board I have a 3-way DPDT switch, a 6s balance input socket, an XT60 socket and a voltage display. The 3 way switch is On/OF...

Hello, I have some questions regarding the USB port and the battery connections. I have a 2015 version 1.0 GT2B PCB and it would seem slightly different to the one in the pictures. My connector plugs on the CH3 PCB board are soldered firmly in place - I can't take them off as in the picture below. S...

Thanks Nordle for your reply and link. Appreciate it.
Alex.

Hi, I am about to order the 2 x 680 ohm resistors needed for the Badwolf v2 hand controller. Does it matter what the wattage is or can I use any 680 ohm resistor? I've seen them ranging from 0.5W all the way to 2W.
Thanks.

So on the motor specs it says Max Loading: 70A Now you go ahead and use 3S - the power needed to drag your ass along is exactly the same - so the motor now has to draw 90A. Am I right in saying that I am running the motor with my 3s set-up 20A over the recommended Max Loading of 70A ? So If I reconn...

I have been using HobbyKings Turnigy Aerodrive SK3 - 6364-245kv Brushless Outrunner Motor on my longboards. It says in the specs …Voltage: 10S Lipoly, Max Power: 2700W. My question is can anyone tell me what the motor wattage would be if used with 2 x 3s batteries wired in parallel and how do I work...

Hello, I have just made myself an electric longboard (here in the UK)... to cut a long story short, when I was out on my board last week I was asked to make 2 of them. The 2 buyers have paid and I'm now making the boards up for them. It has now come to my attention that I need product liability insu...