Search found 80 matches

by Johne-bike
Apr 05 2019 9:31am
Forum: E-Bike General Discussion
Topic: Factory Ebike for kids???
Replies: 7
Views: 344

Re: Factory Ebike for kids???

My daughter had this bike for her 8th birthday, 2 years ago. It is a Coyote Super Fat 20 with 1000w rear DD Hubmotor, KT 25amp controller, KT LCD3 display and 15ah 48v battery pack. Built by a small shop in Bangkok, Thailand and delivered to our home in Thailand. Cost is about 18,000 Thai baht compl...
by Johne-bike
Sep 06 2018 9:35am
Forum: E-Bike General Discussion
Topic: Hollowtech crankset and PAS
Replies: 6
Views: 471

Re: Hollowtech crankset and PAS

You are correct in that the crank arm fits tight against the bottom bracket and bearing, and if like mine there is also a hard rubber dust seal between the two. You do need to move the crank arm out a few mm's on the shaft to accommodate the magnet ring. To minimise the amount I needed to move the a...
by Johne-bike
Sep 06 2018 9:26am
Forum: E-Bike General Discussion
Topic: Hollowtech crankset and PAS
Replies: 6
Views: 471

Re: Hollowtech crankset and PAS

You are correct in that the crank arm fits tight against the bottom bracket and bearing, and if like mine there is also a hard rubber dust seal between the two. You do need to move the crank arm out a few mm's on the shaft to accommodate the magnet ring. To minimise the amount I needed to move the a...
by Johne-bike
Sep 05 2018 8:43am
Forum: E-Bike General Discussion
Topic: Hollowtech crankset and PAS
Replies: 6
Views: 471

Re: Hollowtech crankset and PAS

My Fatbike has a similar Crankset to the one you have. I am using a KT Kunteng KT-D12L PAS KIT, which is specially designed to be mounted on the left side crank. The 12 magnet ring is in 2 parts, and held together after fitting on the crank with a large spring steel clip. I have been using it for 2 ...
by Johne-bike
Aug 16 2018 3:38am
Forum: E-Bike Technical
Topic: Any throttles compatible with rapidfire or trigger shifters?
Replies: 15
Views: 1315

Re: Any throttles compatible with rapidfire or trigger shifters?

On my Fatbike, I have fitted a Wuxing half bar twist throttle on the right, then the Tektro hydraulic brake lever assembly is fitted tight next to this, then I have pushed the Shimano Rapid fire shifters as far left as possible, and trimmed a few mm's off the longer lever for extra clearance and it ...
by Johne-bike
Aug 11 2018 7:18pm
Forum: Stand-up E-scooters and E-skateboards
Topic: Building a adult “kickbike” “kickscooter” with only China parts. (Total noob)
Replies: 3
Views: 795

Re: Building a adult “kickbike” “kickscooter” with only China parts. (Total noob)

Thank you for your answer and contact details to AliExpress vendor! No problem.. Hope it helps you in your conversion plans! Jack at Speedless 1699 was fantastic when I was converting my Fatbike to electric power. My Thai / Taiwanese manufactured bike is fitted with some really nice Jinhua Powercir...
by Johne-bike
Aug 11 2018 7:19am
Forum: Stand-up E-scooters and E-skateboards
Topic: Building a adult “kickbike” “kickscooter” with only China parts. (Total noob)
Replies: 3
Views: 795

Re: Building a adult “kickbike” “kickscooter” with only China parts. (Total noob)

50Kph http://s.aliexpress.com/M3Ufua2U?fromSns I have researched building the same Alibaba Kick Bike. I was planning to use a Mxus 500w geared Hubmotor, with 100mm axle dropout width, which is the width of the Kick Bike rear dropout as I understand. This motor is listed as a bike Front Hubmotor for ...
by Johne-bike
Aug 09 2018 4:58am
Forum: E-Bike Technical
Topic: Cruise Control minimum engage speed LCD3 w/Kt Contoller
Replies: 11
Views: 523

Re: Cruise Control minimum engage speed LCD3 w/Kt Contoller

I have an all KT setup.. KT 45amp Sinewave controller, KT-D12L PAS kit, and KT LCD6 display driving a Mxus 3000w motor. The PAS locks in after the LCD6 shows 15kph or over. I have the wheel size set to 28" on my 26" Fatbike. My Daughter's 20" Fatbike is also an all KT setup, and the PAS also locks i...
by Johne-bike
Aug 06 2018 10:33pm
Forum: E-Bike General Discussion
Topic: Battery and electronic box, can you actually bend what you draw in sheet metal
Replies: 23
Views: 949

Re: Battery and electronic box, can you actually bend what you draw in sheet metal

Very nice box from PVC-pipe, how did you make the tabs to hold it together? The Tabs or brackets are also made from the very same 3mm thick, PVC water pipe, heat flattened cut to size, and heat formed to shape. I tapped 4mm threaded holes into the brackets, and use 4mm button head socket screws to ...
by Johne-bike
Aug 06 2018 10:26am
Forum: E-Bike General Discussion
Topic: Battery and electronic box, can you actually bend what you draw in sheet metal
Replies: 23
Views: 949

Re: Battery and electronic box, can you actually bend what you draw in sheet metal

make it out of a thermoplastic like polypropylene or HDPE... easy to cut out and you can fold it and shape it using a heat gun or heating element to soften it. We need a thread ond that. I'be been wanting to build a factory looking RIGID triangle frame box for long now. Metal is aesome but quite re...
by Johne-bike
Aug 05 2018 2:45am
Forum: Stand-up E-scooters and E-skateboards
Topic: Feedback on 3200W dual drive motor Scooter
Replies: 3
Views: 677

Re: Feedback on 3200W dual drive motor Scooter

I bought this dual 800w L8 scooter from Kerrywell via Alibaba, shipped to my home in Thailand. Complete with a 48v 20ah 18650 battery pack, full suspension, rear seat, led lighting, front and rear disc brakes, 10" wheels it was 750usd shipped to my door in Thailand. In addition, somehow the Shipper ...
by Johne-bike
Aug 05 2018 2:22am
Forum: E-Bike General Discussion
Topic: 18650 VS Lipo
Replies: 12
Views: 1198

Re: 18650 VS Lipo

There must be something in the water out here in the mid-atlantic (I'm in va) cause I was just at the local hobby store and bought a balance charger, cell checker, and parallel charging splitter. Almost bought the lipo cells from them also to support my local hobby store but just wasn't quite ready...
by Johne-bike
Aug 05 2018 1:24am
Forum: E-Bike General Discussion
Topic: Road bike hub motor - vendor recommendation (AliExpress)
Replies: 3
Views: 401

Re: Road bike hub motor - vendor recommendation (AliExpress)

Check out this recommended store on AliExpress. Find great products at low prices! http://s.aliexpress.com/e2AzuamI?fromSns I can completely recommend this store. Contact Jack and in my experience you will receive excellent advice and service with competitive prices on their range of ebike kits and ...
by Johne-bike
Jul 20 2018 9:48pm
Forum: E-Bike General Discussion
Topic: Fat Bike build 500W TSDZ2 Middle Motor
Replies: 34
Views: 3001

Re: Europe Netherlands 1st Fat Bike build Rear Dropout 220mm HUB?? VS Middle Motor??

120Kph fat bike 45H magenet V2 3000W brushless non-gear hub motor for electric fat bike or snow bike http://s.aliexpress.com/ZJRVFzUJ?fromSns=Copy to Clipboard This is the Link to the store on AliExpress where I purchased all of my ebike conversion kit. Jack at this store gives excellent service. Th...
by Johne-bike
Jul 20 2018 9:30pm
Forum: E-Bike General Discussion
Topic: Fat Bike build 500W TSDZ2 Middle Motor
Replies: 34
Views: 3001

Re: Europe Netherlands 1st Fat Bike build Rear Dropout 220mm HUB?? VS Middle Motor??

If you measure the rear dropout on your new Fatbike, I think you will find it is actually 190mm or 195mm spacing. This is the "normal" standard for Fatbikes? I have a Panther Hercules One Fat Bike, with 26" wheels, and a Coyote Fatbike with 20" wheels, sold in Thailand but manuctured in Taiwan, and ...
by Johne-bike
Jul 15 2018 1:51am
Forum: E-Bike General Discussion
Topic: Fat tires for class 3+ urban utility bikes?
Replies: 13
Views: 712

Re: Fat tires for class 3+ urban utility bikes?

I'm riding my Mxus 3000w Fatbike in Thailand on local roads, and hard pack gravel and dirt trails and regularly will cruise at 50kph very comfortably, with a lovely, smooth handling bike with no problems. My bike has 26" x 100mm rear rim, and 80mm wide front rim and now fitted with Chaoyang Sandstor...
by Johne-bike
Jun 29 2018 10:09am
Forum: E-Scooter and Motorcycle Photos & Videos
Topic: Kerrymotor L8 scooter and Zyao X12 Citycoco scooter
Replies: 2
Views: 877

Kerrymotor L8 scooter and Zyao X12 Citycoco scooter

<t>Decided to add a couple of electric scooters to our existing pair of Electric Fatbikes, for running errands and doing the school runs with our young daughter. Both the Kerrywell L8 Dual 800w scooter, with 48v 20ah battery, and the Zyao X12 dual 60v, 20ah battery were bought direct from the respec...
by Johne-bike
Jun 13 2018 10:04am
Forum: E-Bike General Discussion
Topic: Fat Tire E bike Conversion
Replies: 4
Views: 586

Re: Fat Tire E bike Conversion

My Mxus 3000w V2 4T powered Fatbike is a blast, and it is just comfortable, effortless performance with bulletproof reliability. I bought the Mxus laced into an exact replica of my OEM Fatbike rear wheel, with a Custom 190mm axle, accepting a 10 speed freewheel to match the bikes standard Shimano De...
by Johne-bike
May 04 2018 8:09am
Forum: E-Scooter and Motorcycle Photos & Videos
Topic: Kerrymotor L8 scooter and Zyao X12 Citycoco scooter
Replies: 2
Views: 877

New Kerrymotor L8 scooter

I live in Thailand and have been researching electric kick scooters for a while, particularly on Alibaba and Aliexpress, where I make nearly all my online purchases for a whole variety of products. I was looking for a well engineered scooter, with large capacity, 48v Li-ion 18650 cells, and around 1...
by Johne-bike
Mar 17 2018 4:01am
Forum: E-Bike Non-hub Motor Drives
Topic: My Bafang Ultra Mountain Bike! Frey AM1000
Replies: 1580
Views: 155707

Re: My Bafang Ultra Mountain Bike! Frey AM1000

We plan to make a fat bike version, we have made 2 samples. Will check the market demands quantity, then plan for production. 微信图片_20180314131507.jpg Electric bicycle still not popular in most of place in China. So It seems no big problem ride ebike in the bicycle ways. That looks great. I like the...
by Johne-bike
Mar 17 2018 3:48am
Forum: E-Bike Non-hub Motor Drives
Topic: My Bafang Ultra Mountain Bike! Frey AM1000
Replies: 1580
Views: 155707

Re: My Bafang Ultra Mountain Bike! Frey AM1000

Share a picture made by a photo below, how do you think about it? Not confident in English. Any good advice on the words? 微信图片_20180316193027.jpg Thank you Ivey for involving this community once more..! I agree that whilst I understand what you are getting at with your strap line, it does not trans...
by Johne-bike
Feb 16 2018 11:54pm
Forum: E-Bike General Discussion
Topic: Newbie looking for diy rear rack build ideas.
Replies: 70
Views: 3282

Re: Looking for a chromoly rear rack, any suggestions?

I've decided that chromoly is the way to go but I only know of a few different chromoly rear racks. Thinking some of you guys might be more knowledgeable about this and give me some more options as not much is coming up with my internet searches. Thanks. I am planning on purchasing this Steel rack ...
by Johne-bike
Feb 16 2018 11:43pm
Forum: E-Bike Build Threads / Photos & Video
Topic: Your Creation's Before & After Pics
Replies: 1828
Views: 594234

Re: Your Creation's Before & After Pics

Where do you get that carbon fibre vinyl wrap? I used black tape for some shiny parts that I could not get in the right color, but i like your solution better...I wish I would have the time to visit thailand again Hi, I purchased all my Carbon fibre 3D vinyl wrap from a vendor on the shopping site ...
by Johne-bike
Feb 16 2018 3:34am
Forum: E-Bike General Discussion
Topic: Front hub direct drive suitable for fatbikes?
Replies: 6
Views: 407

Re: Front hub direct drive suitable for fatbikes?

There are quite a few. Check it out on Aliexpress for instance. Mxus, Bafang, Mac and many others all make Hubmotors that will fit into 135mm dropouts. Just remember, they will work better with a non suspension front fork, and also fit some good Torque Arms. Personally, I think you would be better a...
by Johne-bike
Feb 11 2018 2:49pm
Forum: E-Bike Build Threads / Photos & Video
Topic: Your Creation's Before & After Pics
Replies: 1828
Views: 594234

Re: Your Creation's Before & After Pics

Hi Buk_ Thanks for liking! In fact, that right side picture actual shows the box that contains all the wiring connectors from the KT Controller, which is fitted adjacent to it on the left side! The Connector box is actually a large hardshell sunglasses box, covered in Carbon fibre vinyl wrap, and do...