Search found 24 matches

by Adamlivi
Dec 10 2018 6:19pm
Forum: E-Bike Technical
Topic: Bafang G310 geared hub - 11:1 reduction ratio!!!
Replies: 98
Views: 8966

Re: Bafang G310 geared hub - 11:1 reduction ratio!!!

Fellow ti ebiker. Ti is lovely and sweet. You should have zero issue with a 5 mm spread on your rear dropouts.
by Adamlivi
Nov 21 2018 1:26pm
Forum: E-Bike Reviews & Testing
Topic: Cycle Analyst V3 preview and first beta release
Replies: 4363
Views: 612968

Re: Cycle Analyst V3 preview and first beta release

...write failure at 2% with connection issue ... Any help or is this a "send in" repair? It's not bricked. No 'send in ' required. This is the comms problem referenced recently in this thread. The difficulty appears to be some very close timing issue in the Setup Utility 1.54 but we are sort of wor...
by Adamlivi
Nov 11 2018 5:01pm
Forum: E-Bike Technical
Topic: Bafang G310 geared hub - 11:1 reduction ratio!!!
Replies: 98
Views: 8966

Re: Bafang G310 geared hub - 11:1 reduction ratio!!!

I went with 30 NM on the G311 axle nuts based on Justin’s testing here: viewtopic.php?f=2&t=93562&hilit=Axle+nu ... &start=100
by Adamlivi
Nov 11 2018 11:47am
Forum: E-Bike Technical
Topic: Bafang G310 geared hub - 11:1 reduction ratio!!!
Replies: 98
Views: 8966

Re: Bafang G310 geared hub - 11:1 reduction ratio!!!

Anyone have the recommended axle but torque spec for this hub? Running on an aluminum fork so want to have maximum “bite”.
by Adamlivi
Nov 09 2018 3:08pm
Forum: E-Bike Technical
Topic: Bafang G310 geared hub - 11:1 reduction ratio!!!
Replies: 98
Views: 8966

Re: Bafang G310 geared hub - 11:1 reduction ratio!!!

Sooo... getting ready to install my G311 with a Phaserunner this weekend. Any suggestions on controller settings from the wizards of smart who have run this combo before is appreciated. Justin has suggested setting max phase current at 40 amps . what about other settings?
by Adamlivi
Nov 02 2018 9:02am
Forum: E-Bike Technical
Topic: Bafang G310 geared hub - 11:1 reduction ratio!!!
Replies: 98
Views: 8966

Re: Bafang G310 geared hub - 11:1 reduction ratio!!!

So, I'm setting up a G311 standard wind front hub with a Phaserunner (throttle only) and a 52v 6 ah Samsung 30q battery (one mounted and one spare) on my "pub bike". Currently have a tangent ascent with CA3 that I have become pretty comfortable programming but was hoping for the "secret sauce" setti...
by Adamlivi
Sep 26 2018 9:27am
Forum: E-Bike Non-hub Motor Drives
Topic: Dave's 80:1 RC mid drive kit build log
Replies: 1332
Views: 148314

Re: Dave's 80:1 RC mid drive kit build log

You may want to consider taking out a link... if too short adding a half link would make chain length perfecto. This was my solution. Just posting up my solution regarding some chain skipping/drop issues I had previously. Solution. I sourced a very long tooth profile narrow/wide derailleur cog. Put ...
by Adamlivi
Aug 04 2018 4:23pm
Forum: E-Bike Non-hub Motor Drives
Topic: Dave's 80:1 RC mid drive kit build log
Replies: 1332
Views: 148314

Re: Dave's 80:1 RC mid drive kit build log

What’s your front ring setup? Wheel size?
by Adamlivi
Aug 01 2018 8:02pm
Forum: E-Bike Reviews & Testing
Topic: Cycle Analyst V3 preview and first beta release
Replies: 4363
Views: 612968

Re: Cycle Analyst V3 preview and first beta release

Had similar issue. Look 1 page earlier and you’ll see Teklektic’s answer/solution for me.
by Adamlivi
Jul 31 2018 6:41pm
Forum: E-Bike Reviews & Testing
Topic: Cycle Analyst V3 preview and first beta release
Replies: 4363
Views: 612968

Re: Cycle Analyst V3 preview and first beta release

Hey Lightrush. I’m tracking with you. Tangent with a Sempu just added. Could you share your relevant tweaked settings on power and pas. I’m getting closer butthink you’re ahead of me on the learning curve.

Thanks in advance.
by Adamlivi
Jul 30 2018 11:11am
Forum: E-Bike Reviews & Testing
Topic: Cycle Analyst V3 preview and first beta release
Replies: 4363
Views: 612968

Re: Cycle Analyst V3 preview and first beta release

Would sharing my setting help?
by Adamlivi
Jul 30 2018 7:15am
Forum: E-Bike Reviews & Testing
Topic: Cycle Analyst V3 preview and first beta release
Replies: 4363
Views: 612968

Re: Cycle Analyst V3 preview and first beta release

I have a new Sempu as well on my Tangent 3210 with Phoniex Edge hv80 Esc and running latest CA beta. I also see higher input reading spikes with essentially no force applies, only crank rotation. Tends to occur after having applied strong crank force. I too ended up setting the starting force at aro...
by Adamlivi
Jul 28 2018 4:20pm
Forum: E-Bike Reviews & Testing
Topic: Cycle Analyst V3 preview and first beta release
Replies: 4363
Views: 612968

Re: Cycle Analyst V3 preview and first beta release

Worked!! You are a Rock Star Teklektik. Thanks!!!!
by Adamlivi
Jul 28 2018 9:01am
Forum: E-Bike Reviews & Testing
Topic: Cycle Analyst V3 preview and first beta release
Replies: 4363
Views: 612968

Re: Cycle Analyst V3 preview and first beta release

I just tried to update firmware to 3.12b1 and failed. Red screen cape up saying write failure at 2% with connection issue. left as is fr 5 min and then disconnected and restarted CA, it seems like it is now "bricked" with only a lit and textless screen when powerd up. Any help or is this a "send in"...
by Adamlivi
Jan 12 2018 1:53pm
Forum: E-Bike Non-hub Motor Drives
Topic: Dave's 80:1 RC mid drive kit build log
Replies: 1332
Views: 148314

Re: Dave's 80:1 RC mid drive kit build log

Rohloff is holding up very well. About 15,000 miles on it. a few hundred with the Tangent. If you do overload it, the fix a replacement of a pin designed to break under excessive load no a less then $100 repair.
by Adamlivi
Jan 12 2018 11:35am
Forum: E-Bike Non-hub Motor Drives
Topic: Dave's 80:1 RC mid drive kit build log
Replies: 1332
Views: 148314

Re: Dave's 80:1 RC mid drive kit build log

Just got on the list for the latest upgrade to Dave's awesome Tangent 3210 (http://tangentmotors.com/tangentsdrive) for my Ti/Rohloff urban assault e-bike! The new design looks pretty incredible and promises greater durability and reduced maintenance. https://scontent.fatl1-1.fna.fbcdn.net/v/t1.0-9/...
by Adamlivi
Nov 15 2017 1:48pm
Forum: E-Bike Non-hub Motor Drives
Topic: Dave's 80:1 RC mid drive kit build log
Replies: 1332
Views: 148314

Re: Dave's 80:1 RC mid drive kit build log

upgrade path ... reason number 127 why you rock Dave!!! Can't wait. You know how to reach me ;-)
by Adamlivi
Aug 30 2017 3:32pm
Forum: E-Bike Non-hub Motor Drives
Topic: Dave's 80:1 RC mid drive kit build log
Replies: 1332
Views: 148314

Re: Dave's 80:1 RC mid drive kit build log

You remain my ebike hero Dave!
by Adamlivi
Aug 10 2017 8:15pm
Forum: E-Bike Technical
Topic: On off switch battery
Replies: 12
Views: 896

Re: On off switch battery

I use this. Works very well. Great price from Luna
https://lunacycle.com/remote-on-off-solid-state-switch/
by Adamlivi
Mar 19 2017 11:10pm
Forum: E-Bike Non-hub Motor Drives
Topic: Quick drive by with my Nukeproof Tangent
Replies: 19
Views: 2193

Re: Quick drive by with my Nukeproof Tangent

Tangent does very well with torque PAS. Just built a 3000 watt with a Thun Torque BB. Cycle Analyst Handles it perfectly. Dave at tangent offers a complete torque pas package.
by Adamlivi
Feb 13 2017 4:46pm
Forum: E-Bike Reviews & Testing
Topic: Cycle Analyst V3 preview and first beta release
Replies: 4363
Views: 612968

Re: Cycle Analyst V3 preview and first beta release

Thanks Justin, very impressive work and love the dedication to the product... we all benefit. Just ordered my 2 button switch!
by Adamlivi
Jan 07 2017 9:26pm
Forum: E-Bike Technical
Topic: Power Switch
Replies: 23
Views: 2171

Re: Power Switch

I just ordered and received one of these for my 52v 17 ah pack going on my tangent ascent build......seems quality.
http://diyelectricskateboard.com/diy-el ... er-switch/
by Adamlivi
Jan 01 2017 4:09pm
Forum: E-Bike General Discussion
Topic: Best material for battery impact shock absorption?
Replies: 24
Views: 1521

Re: Best material for battery impact shock absorption?

I'm building an aluminum/carbon fiber battery box. Planning on trying inflatable padding via a 700c thornproof tube with presta valve protruding for inflation/deflation. I'll post pics if successful.