Search found 80 matches

by jpc6000
Jan 16 2019 12:56pm
Forum: E-Bike Technical
Topic: BBS02 not working no more
Replies: 16
Views: 720

Re: BBS02 not working no more

I have start the autotune from phaserunner I don't know Kv RPM/V for starting autotune so I guess and changed the RPM/V till it worked The program give then other Kv RPM/V I go back and start the autotune for 4 times then I get: phaserunner suite BBS02.png And the motor worked very good Now the moto...
by jpc6000
Jan 16 2019 12:37pm
Forum: E-Bike Technical
Topic: BBS02 not working no more
Replies: 16
Views: 720

Re: BBS02 not working no more

When the problems occur it's was raining mine first controller, it's was havy snowing maybe water seepage I have removed the silicone from controller and I see black powder on both side of the board 20190116_102818 (Middel).jpg 20190116_104046 (Middel).jpg 20190116_104149 (Groot).jpg 20190116_104648...
by jpc6000
Jan 16 2019 10:25am
Forum: E-Bike Technical
Topic: BBS02 not working no more
Replies: 16
Views: 720

Installing phaserunner BBS02

For configuration of the phaserunner
I need parameters for it RPM/V
Anybody know it?
by jpc6000
Jan 16 2019 9:52am
Forum: E-Bike Reviews & Testing
Topic: Grin Phase Runner / CA3 and BBSHD
Replies: 155
Views: 25477

Re: Grin Phase Runner / CA3 and BBSHD

I want to use phaserunner with BBS02
do anybody know parameters for tune this motor :?:
by jpc6000
Jan 15 2019 3:36pm
Forum: E-Bike Technical
Topic: BBS02 not working no more
Replies: 16
Views: 720

Re: BBS02 not working no more

I have try with other cable and other screens
by jpc6000
Jan 15 2019 12:27pm
Forum: E-Bike Technical
Topic: BBS02 not working no more
Replies: 16
Views: 720

BBS02 with phaserunner

The motor worked again good for some time then the problems start again the motor stopped working :cry: disconnect power, start up and worked again the I go for one large trip 100km I open throttle motor work, when I close throttle, when I open again motor do nothing then suddenly the motor work aga...
by jpc6000
Dec 30 2018 4:20pm
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

picture of e-bike
49065394_1044134605788233_1672095703943348224_n.jpg
by jpc6000
Dec 21 2018 2:43pm
Forum: E-Bike Technical
Topic: BBS02 not working no more
Replies: 16
Views: 720

Re: BBS02 not working no more

changed the controller and the motor worked again :D
20181221_203258 (Groot).jpg
this controller have done about 2000km and already broke, this is mine third! :mrgreen:
I shall try to change the condensor
by jpc6000
Dec 16 2018 3:47am
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

Justin from grin technologies write: "Be sure that you're seeing a difference between pins 3 and 4 on the PAS plug when shorting. Shorting to ground pin 3 should be the D arrow, and pin 4 should be the P arrow." That was wrong. I have changed the two wires. When I short pas now the P go down. :D But...
by jpc6000
Dec 15 2018 4:29am
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

I made screenshot about ca config
The screenshot was standard, I need read first
The program is not working very good, :cry: to attemp a lot of times before succeed

This is the config
CAconfig1.png
CAconfig2.png
by jpc6000
Dec 15 2018 4:08am
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

Grin says
If you just manually short the signal to Gnd you'll see it toggle down, correct?

When I shorten the signal
SETUP PAS DEVICE only D go up and down :cry:
by jpc6000
Dec 14 2018 7:52am
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

I have changed the resistor
Now it change between 0.97v and 3.42v
Setup pas device is still not pick up signal pas :?: :oops:
When I change more, it's more then 1V! :?
by jpc6000
Dec 13 2018 11:56pm
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

This is what Justin from grin technologies write about the problem

when moving cranck

pas / gnd switch between 0.782v and 2.4v


That's not really enough for a reliable digital signaling. Really you want <1V and >3.5V for proper logic level signalling. :idea:
by jpc6000
Dec 13 2018 9:27am
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

when moving cranck pas / gnd switch between 0.782v and 2.4v Pas shift / gnd switch between 4.29v and 1.4v Gnd and Speed/Dir 0.7v back and forwards nothing change Gnd and Torque 70mv back and forwards nothing change this is not the same what Daxxie messure! On the back of the print stays ZL1/ZL2/5V D...
by jpc6000
Dec 12 2018 1:46pm
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

I have ask Grin about the problem, they answer: In a pinch you can always just switch the P and D signals, since in principle only the P is needed for PAS to work. I'm not at all familiar with the actual sensor signal levels of that product, but a volt meter will tell you what is going on. You just ...
by jpc6000
Dec 11 2018 10:20am
Forum: E-Bike Technical
Topic: BBS02 not working no more
Replies: 16
Views: 720

Re: BBS02 not working no more

No, no picture of brake.
I disconnect the brake connection.
I think it is the controller.
I bought a new one. It seems that that the condenser is defect. It looks a bit Bol.
by jpc6000
Dec 10 2018 5:10am
Forum: E-Bike Technical
Topic: BBS02 not working no more
Replies: 16
Views: 720

BBS02 not working no more

lately I have the phenomenon regularly when I cut throttle, the motor refuse to start up again
when I switch off and on again, the motor start up again
today I have it again, but now the motor refuse to start up again!
Without any error on the screen.
I have change throttle but nothing changed :?:
by jpc6000
Dec 07 2018 4:02am
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

Hi I have made electric diagram
Bafang schema.pdf
(384.4 KiB) Downloaded 87 times
and a photo
20181207_095503 (Groot).jpg
by jpc6000
Dec 03 2018 8:51am
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

Torque sensor still not working :mrgreen:

Pas signal ok
20181203_135635_001 (Groot).jpg
but in CA setup pas device D go up and down but P not?
20181203_144650 (Groot).jpg
by jpc6000
Nov 15 2018 1:08pm
Forum: E-Bike Technical
Topic: CA3 3 position switch
Replies: 13
Views: 722

Re: CA3 3 position switch

the dig aux switch is better, so I shall remove these :lol:

https://www.youtube.com/watch?v=IU4qWSXtJUU
by jpc6000
Nov 15 2018 9:25am
Forum: E-Bike Non-hub Motor Drives
Topic: Bafang ultra upgrade to 2500watt
Replies: 87
Views: 13594

Re: Bafang ultra upgrade to 2500watt

pas not working I have change config ca to your info. But its not working? In config pas I see only second bar go up and down the other do not change! this is two wire torque pas, so something is wrong! :confused: PAS->SensrType identifies the interface as either 1-Wire (Dir) or 2-Wire (Dir+RPM). Pr...
by jpc6000
Nov 15 2018 8:36am
Forum: E-Bike Technical
Topic: CA3 3 position switch
Replies: 13
Views: 722

Re: CA3 3 position switch

I have also 2 button aux digital switch.
When I switch this on, I get only 2 pos switch on 3 pos switch!

When I switch aux dig off it works! :confused:

What is wrong?
by jpc6000
Nov 15 2018 4:01am
Forum: E-Bike Technical
Topic: CA3 3 position switch
Replies: 13
Views: 722

Re: CA3 3 position switch

the problem is not gone Pos 1 1.60V 31% PWR (good) 20181115_084852 (Groot).jpg Pos 2 2.42V 31% PWR (not good!) the first fault, pos two, that must be 66% :warn: 20181115_084904 (Groot).jpg Pos 3 4.98V 99% PWR (good) 20181115_084917 (Groot).jpg I gave set to 3 pos switch, and I get only two setups! 2...
by jpc6000
Nov 13 2018 3:52am
Forum: E-Bike Technical
Topic: CA3 3 position switch
Replies: 13
Views: 722

Re: CA3 3 position switch

I have tried with the orginal 3 pos switch
I get the same result
I think the config is wrong in the ca3
I'm study the manual, and changed the config
not good I think :oops:
can you give me what I have to change in config for aux 3 pos switch