Search found 11213 matches

by spinningmagnets
Apr 16 2021 7:00am
Forum: Battery Technology
Topic: Using a lead acid charger on a Lithium pack
Replies: 7
Views: 128

Re: Using a lead acid charger on a Lithium pack

It's best to charge lithium cells to 4.0V-4.1V, but its widely accepted that 4.2V per cell is the max.

4.2V x 13S = 54.6V as the absolute max voltage that pack should be charged to.
by spinningmagnets
Apr 16 2021 6:49am
Forum: EBike Non-hub Motor Drives
Topic: TSDZ2 750W no more powerful than 250W
Replies: 2
Views: 107

Re: TSDZ2 750W no more powerful than 250W

"...also haven't looked into settings yet..."

Change the max amps setting to something higher. Theres a chance that might have an effect.
by spinningmagnets
Apr 14 2021 6:04pm
Forum: EScooters/EMotorcycles
Topic: INDEX, motorcycle and scooter E-Conversions
Replies: 32
Views: 1357

Re: INDEX, motorcycle and scooter E-Conversions

https://www.facebook.com/photo?fbid=3980176128706403&set=pcb.2143146489156044 Peter Kovacs on Facebook (electric motorcycle builds) KTM 2016 EXC250 Motor, ME1507 Controller, ASI BAC8000 Battery, 20S / 22P Sony VTC5a, 72V https://scontent.fmci1-4.fna.fbcdn.net/v/t1.6435-9/p960x960/173227608_1015...
by spinningmagnets
Apr 14 2021 4:59pm
Forum: Health and Food
Topic: Looks like you really can get it all on Ali Express
Replies: 2
Views: 58

Re: Looks like you really can get it all on Ali Express

Looks like these are near the region of China that is like the Cajuns in rural Louisiana, they take pride in eating exotic meats that they catch...
by spinningmagnets
Apr 14 2021 10:01am
Forum: General Discussion
Topic: Lightweighting and aerodynamic optimization of a subcompact car.
Replies: 62
Views: 1032

Re: Lightweighting and aerodynamic optimization of a subcompact car.

One of the things I learned from the aero-Civic site was that the front grille creates significant drag. He covered the grille and found that the electric fan drew in enough air from below the engine to keep the engine temps safe. He installed movable louvers where the grill was, so he could manuall...
by spinningmagnets
Apr 14 2021 9:55am
Forum: General Discussion
Topic: Lightweighting and aerodynamic optimization of a subcompact car.
Replies: 62
Views: 1032

Re: Lightweighting and aerodynamic optimization of a subcompact car.

The most aero high speed velo's look like a raindrop with flattened sides, and it used cameras feeding a series of internal screens (*old smart-phones?) If passenger mirror deletion interests you, I'd reccomend a backup camera and right-side camera. They have gotten very cheap, and somebody's obsole...
by spinningmagnets
Apr 14 2021 7:32am
Forum: Motor Technology
Topic: Brushed vs brushless motor in go-kart setup
Replies: 12
Views: 278

Re: Brushed vs brushless motor in go-kart setup

Brushed motors have been over-volted about 50% without problems in the past. However, the higher the volts, the farther a spark can jump. Doubling the voltage throws off the timing. That means the phases are energized just a hair too soon and they stay energized just a hair too late. I suppose you c...
by spinningmagnets
Apr 13 2021 6:52am
Forum: Large EV General Discussion
Topic: Nobe 3-wheel EV car
Replies: 16
Views: 313

Re: Nobe 3-wheel EV car

$28,000, and if you want one there's a $2500 reservation fee.
by spinningmagnets
Apr 12 2021 10:17pm
Forum: EBike Troubleshooting
Topic: Accidental ebike newbie with controller and battery questions
Replies: 16
Views: 419

Re: Accidental ebike newbie with controller and battery questions

If you plan to actually haul cargo in that large cargo box, you would definitely be better served by a mid drive motor, so the motor has some gears to work with. The smallest I would use would be the 48V BBS02, and if you think you wouldn't get into trouble, a slightly larger 48V BBSHD would be idea...
by spinningmagnets
Apr 12 2021 11:53am
Forum: EBike Troubleshooting
Topic: Accidental ebike newbie with controller and battery questions
Replies: 16
Views: 419

Re: Accidental ebike newbie with controller and battery questions

If you add a temp sensor to the stator on the inside of the motor, you can run a surprising amount of watts through it, as long as it's only a temporary peak. The amps cause the majority of heat in a motor, and the motor you have can likely be run with 48V. That would give you slightly more power wi...
by spinningmagnets
Apr 10 2021 7:32am
Forum: EBike General Discussion
Topic: Belt + 3-speed IGH + Seattle Hills = TSDZ2, BBS02, BBSHD, or mistake?
Replies: 3
Views: 254

Re: Belt + 3-speed IGH + Seattle Hills = TSDZ2, BBS02, BBSHD, or mistake?

I don't know if it's a good idea or a bad one. For hill climbing, put on the smallest chainring that will fit on your selected drive unit. The fact you want to convert a belt drive complicates things. The TDSZ2 will climb very steep hills, but because it has less power than the other two you mention...
by spinningmagnets
Apr 09 2021 9:00pm
Forum: Large EV General Discussion
Topic: Nobe 3-wheel EV car
Replies: 16
Views: 313

Nobe 3-wheel EV car

https://mynobe.com/ The founder is from Estonia, which gained independence from Russia in 1991. Its an AWD vehicle using 3 hubmotors. It has a charger that takes 120V AC, and the suitcase sized battery is removable so it can be charged indoors, for those owners who dont have a garage. They claim 17...
by spinningmagnets
Apr 09 2021 11:32am
Forum: Motor Technology
Topic: How much silicone sealing harm heat transfer?
Replies: 3
Views: 144

Re: How much silicone sealing harm heat transfer?

I assume you are talking about using tubeless tires on a hubmotor. If yes, the edge sealant will not hurt heat in the motor.
by spinningmagnets
Apr 09 2021 9:46am
Forum: Battery Technology
Topic: Isolation between cells needed?
Replies: 4
Views: 284

Re: Isolation between cells needed?

The cells in the center of the pack will run hotter than the cells at the edge, which can passively shed "some" heat. This means the cells that are not on the edge will degrade sooner, and the pack will have reduced capacity when those cell degrade. As a general rule, I am not a fan of hot...
by spinningmagnets
Apr 08 2021 3:46pm
Forum: EBike Non-hub Motor Drives
Topic: Chain jamming between bbshd and Lekke chainring
Replies: 5
Views: 152

Re: Chain jamming between bbshd and Lekke chainring

You need a chain guide. Mountain bikers take big jumps and the chain bounces a lot. There are many choices and models available....
by spinningmagnets
Apr 08 2021 2:59pm
Forum: Motor Technology
Topic: Stator/magnet swept area
Replies: 8
Views: 268

Re: Stator/magnet swept area

If you confine yourself to radial-flux in-runners, like the popular Leaf 35mm, MXUS 45mm, and QS 50mm wide stator examples, I agree that swept face area is a good indicator of power potential, if all other factors are the same. (These three examples use the same 205mm diameter lamination stacks) The...
by spinningmagnets
Apr 08 2021 2:52pm
Forum: Motor Technology
Topic: Stator/magnet swept area
Replies: 8
Views: 268

Re: Stator/magnet swept area

The entire swept face of the rotor and stator of an axial-flux can be working magnets plus electro-magnet material, but the motor mass near the center has trouble shedding heat. If width isn't a problem, you can stack more stators and rotors on the same shaft. Zero motorcycles started out with Moten...
by spinningmagnets
Apr 08 2021 10:07am
Forum: Battery Technology
Topic: Battery charging basics
Replies: 14
Views: 481

Re: Battery charging basics

For a few years, one manufacturer called 14S lithium-Ion battery packs 50V. After the Bafang mid drives began growing in popularity, they were often used with 14S, and many began labeling the packs 52V. EGO-brand lawn tools call 14S 56V, and I think Echo calls them 58V. So which is it, and what char...
by spinningmagnets
Apr 08 2021 8:26am
Forum: Motor Technology
Topic: The HI-Lebowski: a Lebowski SMD brain running a zombified Honda IMA Inverter: *a HOW-TO guide*
Replies: 49
Views: 5689

Re: The HI-Lebowski: a Lebowski SMD brain running a zombified Honda IMA Inverter: *a HOW-TO guide*

I don't know why I havent seen this before. Brilliant work. It appears the Honda hybrid IMA controller is probably the perfect size for a street motorcycle E-conversion. I've been looking at conversions a lot recently, and the most common complaint is controllers. There's absolutely nothing availabl...
by spinningmagnets
Apr 08 2021 7:04am
Forum: EScooters/EMotorcycles
Topic: Observed trials bike designing
Replies: 113
Views: 9466

Re: Observed trials bike designing

Do you have any pics of the 2-speed gearbox internals?
by spinningmagnets
Apr 07 2021 9:13pm
Forum: Motor Technology
Topic: Axial Flux Reluctance motor, pondering DIY layout
Replies: 7
Views: 214

Re: Axial Flux Reluctance motor, pondering DIY layout

I don't recall where I first found that pic, or the company name... Found a paper (2016, I hadn't seen this before) with some info. Has a graphic of axial switched reluctance. https://www.intechopen.com/books/switched-reluctance-motor-concept-control-and-applications/switched-reluctance-motor-topolo...
by spinningmagnets
Apr 07 2021 7:29pm
Forum: Motor Technology
Topic: Axial Flux Reluctance motor, pondering DIY layout
Replies: 7
Views: 214

Re: Axial Flux Reluctance motor, pondering DIY layout

Thanks. Switched reluctance, four electromagnetic coils and four shared poles with no coils in them. Ten salinent poles on the rotor. This is a working model, and apparently well-regarded. Considered to be two-phase with two electromagnet pairs. https://www.electricbike.com/wp-content/uploads/2019/0...