Endless Sphere

It would be useful to have this info on the brake page in wiki. Thanks for the clear answer! I need some help from users with e-brakes. I did not find the info on wiki. I had to buy a new controller since mine is dead. I bought a 8 pin controller now that has throttle and ebrakes support. I use the ...

I need some help from users with e-brakes. I did not find the info on wiki. I had to buy a new controller since mine is dead. I bought a 8 pin controller now that has throttle and ebrakes support. I use the custom firmware with temperature sensor connected to the throttle, so I will use the throttle...

Hello. After about 1000 km, I have a problem with the torque sensor. At a standstill, with the pedals set horizontally without load, 192 shows once, after driving a few km 200, again after a few km 196, etc. the same is true when the pedal in a horizontal position loads its weight. Once I have 275,...

Hello, I had to buy a new controller since mine is dead. I bought a 8 pin controller now that has throttle and ebrakes support. I use the custom firmware with temperature sensor connected to the throttle, so I will use the throttle wires to solder the temp sensor. I do not use ebrakes. My question i...

Hello, Here is the pull request I did starting from Buba's code. It has the overrun fix and an additional fix for torque sensor with minimal value smaller than 100 so it does not give torque sensor error. https://github.com/leon927/TSDZ2-Smart-EBike/pull/2 You can build your binaries from my develop...

hello, I recommend that you post the problem on vlcd custom thread. With lcd3 you have a diagnostic screen where you can get some hints, but in this version i cant help. I had you similar problems in 2 situations: LCD cable crushed and power cable crushed. In both cases the ldc started but the assis...

Hi mbrusa, I plan to add the overrun fix to the LCD3 version. LE: I noticed in lcd3 thread taht you already did it :). But my question still stands. I noticed that in case of STANDARD_MODE there is // for overrun problem ui16_cadence_sensor_ticks_stop = (ui16_cadence_sensor_ticks + (ui16_cadence_se...

Hello guys! I have the same problem as Aja and Maximusdm. I have the ST link V2. When I try to connect to my XH18 unit (through the 6 pin cable, not directly on the unit, recpecting the connection sketch), I have the same message: "please check the swim cables etc..." on the STVP program (STM8S105x...

I have created a pull request on Buba's repository so this important fix does not get lost.

Hi mbrusa, I plan to add the overrun fix to the LCD3 version. LE: I noticed in lcd3 thread taht you already did it :). But my question still stands. I noticed that in case of STANDARD_MODE there is // for overrun problem ui16_cadence_sensor_ticks_stop = (ui16_cadence_sensor_ticks + (ui16_cadence_sen...

In sum, you need to give way more details of any issue you found so it can help me to understand and together we can workout a solution. I will rephrase. Let me know if you require more info. Torque sensor read idle is 35 units. With the unmodified software I get 2- torque sensor error and the moto...

Hello, I installed a new torque sensor. I calibrated it but if I set it around 110, the standby value is increasing steady in use until it reaches max torque sensor value or the range is max 30 units. In this case the motor no longer engages. I managed to make the value stable but the value on stand...

mbrusa wrote: ↑

Mar 12 2020 5:17am

Of course I will also put the source code, I am preparing the description, I seem to have been clear.

Thank you for taking the time and effort to add the change also to LCD3 version. This is highly appreciated!

Hello, I just replaced the torque sensor and performed the manual calibration. The 2 bolts on the sensor are well tight. I set it as it shows 125 units on standby and a max of 275. The problem is as I use the bike the standby value increases with each use. Now it is at 230. :( I did this process 2 ...

Hello, I just replaced the torque sensor and performed the manual calibration. The 2 bolts on the sensor are well tight. I set it as it shows 125 units on standby and a max of 275. The problem is as I use the bike the standby value increases with each use. Now it is at 230. :( I did this process 2 t...

buba wrote: ↑

Feb 23 2020 7:11pm

Long time, no buba...

Glad all is well! Can't wait to try some new things!

Really appreciate the answer! Can you please post some pictures with the custom tools? My problems are now only with the pull/push of the sensor to the frame. Hopefully this is the part of the puzzle you are missing, I worked out how to get the torque sensor out with the image below from the repair...

Hello, I need some ideas from people who installed/worked on the torque sensor. SO far I got the service manual from casainho and I have some clues. I will try to create a tutorial after I have a way of putting it back. How did you removed the torque sensor from the frame? I mean the actual torque ...

Hello, I need some ideas from people who installed/worked on the torque sensor. SO far I got the service manual from casainho and I have some clues. I will try to create a tutorial after I have a way of putting it back. How did you removed the torque sensor from the frame? I mean the actual torque s...

See here: https://github.com/OpenSource-EBike-firmware/TSDZ2_wiki/wiki/FAQ#Torque_sensor Thanks for the info. Things are clearer now. What I still do not know is how did the others press in the torque sensor while the inner ring is pressed by the small springs towards it. A lot of people worked on ...

Hi Elinx, I just made the calibration of the hardware sensor, thanks to Mbrusa I was able to read the ADC values, when empty it read 49.2 and 62.1 with the maximum force applied on the crank in a horizontal position, this calibration I did because having a reading field very narrow the engine had a...

My torque sensor died so I had to open it up. This is how It looks now, except that I repaid the broken wires. Still I have same error after assembly. With only the external ring connected I have no error, only with both parts in place. My questions are: 1. Is there any tutorial explaining how to di...

Thank you! :) I have a really good 52 V battery (maintains high nominal voltage for a long time) with a 52 teeth crank on a 36 V motor. Custom made bike with minimal resistance and really good tires. Using E-MTB exclusively as it does work well with my torque sensor. Depending on gearing, battery, ...

Hi Buba, It is good to see that all is well with you! That does not sound right. I am easily getting up to 50 kph without any problems. Be sure to check all the configuration parameters and let us know how it goes! Can you please add some details how are you getting to this speed easy? What assistan...

I have a similar problem with Adam. When I press walk assist the display shows 100W but the motor does not move. I also took it out. Without power I can move motor head easy. With power it is fix! Torque sensor diag works ok, also cadence and speed measurement. Just the motor does not move! I can h...