Search found 17 matches

by zeccato
Feb 09 2019 12:03pm
Forum: E-Bike Technical
Topic: Controller to limit PAS to 25kmh, Throttle unlimited
Replies: 15
Views: 282

Re: Controller to limit PAS to 25kmh, Throttle unlimited

My mention of the 22km/h is wrong, Today I measured max 15-16km/h of the pas, with about 100-180W continuous, and 250-299W peak, once per half a second was 390W. The throttle was 1200 peak. I think that with 2000W of thottle, you can get the pas to go at 25km/h (+ 3% allowed by law? = 27-28km/h lega...
by zeccato
Feb 08 2019 3:04pm
Forum: E-Bike Technical
Topic: Controller to limit PAS to 25kmh, Throttle unlimited
Replies: 15
Views: 282

Re: Controller to limit PAS to 25kmh, Throttle unlimited

The configuration of 48v. 16s life, 30A motor phase and 10A continuous, with swhx 24v. (2011) = 50kmh throttle, 30% pas = about 22kmh, and it gets softer, (and you can program a start delay to the pas). over 2000W with 25A continuous I broke the gears, and I don't know how far the pas gets, maybe 30...
by zeccato
Feb 08 2019 4:24am
Forum: E-Bike Technical
Topic: Controller to limit PAS to 25kmh, Throttle unlimited
Replies: 15
Views: 282

Re: Controller to limit PAS to 25kmh, Throttle unlimited

@zeccato: So you can set the speed limit independently for PAS and throttle for those EB3 controllers? That's right. Then I think you have to keep in mind how much W and speed you program with the throttle, and the pass adjusts separately up to a reduction of 30%, and up to 1500W peak (max 30A moto...
by zeccato
Feb 07 2019 9:11pm
Forum: E-Bike Technical
Topic: Controller to limit PAS to 25kmh, Throttle unlimited
Replies: 15
Views: 282

Re: Controller to limit PAS to 25kmh, Throttle unlimited

BTW, even if the CA does not have a way to limit the speeds separately, you cna just wire it so the throttle doesn't go thru the CA, but goes directly to the controller, paralleled (via diodes) with the CA's throttle output. Then the CA can limit the PAS in whatever way you like, while the throttle...
by zeccato
Feb 07 2019 8:23pm
Forum: E-Bike Technical
Topic: Controller to limit PAS to 25kmh, Throttle unlimited
Replies: 15
Views: 282

Re: Controller to limit PAS to 25kmh, Throttle unlimited

I think by just limiting the power, the motor would still be assisting above 25kmh (for example when pedaling or downhill). The idea is the following: To be legal there is no motor assistance at all allowed above 25kmh (at least in Germany). So PAS should work in a street legal way. Throttle would ...
by zeccato
Feb 07 2019 5:05pm
Forum: E-Bike Technical
Topic: Controller to limit PAS to 25kmh, Throttle unlimited
Replies: 15
Views: 282

Re: Controller to limit PAS to 25kmh, Throttle unlimited

Is there any controller (for lower power ebikes) which is capable of limiting speed to 25kmh when only PAS is active? When the throttle is engaged, the speed should not be limited at all. (for lower power ebikes) I'm not sure, but I see that you adjust the power and speed: on an em3ev controller ( ...
by zeccato
Feb 04 2019 3:49pm
Forum: E-Bike Technical
Topic: what do i need ? a better controller ?
Replies: 12
Views: 281

Re: what do i need ? a better controller ?

I have a 1500watt hub motor and I now have a 48V-11.6 dolphin battery on my bike. I thought I would get more speed than I'm getting now, could a upgraded controller help with more speed ? right now mine reads: DC MOTO CONTROLLER BY LITHIUM BATTERY VOLTAGE:DC48V BRAKES LOW LEVEL CURRENT 18A BOOSTER ...
by zeccato
Jan 21 2019 1:29pm
Forum: E-Bike Technical
Topic: How to connect pas etc. to Infineon EB3 Em3 ..?
Replies: 6
Views: 190

Re: How to connect pas etc. to Infineon EB3 Em3 ..?

amberwolf wrote:
Jan 18 2019 2:42am
wrote:
Jan 18 2019 2:14am
I:.............
Perhaps you already know:
The topic was solved in this thread:

Thank you, greetings.

https://endless-sphere.com/forums/viewt ... 4#p1440254
by zeccato
Jan 21 2019 1:14pm
Forum: E-Bike Technical
Topic: Adding PAS to EM3EV controller
Replies: 17
Views: 926

Re: Adding PAS to EM3EV controller

NeilP wrote:
Jan 21 2019 10:05am
I'd probably wire the PAS to these.
+5v red
GND 6 to black
TA to the other one
Screen Shot 2019-01-21 at 15.03.53.png
Thank You so much, especially NeilP,
it works, too with the USB software program.

Tomorrow I will solder the wires.
by zeccato
Jan 21 2019 9:02am
Forum: E-Bike Technical
Topic: Adding PAS to EM3EV controller
Replies: 17
Views: 926

Re: Adding PAS to EM3EV controller

I f you want to open your controller and look, you might be lucky... If it happens to be labelled PAS, then you'd need to solder a wire to that pad, and another from a 5 volt feed and another to ground Get it wrong and you will of course risk screwing the controller on that controller it was labell...
by zeccato
Jan 19 2019 10:29am
Forum: E-Bike Technical
Topic: Adding PAS to EM3EV controller
Replies: 17
Views: 926

Re: Adding PAS to EM3EV controller

...................... 2 GND / 3 Shunt -ve 4 Shunt + ve 5 Speed ​​Signal 6 Throttle signal Thank you so much, Em3ev said: [ The PAS display/controller that we offer connects directly to the CA plug. It doesn’t connect to the throttle connecto r ]. I have one display (see photo) that looks identical...
by zeccato
Jan 18 2019 2:22pm
Forum: E-Bike Technical
Topic: Adding PAS to EM3EV controller
Replies: 17
Views: 926

Re: Adding PAS to EM3EV controller

Too long ago to remember But any PAS with 3 wires will be basic Voltage in. Probably 5 volts Ground Signal out Thanks, but it's still not enough, one told me that if I'm wrong I could do damage, the socket of the controller where I should connect the 3 wires of the pas is this: 1 Battery Voltage Vc...
by zeccato
Jan 18 2019 1:08pm
Forum: E-Bike Technical
Topic: Adding PAS to EM3EV controller
Replies: 17
Views: 926

Re: Adding PAS to EM3EV controller

NeilP wrote:
Jul 26 2014 7:15am
Looks like a standard hall sensor ring , ...........
Hi, did you discover the connection of the 3 wires of the pas? I have a similar pas, and controller eb3 12 fet em3ev ,.
Thank you when you reveal it,
the mystery continues here too ',
I looked everywhere = 0.
by zeccato
Jan 18 2019 3:25am
Forum: E-Bike Technical
Topic: How to connect pas etc. to Infineon EB3 Em3 ..?
Replies: 6
Views: 190

Re: How to connect pas etc. to Infineon EB3 Em3 ..?

I would like to connect the 3wires pas, to the wires of the 6 pin C.A. of the controller to test, which wires do I connect to? (controller 6 pin): Unfortunatley, as I already said, you can't. It wont' work. It can't work, because there is no signal from that PAS unit that can tell the controller an...
by zeccato
Jan 18 2019 2:14am
Forum: E-Bike Technical
Topic: How to connect pas etc. to Infineon EB3 Em3 ..?
Replies: 6
Views: 190

Re: How to connect pas etc. to Infineon EB3 Em3 ..?

If your controller did not come with PAS, it may not have a connector for it. ........................... Thanks, the pas has 3 wires, with magnets. I have usb software. I would like to connect the 3wires pas, to the wires of the 6 pin C.A. of the controller to test, which wires do I connect to? (c...
by zeccato
Jan 17 2019 9:01am
Forum: E-Bike Technical
Topic: How to connect pas etc. to Infineon EB3 Em3 ..?
Replies: 6
Views: 190

How to connect pas etc. to Infineon EB3 Em3 ..?

It seems to me that the pas can connect directly to the control unit (true?) (to the 6-wire connector of the AC (or display) of the control unit, (is in the middle see photo): 1 Battery Voltage Vcc-L (red (I think it's battery indicator, my 48v., and I do not need to use it) 2 GND / Shunt + ve (blac...