Search found 232 matches

by Elinx
May 31 2020 10:17am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

.... when i press the light button, it shows E02 when i di a double klick it goes to E03 then normally as the manual says if i press tge light button one time, it should show the battery Voltage, correct?.... It all depends what you have setup by default and what you try to do, modify parameters or...
by Elinx
May 30 2020 6:04pm
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

..........bit i cant get the configurator to connect, or is there a special way to change the settings with tge configurator? You can't change settings afterwards with the configurator wihout flashing. I don't understand what you have done. Before , you said you have flashed the contoller already. ...
by Elinx
May 30 2020 7:13am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

How can i flash the display? ........ One of the advantages is you don't need to flash the stock display, but only the controller. If you have flashed the controller, you can use OSF right away. For handling the display you need the Display operation manual Because the OSF operation has changed fro...
by Elinx
May 26 2020 11:53am
Forum: E-Bike Non-hub Motor Drives
Topic: tsdz2 Battery
Replies: 2
Views: 109

Re: tsdz2 Battery

cavi wrote:
May 25 2020 6:44pm
alot of info would be nice, ........
See here too
I aks there also for more information, but nothing more than this 78 cells (13S6P):
intbattsmall.jpg
intbattsmall.jpg (12.36 KiB) Viewed 50 times
by Elinx
May 26 2020 10:37am
Forum: E-Bike Non-hub Motor Drives
Topic: flexable open source torque sensor calibration for TSDZ2
Replies: 4
Views: 89

Re: flexable open source torque sensor calibration for TSDZ2

cavi wrote:
May 25 2020 5:49pm
... then I need 6 other weight things, ....
For the other weights you can use a simple lugguage scale
Instead of pushing the front pedal you pull the back pedal if the cranks are horizontal.
by Elinx
May 24 2020 11:00am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

stancecoke wrote:
May 24 2020 5:21am
..... you can access every single commit on github........
Thanks for that. I wasn't aware of this before
by Elinx
May 24 2020 2:31am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

...... Therefore I reversed to latest version "mb.20beta1.A" using the git history and checking out to the latest workable version of Stancecoke ($ git checkout 17a3649) .......... Accessing github's archives that way, is an interesting option I didn't aware of, thanks. I understand why it isn't, b...
by Elinx
May 23 2020 4:13am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

...... Also does the motor heat up more after installing the OSF or does that happen with the stock firmware as well. When I have ridden the bike I feel the motor - and while it is warm it has never been unreasonable hot. That was after riding at speed and tour modes and occasionally turbo up hills...
by Elinx
May 20 2020 5:02am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

Yes, you have to unzip the latest version and then you can launch the configurator with the command line java -jar JavaConfigurator.jar and it will create the config.h under the subdirectory src/controller by clicking on "Compiling and Flash" button. It will work also on OS/X and Linux........... T...
by Elinx
May 19 2020 5:44pm
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

...... I don't understand is how do I turn on the grey Java configurator that everyone keeps taking pictures of so I can put the settings in. I was under the impression that you were already one step further and wanted to know the function of the parameters. For this question, I refer to the wiki ,...
by Elinx
May 19 2020 1:01pm
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

...After doing another 100miles on my new settings i thought i'd share just in case people were interested in riding the way i do .. Thanks for your feedback. But, now you have tried and configure the assist settings, can you answer your own question you did before . ..... 3 - are these power assis...
by Elinx
May 18 2020 5:30pm
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

TSDZ2 Parameter Configurator 2.0 OSF mb.20beta1.B Where do I find this ..... I think you mean the configuration manual for the Java configurator. You find the manuals on mbrusa's github repo , together with the OSF and the configurator. There are three manuals, in two languages (EN-IT), for mb.20be...
by Elinx
May 15 2020 5:52pm
Forum: E-Bike Non-hub Motor Drives
Topic: Hardware temperature control tsdz2
Replies: 102
Views: 11676

Re: Hardware temperature control tsdz2

silentguy wrote:
May 13 2020 9:12am
Doesn’t it leak out ?
Any chance of Fire ?
NexusG didn't mentioned fire, but he talks about some leakage

"There's a small leak on the right side of the motor but this is because I didn't add silicone in the casing to prevent oil going from the left to the right side of the motor"
by Elinx
May 13 2020 8:57am
Forum: E-Bike Non-hub Motor Drives
Topic: Hardware temperature control tsdz2
Replies: 102
Views: 11676

Re: Hardware temperature control tsdz2

NexusG has filled up entirely TSDZ2 with car engine oil for cooling purpose. "It runs well and much quieter, even if I have a brass gear ! The oil plays both the role of coolant and lubricant................. .........It doesn't avoid the increase of oil temperature at continuous high power (I was ...
by Elinx
May 13 2020 3:45am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

... what exactly EMTB mode is. ..... ...maximum recomended values for motor acceleration somewhere close to the stock FW motor acceleration? ..... I never use it (cylcle only on roads), but it is a more dynamic mode with a wider range. This what the wiki writes about emtb. Emtb "mode automatically ...
by Elinx
May 12 2020 4:32pm
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

..... Thanks so much for the detailed reply. Regarding point 1 what would be your recommended settings. Keeping 16a and upping max power to 480w??? (I did notice the peak power was less than factory setting with the 250w setting cycling this morning, though I usually ride on eco so only noticed wit...
by Elinx
May 12 2020 12:59am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

emr wrote:
May 11 2020 5:54pm
.....

The link to the 'wiki' ..........page no longer works...
...
That is because stancecoke has removed his tsdz2 repo
And mbrusa forgot to copy that wiki to his repo.
So hopefully is that wiki somewhere and can add mbrusa this to his active repo

edit: Wiki is visible again
by Elinx
May 11 2020 4:34pm
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

... I've got the 250w 36v motor version but have a few little questions.......... 1. --This motor has a hardware limited current of 18A (750Wmax. full batterie), but a lower current is better for less heat. You have setup 16A max. current, with lowest batterie Voltage of 30V, 30x16= 480W max. 250W ...
by Elinx
May 08 2020 11:51am
Forum: E-Bike Non-hub Motor Drives
Topic: New "TSDZ2 Torque Sensor Central Motor"
Replies: 7270
Views: 758838

Re: New "TSDZ2 Torque Sensor Central Motor"

Hello. Could someone tell why my motor start having a little wobble ......How to repair? That wobble is a wellknown problem of this motor with Chinese tolerances. The axle is a bit too thin for the bearings. Here I have shared some links for a solution, with adding a second bearing and some thin me...
by Elinx
May 07 2020 6:20pm
Forum: E-Bike Non-hub Motor Drives
Topic: Hardware temperature control tsdz2
Replies: 102
Views: 11676

Re: Hardware temperature control tsdz2

... Probably not the cheapest way to go but a number of these and then also the silicone padding seem like would be a good solution even this might work, ....... imho finns are not always necessary There are enough experiences that the temperature is more controlled down with easy filling the airga...
by Elinx
May 07 2020 5:07am
Forum: E-Bike Non-hub Motor Drives
Topic: Tongsheng crank wobble - can I use Loctite?
Replies: 9
Views: 500

Re: Tongsheng crank wobble - can I use Loctite?

..... but not up/down,............ For left/right you can use washers. For up/down: You can insert a second bearing behind the dustcap (arrow). On the other side (circle) you can fill the space between axle with 0.07mm metal sheet (like from a cheap feeler gauge). I know steel is not the best mater...
by Elinx
May 06 2020 4:24am
Forum: E-Bike Non-hub Motor Drives
Topic: Hardware temperature control tsdz2
Replies: 102
Views: 11676

Re: Hardware temperature control tsdz2

colsaunders2 mentioned here another solution by filling the gap with silicone thermal putty. No results yet " I decided to try silicone thermal putty (TG-PP10). 50 grams is only $30 and is just enough to fill the gap between the stator midsection and the side cover. The excess putty squeezed right ...
by Elinx
May 06 2020 3:47am
Forum: E-Bike Non-hub Motor Drives
Topic: New "TSDZ2 Torque Sensor Central Motor"
Replies: 7270
Views: 758838

Re: New "TSDZ2 Torque Sensor Central Motor"

...... Can I have links to your silicone pad and aluminum fins? If you read a bit further you can see that he used cheap 2mm pads of Ebay. The aluminium finns are bended and glued heatsinks You can find also a lot of solutions and links in the " Hardware temperature control tsdz2 " topic I have tri...
by Elinx
May 05 2020 7:57am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1123
Views: 116937

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

...... The previous one will no longer be updated. I also added the link in signature. I read "the higher cadence option by field weakening", very interesting.......... I think I'm looking at us. Not immediately, because after two months locked in the house, ............ Hi mbrusa. A bit confusing,...
by Elinx
May 05 2020 7:31am
Forum: E-Bike Non-hub Motor Drives
Topic: New "TSDZ2 Torque Sensor Central Motor"
Replies: 7270
Views: 758838

Re: New

andrewgateway wrote: .....
I have a 48v 250w....
I think this is a 48V " overdrive" version with modified stock FW, so you can use 48V battery on a original 36V 250W motor.