Search found 981 matches

by Elinx
Sep 27 2022 11:52am
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

I wonder why I write the manuals. ..... Thank you . When you explain it becomes clear immediately. .....Sometimes though we just need to see it again to make it clear... ... mbrusa is right. It cost a lot of time and efforts to write these manuals. If something isn't clear I can imagine that there ...
by Elinx
Sep 27 2022 11:37am
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1844
Views: 248210

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

Per la prima domanda trovi la risposta qui. https://endless-sphere.com/forums/viewtopic.php?f=30&t=110682&p=1734072#p1734072 Per la seconda, forse hai lasciato il limite di potenza in Street mode a 250W. :) For the first question, find the answer here . For the second, you may have left the...
by Elinx
Sep 27 2022 11:24am
Forum: Motor Technology
Topic: tsdz2 OSF torque assist setup
Replies: 4
Views: 123

Re: tsdz2 OSF torque assist setup

.... i thought that its could have been more clear if different questions has different topics so it would be easier to browse them , not to scroll gazillion pages of single topic...... NO , it isn't, because if you want to find something it is easier to use the advanced search mode in a certain to...
by Elinx
Sep 22 2022 10:12am
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

.... Eats well on the throttle..... ... if the cadence sensor falls off, will the motor stop assisting? If throttle does work, the blue gear can't be the problem, the spragclutch still can. If the PAS sensor is defective, the motor doesn't run too. But if the PAS sensor is defective the fault is pe...
by Elinx
Sep 21 2022 3:13am
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

Atrihalov wrote:
Sep 21 2022 2:46am
...I think it's probably the torque sensor..... calibration of the torque sensor,..values .....are from 146 to 330.
If this are the values of the torquesensor, then imho there is nothing wrong with it and must there be another reason.
Maybe the blue gear or spragclutch could be the reason.
by Elinx
Sep 15 2022 5:22pm
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1844
Views: 248210

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

.... often happens to me that after switching on, one part of the battery is displayed and the engine does not run......TSDZ2_Controller_vM0.19.C_and_TSDZ2_Configurator_0.3.7_con_codice_0.19_Stable I see you had this problem already april 2020 . What is done in between till now? The 0.19 version yo...
by Elinx
Sep 14 2022 6:52am
Forum: EBike Non-hub Motor Drives
Topic: New "TSDZ2 Torque Sensor Central Motor"
Replies: 9515
Views: 1142633

Re: New "TSDZ2 Torque Sensor Central Motor"

ancan wrote:
Sep 14 2022 6:43am
Elinx wrote:
Sep 14 2022 6:39am
... this post ....
Yes correct, ...
For decreasing some of the play of the spider and cranks you can add some extra bearings.
It isn't perfect, but imho better than without them.
by Elinx
Sep 14 2022 6:39am
Forum: EBike Non-hub Motor Drives
Topic: New "TSDZ2 Torque Sensor Central Motor"
Replies: 9515
Views: 1142633

Re: New "TSDZ2 Torque Sensor Central Motor"

ancan wrote:
Sep 14 2022 5:00am
I all! I posted earlier about my bike making squeaking sounds, but didn't get any replies ....
If you mean this post from 11 months ago?
I have replied you the same day there
by Elinx
Sep 11 2022 6:44pm
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

hermes127 wrote:
Sep 11 2022 5:23pm
..... restart pedalling the motor is not responding (it's apparently off) so I have to pedalling backwards for 1 or 2 turns for having the motor assisting again.....
This looks the same problem like here
by Elinx
Sep 07 2022 4:29am
Forum: EBike Non-hub Motor Drives
Topic: TSDZ2 problem - pedals spin freely, not engaging with gear
Replies: 14
Views: 453

Re: TSDZ2 problem - pedals spin freely, not engaging with gear

... So rather than remove them to clean, I just inspected everything and reassembled, then cleaned the whole sprag clutch with solvent, then repacked with grease. ... :bigthumb: Thanks for your illustraded "howto" When I read your description I remember that Wapous did this service too a ...
by Elinx
Sep 07 2022 4:07am
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

.... not actually installed the display would read ~15 degrees. And testing the throttle voltage pin on the board gave a resting voltage of 0.15. ..... Personally I have no experience with adding a temperature sensor, but know there could be a problem with hardware. Look here if this is maybe for y...
by Elinx
Sep 06 2022 5:39pm
Forum: EBike Non-hub Motor Drives
Topic: TSDZ2 problem - pedals spin freely, not engaging with gear
Replies: 14
Views: 453

Re: TSDZ2 problem - pedals spin freely, not engaging with gear

TSDZ2_v1_and_v2-main_gear-v2_broke_bearing.jpg This is a pic from Github, not my actual bearing. Yes that is the maingear with the spragclutch inside. You can replace the complete maingear or only the spragclutch . The maingear could have straight teeth and helical teeth. I think you have helical t...
by Elinx
Sep 06 2022 3:24pm
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

.... I can see my current use going up and down with each pedal stroke (example: right pedal 8 amps, left 4 amps). ... When I turn Calibration to 'disabled', this problem seems to go away. It produces a bit less power .... In addition to see this fluctuated data on your display, do you also notice ...
by Elinx
Sep 06 2022 9:07am
Forum: EBike Non-hub Motor Drives
Topic: tsdz2 36v actual power ?
Replies: 10
Views: 392

Re: tsdz2 36v actual power ?

I was thinking if I can get same assist from 36v motor as I have from 48v motor . mostly because of small room in frame that makes me wonder if 10s4p would be better than 13s3p . is there only benefit from buying 36v motor and feeding 48v into it ? wouldn't it heat more? Between 13p3p and 10s4p the...
by Elinx
Sep 06 2022 6:11am
Forum: EBike Non-hub Motor Drives
Topic: TSDZ2 problem - pedals spin freely, not engaging with gear
Replies: 14
Views: 453

Re: TSDZ2 problem - pedals spin freely, not engaging with gear

jeffieh wrote:
Sep 06 2022 1:25am
...Sometimes (and it's usually just after changing up) the cranks spin freely instead of engaging with the motor gear. It's a completely 'clean' spin ....
There could be different reasons like.
Sprag clutch, Blue gear slipping, Fail PAS
by Elinx
Sep 06 2022 3:04am
Forum: EBike Non-hub Motor Drives
Topic: tsdz2 36v actual power ?
Replies: 10
Views: 392

Re: tsdz2 36v actual power ?

..... With the same current the 36V version definitely outputs less power than the 48V version. ..... won't the 36V motor be able to handle a higher current before overheating? I read back and I see what your mean. I don't know why I mentioned a difference with thickness :oops: (I have edit my post...
by Elinx
Sep 05 2022 5:58pm
Forum: EBike Non-hub Motor Drives
Topic: tsdz2 36v actual power ?
Replies: 10
Views: 392

Re: tsdz2 36v actual power ?

pxl666 wrote:
Sep 05 2022 4:07pm
...36v version running 10s will have same mechanical power as 48v version at 13s . ....
No, the 48V use more elektrical power with the same current.
More electrical power gives more mechanical power.
by Elinx
Sep 05 2022 1:09pm
Forum: EBike Non-hub Motor Drives
Topic: tsdz2 36v actual power ?
Replies: 10
Views: 392

Re: tsdz2 36v actual power ?

pxl666 wrote:
Sep 05 2022 11:41am
...... do you think that 36v version of tsdz2 will have same torque as 48v version ? at full charge of course
I never have tried, so I really don't know.
But by redenation I think for torque it makes no difference, but you will feel max. power earlier.
by Elinx
Sep 05 2022 10:19am
Forum: EBike Non-hub Motor Drives
Topic: tsdz2 36v actual power ?
Replies: 10
Views: 392

Re: tsdz2 36v actual power ?

.... does anyone know if tsdz2 48v will have same mechanical power when powered with 36v ? if there will be more current or if it will have less torque ? There are two Tsdz2 versions 36V 4000rpm and 48V 4000rpm. The difference is 48V has more (but thinner?) windings. A 36V battery delivers power be...
by Elinx
Sep 05 2022 9:21am
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: Which TSDZ2 OSF for stock Enerdan SW102?

..... Casainho's builds are for custom flashed displays only, mbrusa firmware to use for stock rom displays . mbrusa has several firmware for stock and custom flashed displays ... release .. notes state: "With newer displays P860C, 850C, P850C, SW102, it may not work." Apparently that not...
by Elinx
Sep 05 2022 5:10am
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: Which TSDZ2 OSF for stock Enerdan SW102?

My 2019 36V TSDZ2 with KM5S-LCD supports good when cold. Reduced support is always experienced after cycling 15-30 minutes, despite a steady 42.1V and >1000 Wh battery. Currently the display pops error 30. That is why I am looking at OSF options. I'd wish to use a "stock" Enerdan SW102 . ...
by Elinx
Sep 04 2022 3:34pm
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

..... I have enabled temperature sensor in the basic settings. Yet despite this it is cycling through the same 3 values. I am at a loss what to try. ... 5 seconds. On my screen it is much quicker each data only displays for a second or less. From the manual "By default 2 data are displayed, 1 ...
by Elinx
Sep 04 2022 4:40am
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

...battery %. Now it is showing 95.7 .... dont see any apparent changes. Pressing lights on results in E02 followed by 3 values cycling over and over. I have installed a temperature sensor and am trying to display this value to test the functionality. With flashing OSF your display will not have an...
by Elinx
Sep 03 2022 1:24pm
Forum: Motor Technology
Topic: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18
Replies: 1844
Views: 248210

Re: Tsdz2 firmware open source adapted to vlcd5, vlcd6 and xh18

... CMD window open were the batch files pointing to wrong folders for the compiler and ST tools. It also took me a while to realise that if I clicked on a default ini file in the Java configurator, those parameters would be used. Could that be what happened maybe? Every time if you hit "compi...
by Elinx
Sep 03 2022 1:06pm
Forum: Motor Technology
Topic: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.
Replies: 1548
Views: 94173

Re: TSDZ2 OSF for all displays, VLCD5-VLCD6-XH18, LCD3, 860C-850C-SW102.

.... I do see 99.9 when the display is powered on, but none of the setting selected in the configurer seem to be active. You have flashed OSF. If you have flashed most default settings, you haven't enabled "set parameters at startup" You can do this by: Assist level 0 (zero) push 2x light...