Endless Sphere

It has been a while since I have been here. I have now done around 1300km using the OSF with VLCD 5 on my Cannondale Scalpel and overall it is very good. I bought a Cube Reaction Pro with Bosch motor for my wife recently but she prefers my bike :-) . With the firmware, power level 3 (emtb) does not ...

Got my SW102 from pswpower today. Do I still need to cut it open to flash / update bootloader and firmware or can it be done via bluetooth. Recall reading that bluetooth was on the way. Follow the wiki instructions. Thanks, I thought I read that it would / might be possible to do it without cutting...

Got my SW102 from pswpower today. Do I still need to cut it open to flash / update bootloader and firmware or can it be done via bluetooth. Recall reading that bluetooth was on the way.

I read the motor controller can be enabled by simple connect green wire to white wire and this way there is no need to use LCD here https://opensourceebikefirmware.bitbuck ... oller.html So joinging Green P+ battery voltage to White Vin / ground should enable the motor without the LCD, however with...

I have been trying trying to run a new TSDZ2 with no display, have flashed firmware and settings using the configurator with default emtb mode. I thought is was as simple as joining the blue battery + V wire to the red Vin wire but dies not work. I ended up installing standard 52v firmware and was ...

I read the motor controller can be enabled by simple connect green wire to white wire and this way there is no need to use LCD here https://opensourceebikefirmware.bitbuck ... oller.html So joinging Green P+ battery voltage to White Vin / ground should enable the motor without the LCD, however with...

I have been trying trying to run a new TSDZ2 with no display, have flashed firmware and settings using the configurator with default emtb mode. I thought is was as simple as joining the blue battery + V wire to the red Vin wire but dies not work.

Anyone here had any success running the TSDZ2 without an LCD ? I have been trying but no luck as yet. Below is my post from another chapter of endless. Need some help. I flashed the firmware in my new motor today and made necessary settings using marcoqs java configurator. I am waiting on my SW102 a...

Need some help. I flashed the firmware in my new motor today and made necessary settings using marcoqs java configurator. I am waiting on my SW102 and have read that you can power the motor by joining white to green. I gave the 8 pin plug from the motor the chop and joined the white and green but n...

Need some help. I flashed the firmware in my new motor today and made necessary settings using marcoqs java configurator. I am waiting on my SW102 and have read that you can power the motor by joining white to green. I gave the 8 pin plug from the motor the chop and joined the white and green but n...

Does anybody have the pinout showing colors for the plug on the SW102 to save me cutting my loom open ? I used a bafang wiring harness for the breakout cable side and just the 8 pin connector side that came with the motor. I soldered the 8 wires together for a custom length harness that was just ri...

Need some help. I flashed the firmware in my new motor today and made necessary settings using marcoqs java configurator. I am waiting on my SW102 and have read that you can power the motor by joining white to green. I gave the 8 pin plug from the motor the chop and joined the white and green but no...

Does anybody have the pinout showing colors for the plug on the SW102 to save me cutting my loom open ?

I have previously been using the marcoq version with the VLCD5 but just purchased the SW102 and cabling to attach to a new TSDZ2. I have found the links to wire and flash the SW102 but cannot for the life of me find instructions on how to use it once done. If someone could please give me links and ...

I have read "NOTE: the motor controller can be enabled by simple connect green wire to white wire and this way there is no need to use LCD." Is it possible to also adjust the power levels or use the throttle without the display ? I'm waiting on my SW102 and cabling but this might get me moving soone...

I have previously been using the marcoq version with the VLCD5 but just purchased the SW102 and cabling to attach to a new TSDZ2. I have found the links to wire and flash the SW102 but cannot for the life of me find instructions on how to use it once done. If someone could please give me links and a...

Not sure if this is the right place to ask but hopefully someone will point me in the right direction. I've gone to fit a TSDZ2 to an early Cannondale Scalpel and the RHS chainstay is in line with the outside of the bottom bracket. There is a ring on the rear of the case that protrudes about 1.5mm ...

Not sure if this is the right place to ask but hopefully someone will point me in the right direction. I've gone to fit a TSDZ2 to an early Cannondale Scalpel and the RHS chainstay is in line with the outside of the bottom bracket. There is a ring on the rear of the case that protrudes about 1.5mm a...

Possibly dangerous in the wrong situation. ....... Thoughts on what caused this ??? This is a known issue with older versions of Marcoq's software. Marcoq had solved this with the latest version. 3.7- M.0.19C Are you sure you have flashed this version ? Please read back and you find more about this...

Pretty sure l used the firmware from the github that stancoke had a link to page 14 l think. I'm away for a few days so will check when l return and update of required.

I'm using the V19 and 3.7. I tried to duplicate it this morning with no success. The only other thing I recall doing was toggling the light switch on and then off in turbo mode prior to this happening. It was not a bad situation for me but if the battery did not have a switch within easy reach I wou...

Possibly dangerous in the wrong situation. I was on my way home from work tonight it was dark and the road was wet - no traffic. My headlight has its own battery and I didn't have the backlight enabled on the VLCD5 as I find it to bright and it makes it difficult to see the road . As I passed under ...

Thanks. I set Street mode to 500w and Max speed of 45kph and l couldn't seem to tell the difference between E03 and E04 in level 1. Heat also seemed about the same getting to around 63°C on my 8km ride home from work using speed and turbo modes. I'm running a small stand alone temperature gauge with...

I have managed to flash the firmware and update and all is working well but I have a few questions regarding the modes. I have been using the below from ashrambo as a guide. VLCD5 and VLCD6 SCREENS functions : DEFAULT PARAMETERS -> E02 (Level 0) STREET MODE ENABLED -> E03 (Level 1) OFFROAD MODE ENAB...

I've been following this and reading for a while and not sure which way to go when l update. Is the KT LCD3 still viable as a display if not do l go for 850c or SW102 or stick with the VLCD5 with the marcoq version. I don't want to buy a display and find that it gets bricked when flashing it or hav...