Endless Sphere

????
Any more feedback?
Any new users?

Dan

Have you tried contacting them to see if they have any rear wheels left? They did have some.

Suicide, Has them post changed? It always talked like a suicide mission for a long time. 30mph on a 20" kids bike, that's too much for me. Oh, with shoe brakes too.

Dan

Remember, leaving batteries in the cold cuts capacity like half. Being used than the cold, they don't like that.

Dan

Chalo wrote: ↑

Dec 31 2020 4:41pm

And here I thought you were gonna tell us about your chainring.

Me too.

Dan

Your freezing and I have the AC on??? Only low 80s today, Gonna get cold soon, like 50s. Has been almost freezing last week! You don't wanna solder on the cells any more than really needed. It looks like your gonna solder direct to the cell not tabs, They really don't like the heat, especially the n...

Some cells are rated at 3.6v nominal and some at 3.7.

Those pictures are too fuzzy to see what is what.
And yes some of the plastic packs do need a hammer to crack the weld. have opened many laptop packs like that. Hit the corner of the pack, not too hard.

Dan

I liked the Barbie races. must of been a few too many beers before the races!

Dan

Call them and have them deliver it.

Dan

Separate the wires and take pics. Many hub kits are the same but then again many are not. So you find the power wires. Then the phase wires, and at many times will not color match. The hall wires also. You need to find the throttle wires and make sure red goes red and black to black. Then you might ...

dynamic operation, a small motor with high performance. Electric Motor for Go Kart, 48V, 2000W Forward & Reverse Rotation The motor can run forward or reverse simply by reversing its power wires Read it all. They have no idea what they are sellimg and don't care. I wish you would give up on the...

Are the frames Aluminum or steel? I doubt they would be Chromoly. I had to build a Chromoly rear suspension arm after the Aluminum cracked. Aluminum can only take so much pressure when tightening the axle nuts. The axle flats can split the dropout before you even get a ride out of it. Just trying to...

Maybe I shouldn't say this but, NOTHING you have will handle a Cromo hub motor at the power you are expecting. Yeah you can run a smaller controller so it doesn't destroy the bike but again why. There are many cheap DD hub motors that can do 40mph for a short distance and still be ridden at regular ...

I really don't know how they compare. You can get parts for Bafang but not sure where at this time. I believe that the used Bafang hubs are 500w since that is the most commonly used. 20mph should be no problem. I just think you are expecting too much for so little $. If you gotta have a Ferrari you ...

Look at the bottom of the item you are looking at and shipping is there. to your Zip looks like $24. Don't believe they do PO boxes. Remember these are all used, some more than others. Used cells and motors. Just look might not be what you want at all. Yes I have a Bafang 36v 350w? I believe. Ran fi...

Here you go. Cheap batteries and Bafang USED frt hub motors.
https://www.batteryclearinghouse.com/?u ... pify_email
Nevr dealt with so I don't know much about them.

Dan

LC, have you ever measured the tire diameter? Not what it says on the tire but measure the tire mounted to get the real dia. Or how about the circumference to get a real Speedo speed? All things do figure into gear ratios and actual speed. I will say, that your solder joints do look better, a lot. Y...

Hi, My name is Chris from France, I recently try to buy two batteries from EM3eV for my EB but I have a hard time to reach out to them by email. If someone have a more direct mean of reaching them, can you tell please? I have already send the money 💰 for this batteries by bank transfert but I don’t...

Too loud! Sounds like the chain is too tight, as I here a click click a lot. like the chain is hitting a spot or more on the sprockets, or a few master links. Sensorless controllers are pretty common now. Had/have one back in 07 still have it. It does work on a geared hub but not as well as a DD. I ...

I'm rather sure the charger I sent you has that option. You need to find the option in the manual or on line. I know my Ichargers and the 30a charger from HobbyKing has it. the internal resistor done on all those chargers are not really accurate but useful. Using a parallel board is the same as doin...

Don't put too much power into the Bikeling hub motors. I did and the clutch or one way bearing started slipping. I did like that little hub but it didn't like how I abused it. Was in a wet field of grass and weeds and when I hit the switch for more power it started slipping. I made it home but unabl...

Tis sad ... Everything indicates that you "need", have use for, would best appreciate an eBike with good range, geared for hills and use at only modest - safer speed ... but you continuously demand to dream and strive for, = "want", an eBike geared for ridiculously high speeds, ...

NFW would I consider a chain drive at that power on a flimsy bike frame. A motorbike conversion maybe but no way on a flimsy pedal bike frame. Just my personal feelings. Rear Hub motor but never a chain frt and rear. You want 50mph, all you need is a good rear hub 3kw motor and 72+ volts and you are...

That is cheap for a BMC kt. Especially from Hi-Power. A BMC is almost the same as a MAC. Mac copied and upgraded it. Mac offers a few more wind options. As for what's worth I have both. A BMC was my first Geared hub motor and I still have one on my wife's bike. I think it's about 8 yers of limited u...

have you tried turning the motor with the cover up and tapping on the axle with a piece of wood and hammer. The cover might just be rusted stuck on the axle. have done it before when the cover won't slide off. The rotor might move a little in the magnet ring but won't fall out unless you push it out...

before you get a gun, be sure you can get the ammo. Guns are plentiful but ammo is mostly cone. I think I only have about 1500 rounds right now. Used a lot at the gun range practicing

I hope you are wrong but am ready to protect my Wife and me as needed!

Dan