Search found 12 matches

by IronMan
Jan 08 2021 9:56am
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

-show error box is of no use (dont touch) -switch box changes between 3 (three) displays: 1.RPM, volts, current 2.RPM, Qvolt, Dvolt 3.RPM, Qcurrent, Dcurrent -Qvolt should be between 2000-3000 at hall right sync -Qcurrent should be optimal 200 at high RPM If Q values dont change while moving weak fl...
by IronMan
Jan 06 2021 11:38pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers (reverting)

Hey Everyone, I notice that my VOTOL 150 is being seen by the software as an EM100. I have set this to the 150 setting but every time I connect the software sees the 100 preset. I've tried saving the file, loading it but the it always returns to 100 setting, what gives, is there a remedy? Also once...
by IronMan
Jan 06 2021 2:07pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

OK. Please tell me what parameter should I control for stable operation of the motor at high rotation speed? You said earlier that the value should be in the range 100-200 ... what does the button mean " CLR DTC" ? in calibration section you should press the 'switch' box twice and you not...
by IronMan
Jan 06 2021 9:04am
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

Thank You. I will do it according to your recommendations. If my result is bad, I will wait for your detailed instructions. Question about port settings. What parameters absolutely cannot be set so as not to block the controller? I'm nervous ... :roll: ...added I have turned on the calibration menu...
by IronMan
Jan 05 2021 3:55pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

be careful with ports, or safe boot option or you can leave the controller blocked at parking mode or brake level high.. also calibraring throttle protection range
by IronMan
Jan 05 2021 3:46pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

I have an electric vehicle workshop and a lot of work, sorry that I havent been able to do the manual and the calibration tuto, change the keyboard to english US, open votol debug sw, put cursor at error count box and delet the 0, then hold shift, and press while shift pressed the button '~' twice, ...
by IronMan
Jan 05 2021 12:10pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

HI ! I cannot get the motor to run smoothly at high RPM. There is a knock and then a stop. It looks like a sync failure. I think so. Here is my controller settings. While testing without weakening the field. Who can help me? https://youtu.be/j35A8WuI-ME 1.jpg 2.jpg 3.jpg 4.jpg These values CANT be ...
by IronMan
Jan 05 2021 12:02pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

Before referring to ports (which is easy) I'll say your config is correct and its at top parameters, the jitter is at maximum and so the other values of calibration, you shouldnt touch them if the motor is spinning smoothly because they are meant only for phase sine wave timing (flux weakening RIGH...
by IronMan
Jan 04 2021 4:55pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

So, its my first post but Ive been reading ALL of this thread... first and most important I must say that new 4th generation Votol EM-50/100/150/200/250/300 has NEW firmware (.bin) that behaves differently, in older votol (still in stock) the values in flux and % slots were put the same and was abo...
by IronMan
Jan 04 2021 1:33pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

Hey guys, This is my first post on this forum ever. I want to use Votol with my homemade motor.The motor is made from a car generator. Installed magnets, Hall sensors with an external rotor. New winding. With a simple controller, the motor works fine. At 80 volts 5500 rpm, current 4.5 amps. But whe...
by IronMan
Jan 04 2021 1:31pm
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

they do explain the facts but only to manufacturers, and so they deliever good config and firmware files to them (TailG, AVA, BLS, Bryderk) in the end its them who buys the most.. so poor devils lile us dont really get too much attention..
by IronMan
Jan 04 2021 11:11am
Forum: E-Vehicles General Discussion
Topic: Votol EM-100 & EM-150 controllers
Replies: 1271
Views: 130429

Re: Votol EM-100 & EM-150 controllers

So, its my first post but Ive been reading ALL of this thread... first and most important I must say that new 4th generation Votol EM-50/100/150/200/250/300 has NEW firmware (.bin) that behaves differently, in older votol (still in stock) the values in flux and % slots were put the same and was abou...