Endless Sphere

..read the 12 pages now (was searching about the "real difference" about battery and current settings... iam going with lipos 18s15Ah 25C. so my question about current battery ---> my lipos can go easy 200Amps in this 18s3p setup. max motor phase current i found everywhere <- thats the set...

any news?

its turnigy not hobbyking.(manufacturer)
i bought this year round about 50 x 6s 5000mAh lipos. one of them was defect.( one cell dead) rest were all ok...
(you get what you pay. for ebikes good enough in every way)

charge the one cell to 3,68v

cycle (2x) with 5A the pack. (3,5v - 4,2v)
can you monitor the charging?

when this one cell drifts again send him back. you wouldnt get lucky in future.

Great Job Tekle.... :mrgreen: ...i have a new solution for my "speed"/PAS Problem.... i never tried cos i was still setting up my CA..... today i tried it..............THE CRUISE CONTROL :D now i can go on all Presets to every Speed i want. Just hold throttle 2 seconds on maybe 15kph and i...

I tried B22 also and my Settings to Max Thro Speed (6kph) wouldnt work. Please refer to the PAS section of the User Guide - it should clarify some points. But - the MaxThrotSpd setting only affects the "&" PAS modes, so you may have been tricked if you tried it when in an "|"...

with the start delay i have understand it in this way: default was 40 x 18ms i think. you have to get 40 signals before motor starts assist. with lower (for me works 25 fine) the assist comes early. what PAS dir you use? My arrows just blink in ony direction. did i pedal reverse the arrows goes in t...

for some in future having same problems...

i updated to beta 22 and now it works =)

today i will try setting up smooth PAS working.

O M G .....thank you so much

Hello amberwolf, the throttle works fine. I set it up to min 0,90v and max 3,51v smooth operating full range of throttle. i can see the slider in display for throttle and lyen did allready the "modification" with the resistor/diode. I made a little video: http://www.youtube.com/watch?v=eur...

On Screen 3 i dont see Pedaling RPMs......is that a hint for someone?!

cmon guys.....you US Boys are the one where germany looks

Yes i send him an email on monday morning....

yes i have.
tried everything.
today i have buyed another PAS (PAS v7)
Same...ich see the Arrows for Direction and 5v / 0v going up and down each Pas signal comes.

Motor do nothing

Hello, i have a Problem with Setup my CA v3 with Lyen 12fet Controller and PAS: 12 Pole Magnet Ring and Pedelec Sensor for V3 CA It is this PAS: http://www.ebikes.ca/store/photos/PAS_12P.jpg (Kingmeter) http://www.king-meter.com/products_sen.asp The PAS is from ebike.ca and has the Original Plugin f...

Hello Farfle,
i know and read about this modification with the green cable.
but what are the benefits on that modification?

as i wrote:

My question was: did i have to seperate the green cable from CA DP to Controllers Throttle IN to have more benefits?

no one can help?

hello, with modification i mean to seperate the green cable from CA DP to Throttle Input -> Controller. Thats what i DONT have done. I Just Plug my 3Pin Throttle INTO the CA v3. The CA v3 goes with the DP Connector to the Controller. (No other Cable goes through the Controller) I can see the little ...

Seems like a simple solution would be to create two testing parameters, with CA and without. Then measure your top speed between each. However, this test is hard to truly conduct outside, too many variables. Even if you ride on the same path in the same direction wind can play a pretty heavy part i...

Hello, can someone tell me how i can check out that my CA v3 really gives full throttle output? Iam not sure, because i think it is a difference between CA connected or not. i know the sound of the spinning wheel (without load) on full throttle... but with CA connected it is not the same...it is slo...

looks cool. i also want to load and balance all my 9 packs at the same time. did you leave the balance cable connected when using the accu? iam planing to leave balance cable connected to the parallel connected accus....they balance himself in use. but i have to use 2 (2x12s) or 3 (3x12s) balance co...

as u can see on revolectrix.com For Battery types: Lithium Polymer (1s to 8s balanced, 1s to 2s unbalanced), Lithium Ion (1s to 8s balanced, 1s to 2s unbalanced), Lithium Manganese (1s to 8s balanced, 1s to 2s unbalanced), A123 (LiFePO4) (1s to 8s balanced, 1s to 10s unbalanced), NiCd (1s to 21s), N...

Hope the 6kph can be edit to 99 also

really? before doc built this ultimate arms, what did you use before? i can follow when you have a 10KW Monster...but 2-3-4Kw?! i bet you will be right that before the mega torque arm will slip the axle will do. a normal DIN wrench 19mm is 8mm deep (a2) 250mm long (L) http://www.werkzeug-gedore.de/i...

hello,

when they are so strong why these Torque arms are 10mm deep?
i think 5mm will be enough...would look nicer i think?!
(like working tools for bolt / nut)

let me know if iam wrong.

regards from germany,

no answer here?