Endless Sphere

OK i need your input. Some of you guys know I make harnesses. A customer sent me his batteries and this battery case to make a harness. The battery configuration is 4s 3p or 88v 18AH using 6s 6 AH Turnigy Nanotechs. The first 4 slots on the left only hold 1 battery.The 4 slots on the right hold two ...

Capacity starts to suffer slightly but mainly voltage sag. With Hobby King batteries you must derate the batteries. Their stated rating which is labeled on the pack which is a peak rating is not to be used in a continuous fashion. The continuous rating of the cells is usually 1/4 of the stated ratin...

Hes going down hill in this video. You dont hear the motor at all until he turns behind the car. His other video you her the motor and hes traveling at a much believable speed.

So here is an update on the build. I went back to TDCM Torque Sensing Bottom Bracket after trying a lack luster 8 pole chinese pas sensor. You need a 120mm model to pull off the upgraded 60T chainring. I also upgraded to a 60T chain ring. This required a new crank set and chain ring from Vuelta USA....

Another one fresh out the oven. Went in a different direction and this one is a cast where I discuss my experiences with my 2012 Chevy Volt that I bought earlier this year. Available for download on my Onedrive. http://1drv.ms/1Ei74zF Episode # 14 https://www.youtube.com/watch?v=7M7lBwsxGKY I discus...

I cant tell the true listening amount. I am hosting it on my one drive so its probably driving some views away from youtube.

I got harassed to release this one. Ive been a little busy. Its on youtube and on my One drive. http://1drv.ms/1Ei74zF Episode # 13 https://www.youtube.com/watch?v=xtL12LoG6hU This cast is with guest caller Jay AKA Hyena on the ES Forums. We talk about the Flux Frame, Batteries, Motors, and Controll...

You are selecting the wrong crystalyte motor. The one you chose is obsolete.. not even in production anymore.

Noice!!

Just finished listening to the Kinaye podcast. I liked it a lot, made some notes about throttle ramp, batt/phase amps and block time was good to know too. Thanks. Here is a thought to ponder, try to get Justin Lemire-Elmore from http://www.ebikes.ca on one of your podcasts, maybe even John in CR or...

Will the 4T Mxus be updated in the simulator?

Another Cast fresh out the oven. Available on youtube and my One Drive. http://1drv.ms/1Ei74zF

Episode # 12 https://www.youtube.com/watch?v=Sy-KI4VGlv4
Guest Caller Barent Hoffman from Kinaye Motor Sports. http://www.kinayems.com We speak on the MXUS 3000w Motor and several of his projects.

Do yo think a thick stator fluid would have less leakage and running.. assuming at the cost of added drag. Or do you think that if the remaining amount is probably the perfect amount that would remain intact by magnetic forces without it slinging it every where. Any benefit with a vented setup.

Your charger should be able to discharge and charge the cell and give you MAH for both.

no. the only way to know the capacity is to measure it. to measure it you have to fully charge it and then fully discharge it. the voltage does not mean a thing. I believe you. I don’t want to start an argument here. Just for clarification. When I tried the following calculation: Taking the example...

Sounds like you dont want to actually check the batteries. Voltage isnt a good indicator at all on how much capacity is left in a cell or what the over all capacity. No you can not use your starting voltage and how much capacity you put in to the cell calculate the capacity. Capacity can only be cal...

Also can you grab any data on how long it takes for a sealed motor to cool and stabilize to the point where it makes no sense to wait because it will be like watching paint dry vs a vented in the same scenario. Basically I guess Time from Critical to Ambient. And would it to be better or faster to k...

The sealed motor is creating its own micro climate. I found the sealed motor took a while to shake the heat off and would essentialy stabilize but still drop over an extremely long period of time. While even slight disturbances such as a draft affects the drilled covers alot more so when the drilled...

I just finished a cast with teslanv. I will have it uploaded later today. Good Stuff.

Yes its my personal cloud drive. A link is in the first post in this thread.

Episode 11 is out on youtube and my One Drive. Episode #11 https://www.youtube.com/watch?v=beo6kh1u1OI This cast is an interview with Gary Salo at Golden Motor Canada. We go over his product line up, quality improvement over the years, customer service interactions, ebike safety and many other points.

Also something that I plan on doing to accomplish some things without asking the forum directly for support is non-skippable ads. I would like to use the money from this to buy products to review.Yay or Nay?

Episode 10 is out on youtube and my One Drive. Episode # 10 https://www.youtube.com/watch?=YaNqkoOfE4k Talked to Rafe Husain the owner of Calibike. We talked about his company, quality control of chinese vendors, his 40lbs 40 mph 40 miles bike, his plans for a 30lbs 30 mph 30 mile bike concept and d...

Go on my One drive and download the LQ cast. These are the ones I just recently compressed and they have 1 channel mono mixed audio. But again i said in the previous message that cast #10 onward shouldnt have this issue as you mentioned because I changed the setting in the recording software.

Ya but in the YouTube I only hear the guest. Is it same on downloads?? People keep asking you questions back to you but I don't ever hear your answers. The first few podcasts with a guest caller I had stereo recording enabled to where it simulated the caller on the left channel and me on the right ...