Help me ID this controller and what voltage I can use it with

Talk about anything and everything here within reason.
Post Reply
unclejemima
100 W
100 W
Posts: 207
Joined: Jun 10, 2012 3:59 pm
Location: Western Canada

Help me ID this controller and what voltage I can use it with

Post by unclejemima » Apr 15, 2018 1:07 am

I’ve got this controller from a few years back.

When I purchased it, it said “24-60v” in the listing...but when I got it, printed in it says only 48-60v

I’m using it with a 24v battery and it working but something keeps cutting out when I go wot.

I personally think it’s the BMS of the battery...a simple reset of the battery (turn key that is built in battery on and off) and it works again...provided I don’t go full throttle again. The battery is a super old lithium and must have a weak bms.

Is it possible for the Controller to cut power off?
Attachments
00CF9916-7E4A-400E-8353-C0A1F298F0D7.jpeg
00CF9916-7E4A-400E-8353-C0A1F298F0D7.jpeg (99.56 KiB) Viewed 91 times

DAND214
1 GW
1 GW
Posts: 3289
Joined: Aug 10, 2008 8:28 pm
Location: Chicagoland nw suburb Mt. Prospect IL. USA

Re: Help me ID this controller and what voltage I can use it with

Post by DAND214 » Apr 15, 2018 3:29 pm

Yes the controller could do it as it hits LVC. Normally the controller will come back as the voltage rises with no load. It sounds like the battery is done. A BMS shuts down to protect the battery from over load or a low/bad cell group. Since you need to turn off and on to regain power, it is most likely the battery,
If the controller said 24v/60v that is a wide voltage sprean and sounds like it doesn't have a LVC.
BATTERY.

Dan

User avatar
amberwolf
100 GW
100 GW
Posts: 25070
Joined: Aug 17, 2009 6:43 am
Location: Phoenix, AZ, USA, Earth, Sol, Local Bubble, Orion Arm, Milky Way, Local Group
Contact:

Re: Help me ID this controller and what voltage I can use it with

Post by amberwolf » Apr 15, 2018 6:02 pm

Couple good ways to test. First is to use a voltmeter on the battery output. If it drops below the normal level after the cutout, but resets to teh normal level after power cycling the battery, then the problem is the battery. If the voltage doesntchange, its the controller.

Or you can test teh cotnroller with a different battery, or the battery with a different controller.

User avatar
Dauntless
100 GW
100 GW
Posts: 6389
Joined: May 29, 2010 1:49 am
Location: Coordinates: 33°52′48″N 117°55′43″W

Re: Help me ID this controller and what voltage I can use it with

Post by Dauntless » Apr 15, 2018 11:47 pm

Did you notice there's a webpage listed on the lower left? I can't read it for the glare. There is company CHZD http://www.chzde.com/

I assume the whole thing resembles the Panlogic, even if the numbers don't match. Did yours come with a foot pedal? These people put more into explaining their PWM than the controller itself. Maybe you didn't get the controller you ordered, they do have 24v-60v. I'd say that one you can take at face value and wonder how it's even running at 24v. Brushed motor needing Hall throttle, not much I can offer.



Image
Any sufficiently advanced technology is INDISTINGUISHABLE FROM MAGIC!
- Arthur C. Clarke

unclejemima
100 W
100 W
Posts: 207
Joined: Jun 10, 2012 3:59 pm
Location: Western Canada

Re: Help me ID this controller and what voltage I can use it with

Post by unclejemima » Apr 16, 2018 9:44 pm

Thanks guys.

Good idea to test the voltage before and after cutout. I’m thinking battery as well.

So here’s the thing I’m confused about...what happens if I run an 18V battery with a controller that’s not designed for it? I tried an 18v battery and it worked like a champ...no cutting out

If the battery has a bms and it physically works...what’s the worst that can happen???

billvon
10 kW
10 kW
Posts: 930
Joined: Sep 16, 2007 9:53 pm
Location: san diego

Re: Help me ID this controller and what voltage I can use it with

Post by billvon » Apr 16, 2018 10:01 pm

unclejemima wrote:
Apr 16, 2018 9:44 pm
If the battery has a bms and it physically works...what’s the worst that can happen???
Overcurrent. Unexpected LVD or HVD. Controller burnout (if phase resistance/inductance is different than what the controller expects.)
--bill von

Post Reply