Adding CA Connector Infineon 18 FET Controller

Archive of useful information. This is not a discussion area.
Post Reply
User avatar
rkosiorek   1 MW

1 MW
Posts: 1770
Joined: Jan 18 2007 2:55pm
Location: Belleville, Ontario Canada

Adding CA Connector Infineon 18 FET Controller

Post by rkosiorek » Mar 22 2010 8:54pm

Lyen wrote:Hello Silver! Sorry to leave you in the dark for over 120 hours. I've been busy shipping things to many ES members here. But there is no excuse for me. I have made a thread here on how to wire it properly for you below so other members can benefit from it as well. Please let me know if you have any other questions. Thanks!
So here we go:

1. Determine the pin number & colors to the connector:
Image

2. Add a diode (1N4001) to pin number 6 (The negative of the diode goes towards the wire. Look at the picture carefully. Also, add a little PVC head shrink heat tube is ideal not not really needed):
Image

3. Solder a diode to the wire (Confirm the polarity):
Image

4. Add heat shrink tube:
Image

5. Short a resistor on R36:
Image
Image
Image

6. Solder in the blue wire with diode to the SLA pad:
Image
Image
Image

To be continue...
DISCLAIMER:
We will not be responsible for damage to equipment, your ego, blown parts, county wide power outages, spontaneously generated mini (or larger) black holes, planetary disruptions, or personal injury that may result from the use of this material.
- Samuel M. Goldwasser -
Top
User avatar
rkosiorek   1 MW

1 MW
Posts: 1770
Joined: Jan 18 2007 2:55pm
Location: Belleville, Ontario Canada

Re: Adding CA Connector Infineon 18 FET Controller

Post by rkosiorek » Mar 22 2010 8:55pm

Lyen wrote:7. Solder pin #1 to VK2+ and pin #4 to the shunt location below:
Image

8. Pin #2 to GND-8 (next to XC -)
9. Pin #3 to GND-8 (between pad P3 & XC)
10. Pin#5 to HE below:
Image

Let me know if you have more questions. Thanks! :)
DISCLAIMER:
We will not be responsible for damage to equipment, your ego, blown parts, county wide power outages, spontaneously generated mini (or larger) black holes, planetary disruptions, or personal injury that may result from the use of this material.
- Samuel M. Goldwasser -
Top
User avatar
rkosiorek   1 MW

1 MW
Posts: 1770
Joined: Jan 18 2007 2:55pm
Location: Belleville, Ontario Canada

Re: Adding CA Connector Infineon 18 FET Controller

Post by rkosiorek » Mar 22 2010 8:56pm

SilverSurfer wrote:Bro, I think your note number 9 should read pin #3. Or you need to list pin 3's location if its not gnd 8.
Lyen wrote:7. Solder pin #1 to VK2+ and pin #4 to the shunt location below:
Image

8. Pin #2 to GND-8 (next to XC -)
9. Pin #2 to GND-8 (between pad P3 & XC)
10. Pin#5 to HE below:
Image

Let me know if you have more questions. Thanks! :)
DISCLAIMER:
We will not be responsible for damage to equipment, your ego, blown parts, county wide power outages, spontaneously generated mini (or larger) black holes, planetary disruptions, or personal injury that may result from the use of this material.
- Samuel M. Goldwasser -
Top
User avatar
rkosiorek   1 MW

1 MW
Posts: 1770
Joined: Jan 18 2007 2:55pm
Location: Belleville, Ontario Canada

Re: Adding CA Connector Infineon 18 FET Controller

Post by rkosiorek » Mar 22 2010 8:57pm

Lyen wrote:Oops! Sorry! I have updated with the correct info. :)
DISCLAIMER:
We will not be responsible for damage to equipment, your ego, blown parts, county wide power outages, spontaneously generated mini (or larger) black holes, planetary disruptions, or personal injury that may result from the use of this material.
- Samuel M. Goldwasser -
Top
User avatar
rkosiorek   1 MW

1 MW
Posts: 1770
Joined: Jan 18 2007 2:55pm
Location: Belleville, Ontario Canada

Re: Adding CA Connector Infineon 18 FET Controller

Post by rkosiorek » Mar 22 2010 8:58pm

Mike1 wrote:Pin 2 should really be connected close the the bottom of the shunt. I connect pin 3 there also.
DISCLAIMER:
We will not be responsible for damage to equipment, your ego, blown parts, county wide power outages, spontaneously generated mini (or larger) black holes, planetary disruptions, or personal injury that may result from the use of this material.
- Samuel M. Goldwasser -
Top
User avatar
rkosiorek   1 MW

1 MW
Posts: 1770
Joined: Jan 18 2007 2:55pm
Location: Belleville, Ontario Canada

Re: Adding CA Connector Infineon 18 FET Controller

Post by rkosiorek » Mar 22 2010 8:59pm

Lyen wrote:
Mike1 wrote:Pin 2 should really be connected close the the bottom of the shunt. I connect pin 3 there also.
I believe you are correct as well Mike! I however do not see the differences in terms of accuracy. So this is just a personal preference for now until someone has hard evidence. Thanks! :)
DISCLAIMER:
We will not be responsible for damage to equipment, your ego, blown parts, county wide power outages, spontaneously generated mini (or larger) black holes, planetary disruptions, or personal injury that may result from the use of this material.
- Samuel M. Goldwasser -
Top
User avatar
rkosiorek   1 MW

1 MW
Posts: 1770
Joined: Jan 18 2007 2:55pm
Location: Belleville, Ontario Canada

Re: Adding CA Connector Infineon 18 FET Controller

Post by rkosiorek » Mar 22 2010 9:03pm

these instructions were originally posted as Adding CA Connector for SilverSurfer's 18 FET Controller

http://www.endless-sphere.com/forums/vi ... =2&t=17022

thanks Lyen for the excellent directions

rick
DISCLAIMER:
We will not be responsible for damage to equipment, your ego, blown parts, county wide power outages, spontaneously generated mini (or larger) black holes, planetary disruptions, or personal injury that may result from the use of this material.
- Samuel M. Goldwasser -
Top
Post Reply

Return to “Technical Reference Area”