2WD Semi-Recumbent Recycled-Parts Cargo eBike: "CrazyBike2"

Get all your technical information about electric bikes here.

Re: Semi-Recumbent Recycled-Parts Cargo eBike: "CrazyBike2"

Postby amberwolf » Fri Jan 06, 2017 4:37 pm

Been using the EIG 14s1p pack from this on SB Cruiser since getting it operational again, as the A123 pack is insufficient to run SBC due to some odd behavior in the righthand motor controller of SBC cutting out at too high a voltage (which it didnt' used to).

But anyway, today I did some testing with a freshly-built (out of old cells but used a lot less than the original pack) 14s2p EIG NMC pack, vs the original 14s1p, just a couple of quick runs from 0-20MPH on each one.

Test done with each pack in turn, packed into the toolbox rather than working into the frame like normal (is a PITA). Each started out at 58v. Note that the 14s2p weighs twice the 1p, so the 2p's runs have that added maybe 20-ish pounds. (less than 10% of bike weight, probably around 6-7% total with me on there)
img_4066.jpg
img_4066.jpg (117.42 KiB) Viewed 495 times



The 14s2p EIG did better than the 14s1p, but is fairly close for this kind of short run at full charge. Probably see much more difference over a work commute, for instance. Took about 3-3.5 seconds 0-20MPH; distance in the street from the corner of my front yard to the side gate start. Run back was the same. Less sag than the other.
57.7 vrest
54.2Vmin
0.141Ah
8.2480wh
79.54Amax
0.071mi

The 14s1P EIG took about 4-4.5 seconds, going all the way past the side gate. Run back about the the same, maybe a hair more time and distance.
56.9 vrest
48.9Vmin
0.148Ah
8.1310wh
79.01Amax
0.081mi
User avatar
amberwolf
100 GW
100 GW
 
Posts: 23487
Joined: Mon Aug 17, 2009 6:43 am
Location: Phoenix, AZ, USA, Earth, Sol, Local Bubble, Orion Arm, Milky Way, Local Group

Re: Semi-Recumbent Recycled-Parts Cargo eBike: "CrazyBike2"

Postby amberwolf » Tue Jan 17, 2017 5:13 am

For a while, CB2 is going to just be FWD, with the rear wheel/motor/controller, and just have a regular bike wheel in back, becuase I needed to move ti's motor/wheel over to SB Cruiser's left wheel, due to a problem with the 9C's axle on the hollow (inboard, wire) side.

See the SB Cruiser thread, past couple days' of posts, for more details on that.
User avatar
amberwolf
100 GW
100 GW
 
Posts: 23487
Joined: Mon Aug 17, 2009 6:43 am
Location: Phoenix, AZ, USA, Earth, Sol, Local Bubble, Orion Arm, Milky Way, Local Group

Re: 2WD Semi-Recumbent Recycled-Parts Cargo eBike: "CrazyBi

Postby amberwolf » Sat Sep 02, 2017 4:13 am

So CB2 has been down essentially since the above. Well, it was functional minus the rear motor for a bit, but then I took the front forks off of it to swap with SB Cruiser and haven't gotten round to putting the SBC fork onto CB2. I keep intending to go back and fix it up so it can be my backup in case SBC is down, but whenever there's time either the weather hasnt' allowed it or else I wasnt' phsyically able to do it, and whenever I could've done it there's been no time. :/

However, I really came back to the thread to post this, that I found while I was looking at streetviews for something else (stupid traffic stuff in my area), for a post here:
viewtopic.php?f=2&t=67833&p=1316753#p1316753

I found a perfect side view of CB2 in traffic, probably on my way to work, here:
https://www.google.com/maps/@33.5815784 ... 312!8i6656
dated September 2016, one year ago this month. :)

Click image thumbnails for full size image
Attachments
crazybike2 sept2016 streetview 1.jpg
crazybike2 sept2016 streetview 2.jpg
crazybike2 sept2016 streetview3.jpg
User avatar
amberwolf
100 GW
100 GW
 
Posts: 23487
Joined: Mon Aug 17, 2009 6:43 am
Location: Phoenix, AZ, USA, Earth, Sol, Local Bubble, Orion Arm, Milky Way, Local Group

Previous

Return to E-Bike Technical

Who is online

Users browsing this forum: Google [Bot], Yahoo [Bot] and 16 guests