Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Get all your technical information about electric bikes here.
User avatar
PITMIX   100 W

100 W
Posts: 261
Joined: Nov 18 2018 3:25pm
Location: France

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by PITMIX » Sep 01 2020 8:33am

Hi friends, i did the latest firmware update. The acceleration curve is very different although I kept the same settings. I really like how it works now, but I would like to know how to modify it? The starts are smoother and linear then the power delivers as if there was a Turbo. With the old firmware was abrupt at startup and then linear in acceleration.
Aixam 550 Twin retrophite Qs 138 70H, Thermo-Nucular electronics 24F, LG Chem 20s 60Ah

User avatar
PITMIX   100 W

100 W
Posts: 261
Joined: Nov 18 2018 3:25pm
Location: France

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by PITMIX » Sep 03 2020 3:30am

Its good ! :wink: I found it is in " control mode" there is a Throttle / brake curves adjustment and a lot of parameters to adjust it's great. :bigthumb: :D
Aixam 550 Twin retrophite Qs 138 70H, Thermo-Nucular electronics 24F, LG Chem 20s 60Ah

electraflyit   10 W

10 W
Posts: 82
Joined: Jul 08 2008 12:19am
Location: Toowoomba, Queensland

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by electraflyit » Sep 10 2020 1:09am

endrew wrote:
Jul 20 2020 7:33am
OK, I was wrong. When setting control mode to FOC, the motor stutters, see attached video:

https://youtu.be/I71vRFXVekE
Hi,
Did you find what the problem was when the motor stutters.
I have the same problem. Motor starts smoothly then stutters at about half speed.
MXUS 3k
Eddie

User avatar
PITMIX   100 W

100 W
Posts: 261
Joined: Nov 18 2018 3:25pm
Location: France

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by PITMIX » Sep 10 2020 1:16am

it is necessary to reduce the setting of KPi to 100 instead of 500
Aixam 550 Twin retrophite Qs 138 70H, Thermo-Nucular electronics 24F, LG Chem 20s 60Ah

endrew   10 W

10 W
Posts: 76
Joined: Apr 07 2018 12:05pm

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by endrew » Sep 10 2020 3:02pm

electraflyit wrote:
Sep 10 2020 1:09am
endrew wrote:
Jul 20 2020 7:33am
OK, I was wrong. When setting control mode to FOC, the motor stutters, see attached video:

https://youtu.be/I71vRFXVekE
Hi,
Did you find what the problem was when the motor stutters.
I have the same problem. Motor starts smoothly then stutters at about half speed.
MXUS 3k
Eddie
It was the motor, Do not support FOC, probably hall sensors. Different motor works fine.

electraflyit   10 W

10 W
Posts: 82
Joined: Jul 08 2008 12:19am
Location: Toowoomba, Queensland

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by electraflyit » Sep 11 2020 4:55pm

Vasily in the telegram forum advised on a PID value change that fixed my stuttering problem.

User avatar
PITMIX   100 W

100 W
Posts: 261
Joined: Nov 18 2018 3:25pm
Location: France

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by PITMIX » Sep 12 2020 1:52am

yes which confirms what I say 2 messages above. No need to change the engine the Nucular adapts.
Aixam 550 Twin retrophite Qs 138 70H, Thermo-Nucular electronics 24F, LG Chem 20s 60Ah

transposon   100 W

100 W
Posts: 116
Joined: Nov 24 2011 4:37pm
Location: Massachusetts

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by transposon » Sep 15 2020 11:57am

I am about to place an order for a 6F controller. I had a few questions on what accessories I needed.

Is the "PWM IO/PAS wire" option only used for PAS? Or can it be used for other things?

Also, if I wanted to add front, rear, or turn signal lighting down the road, what options would I need? I assumed "Optical-isolated PWM driver". Would I ever need more than one of these addons?

Thanks.

User avatar
VasiliSk   1 kW

1 kW
Posts: 361
Joined: Apr 10 2014 5:11am
Location: Russia

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by VasiliSk » Sep 15 2020 12:39pm

This cable for FAN / stoplight / PAS

What you described - you need uLight board.

transposon   100 W

100 W
Posts: 116
Joined: Nov 24 2011 4:37pm
Location: Massachusetts

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by transposon » Sep 15 2020 12:57pm

VasiliSk wrote:
Sep 15 2020 12:39pm
This cable for FAN / stoplight / PAS

What you described - you need uLight board.
Thanks for the reply. Do I need to get any options to make sure that uLight will work with my controller?


transposon   100 W

100 W
Posts: 116
Joined: Nov 24 2011 4:37pm
Location: Massachusetts

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by transposon » Sep 16 2020 4:44pm

Is the "PWM IO/PAS wire" removable or is it soldered directly to the controller?

Also, is the CAN cable accessory just an extra replacement cable or is it soldered to the controller?

User avatar
PITMIX   100 W

100 W
Posts: 261
Joined: Nov 18 2018 3:25pm
Location: France

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by PITMIX » Sep 16 2020 11:52pm

all cables are connected to jst-x on the motherboard.
Look at this :
https://drive.google.com/file/d/1KkEgWc ... sjpUQ/view
Aixam 550 Twin retrophite Qs 138 70H, Thermo-Nucular electronics 24F, LG Chem 20s 60Ah

transposon   100 W

100 W
Posts: 116
Joined: Nov 24 2011 4:37pm
Location: Massachusetts

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by transposon » Sep 20 2020 9:02pm

Did you guys have to split up the payment into 2 separate payments? One via paypal and one via cloud payment? Just wanted to make sure that this was legit.

Thanks.

User avatar
Merlin   10 MW

10 MW
Posts: 2084
Joined: Jan 29 2013 10:00am
Location: europe

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by Merlin » Sep 20 2020 9:08pm

Doesn't sound right 🤔

Buyed above 20 controllers... All with sepa payment.

iacei   100 mW

100 mW
Posts: 49
Joined: Dec 18 2016 8:15am

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by iacei » Sep 21 2020 6:22am

Hi Folks,

I currently have my ebike configured with a reention dp6 battery.

To power my bike I have to switch the battery one and then the Nuc.

Is there a way to configure the Nuc so that it powers on as soon as I start my battery?

j bjork   10 kW

10 kW
Posts: 741
Joined: Aug 31 2018 3:01pm
Location: Linköping, Sweden

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by j bjork » Sep 21 2020 7:40am

Yes, I think you just set button "none" somewhere in the config.
I dont remember where, but it is probably in the manual.
I think I was able to find it just looking in the menus.

Tommm   100 kW

100 kW
Posts: 1105
Joined: Apr 03 2018 2:32am

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by Tommm » Sep 21 2020 7:56am

Do we have an idea where they are with the backlog?

gbeals   1 W

1 W
Posts: 55
Joined: Apr 15 2020 11:43pm
Location: Honolulu, Hawaii
Contact:

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by gbeals » Oct 06 2020 9:36pm

If you folks could not get the Nucular Controller, what would have gone with? I've had the Votol and did not come with progressive regen and software was buggy with so many different versions to choose from as well.

I'm on the wait list for Nucular, but need to get something to pair up to my QS3kw motor. My Votol was 150 model and was plenty for that motor. Anything else on the market that is comparable?

User avatar
PITMIX   100 W

100 W
Posts: 261
Joined: Nov 18 2018 3:25pm
Location: France

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by PITMIX » Oct 07 2020 12:17am

Kelly ... Sabvoton ... but the only one that compares to the Nucular is the Adaptto
Aixam 550 Twin retrophite Qs 138 70H, Thermo-Nucular electronics 24F, LG Chem 20s 60Ah

andrewrich   1 mW

1 mW
Posts: 12
Joined: Sep 14 2020 6:34pm

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by andrewrich » Oct 08 2020 4:55pm

Hello all I was just wondering if I could get a little help. I just purchased a Nucular 6f and got it all set up today. I am using a cyclone 3000w motor and 72v battery. the problem is when I start to pull away the motor stutters, it only happens on very low throttle. is there some setting somewhere that will help me get rid of the stutter ? or has anyone got a cyclone 3000w already set up that I can have the config for ?. Any Help is greatly appreciated. Thanks.

John in CR   100 GW

100 GW
Posts: 14765
Joined: May 20 2008 12:58am
Location: Paradise

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by John in CR » Oct 08 2020 5:05pm

andrewrich wrote:
Oct 08 2020 4:55pm
Hello all I was just wondering if I could get a little help. I just purchased a Nucular 6f and got it all set up today. I am using a cyclone 3000w motor and 72v battery. the problem is when I start to pull away the motor stutters, it only happens on very low throttle. is there some setting somewhere that will help me get rid of the stutter ? or has anyone got a cyclone 3000w already set up that I can have the config for ?. Any Help is greatly appreciated. Thanks.
It sounds like it may still be set to sensorless control. Set it to FOC and save.

andrewrich   1 mW

1 mW
Posts: 12
Joined: Sep 14 2020 6:34pm

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by andrewrich » Oct 08 2020 5:08pm

John in CR wrote:
Oct 08 2020 5:05pm
andrewrich wrote:
Oct 08 2020 4:55pm
Hello all I was just wondering if I could get a little help. I just purchased a Nucular 6f and got it all set up today. I am using a cyclone 3000w motor and 72v battery. the problem is when I start to pull away the motor stutters, it only happens on very low throttle. is there some setting somewhere that will help me get rid of the stutter ? or has anyone got a cyclone 3000w already set up that I can have the config for ?. Any Help is greatly appreciated. Thanks.
It sounds like it may still be set to sensorless control. Set it to FOC and save.
its already in FOC Mode. any other ideas?

john61ct   100 GW

100 GW
Posts: 6668
Joined: Dec 18 2018 2:06pm

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by john61ct » Oct 08 2020 11:32pm


gbeals wrote: something to pair up to my QS3kw motor
QS sells Kelly 7230S for up to 3kW I think

Anybody know if it does FOC?


User avatar
PITMIX   100 W

100 W
Posts: 261
Joined: Nov 18 2018 3:25pm
Location: France

Re: Nucular Electronics owner's thread (setup infos, FW updates, links etc.)

Post by PITMIX » Oct 08 2020 11:51pm

@John61ct, Yes he's doing FOC.
@Andrewrich On PID regulator, You can decrease the KPi setting to 100.
Did you set the number of poles correctly ?
Did you do the last update?
Aixam 550 Twin retrophite Qs 138 70H, Thermo-Nucular electronics 24F, LG Chem 20s 60Ah

Post Reply