The BEST and FIRST Qulbix Raptor mid-drive build!

Discussions related to motors other than hub motors.
This includes R/C motors, botttom bracket, roller and geared drives.
tikivic
1 W
1 W
Posts: 51
Joined: Mar 23, 2016 2:32 pm
Location: Santa Clarita Valley, CA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by tikivic » Jul 17, 2017 10:03 pm

Elegant solution Mike. Mine is decidedly less elegant, I moved the axle all the way forward, and machined a spacer that goes behind the axle secured by the pinch bolt. So of course I have no adjustment for the chain tension, that is handled via the Rohloff chain tensioner. I am curious if (why) you require the adjustment (i.e. motorcycle) and if so how you get around the chain growth on the Raptor as the suspension moves?

V.
IMG_0940.jpg
IMG_0940.jpg (55.92 KiB) Viewed 1174 times



LightningRods wrote:My chain tugs arrived. They are almost perfect as delivered. I had to relieve the front of the raised boss that rides in the dropout slot, and I had to widen the slot on the adjuster nut bracket to accommodate the unusually wide Qulbix dropout:

Image

I was able to make those mods with an angle grinder and a flat file. With those two changes the tug fits like a factory part:

Image

This should positively keep the axle from sliding forward under power.

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Jul 17, 2017 10:17 pm

Thank you V. I was stressing over this a bit and was relieved to have it resolve so nicely.

The chain required tensioning because the center to center distance with the axle all the way forward just missed being short enough for one link pair less. Once I added a link pair the chain was floppy loose. I needed to move the axle back about .316" and somehow have it not slip under power. The chain tugs were the solution.

There is zero chain growth because the motor is mounted on the swingarm. I was originally going to mount the motor on the main part of the frame but was persuaded that the lack of chain shenanigans made the unsprung weight (near the fulcrum point) a reasonable trade off.

I was just online looking at Rohloff tensioners for the pedal side. I wasn't lucky enough to get both chains properly tensioned at the same axle position.
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

tikivic
1 W
1 W
Posts: 51
Joined: Mar 23, 2016 2:32 pm
Location: Santa Clarita Valley, CA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by tikivic » Jul 18, 2017 10:21 am

That makes sense now, I forgot you are doing the swingarm mount. I have a little over 800 miles now on the Rohloff tensioner (Cyclone 3000W) and no issues at all. I did have to machine down the inside of the derailleur cage to accept a wider chain though.

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Aug 01, 2017 2:17 pm

I'm settling into production on the 165mm billet hubs for the swingarm drive. My machinist has made some fixtures to speed production, all the little issues have been sorted, and I was pleased to find that my local plating shop is under new management. I got my black anodizing back in a week at a good price and the parts look great.

Image

I've been running my own swingarm drive around for a couple of weeks and I'm very impressed with it. It's the quietest drive I've ever made since there are very few moving parts. With 84v 8O amps it runs great with one speed. The only change I have planned is a two speed geared chainwheel from PowerVelocity. The 1.7:1 overdrive will make it possible to pedal with the motor up to 4O mph or so.
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
skeetab5780
1 MW
1 MW
Posts: 1940
Joined: Jun 15, 2009 10:58 pm
Location: MA
Contact:

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by skeetab5780 » Aug 02, 2017 11:03 am

You still sell the 6kw hd motor? How much are they going for out of curiosity I love mine!

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Aug 02, 2017 11:23 am

The motor you're running is completely different from mine. A lot of people are using "LR motor" or "big block" to describe any large motor they've found. That's E-S. Everything gets appropriated.
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
skeetab5780
1 MW
1 MW
Posts: 1940
Joined: Jun 15, 2009 10:58 pm
Location: MA
Contact:

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by skeetab5780 » Aug 02, 2017 11:42 am

Well do you sell more of the motor you sold me? not sure what the proper name is

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Aug 02, 2017 11:55 am

Apologies. Your profile photo still shows the original BHT motor on the swingarm drive. I went through your thread and saw that you swapped that motor out for one of mine later in the build. LMX did the same thing. They started with the BHT and then switched to my motor and are still using it.

The Big Block is still $325 USD.
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Aug 03, 2017 3:24 pm

Jake P. has his Q140R up and running. Apparently he has already caused a pizza delivery boy to soil himself by coming up on him silently at 30 mph. The poor kid thought that some apex predator was about to grab him off of his bicycle.

Jake's bike gets to be in the office during the day because it's well behaved and doesn't leak oil on the carpet.

Image

Jake has also employed the wheel tugs. After a bit of filing they work well. Jake has no right side sprocket because he is rocking footpegs. You are not going to find a simpler mid drive setup than this

Image
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
Luk
100 mW
100 mW
Posts: 41
Joined: Feb 16, 2014 1:01 am

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by Luk » Aug 03, 2017 5:04 pm

An overdrive from PowerVelocity ?!
Luk-ebike.fr

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Aug 03, 2017 5:22 pm

Jake doesn't have pedals and so can't benefit from the o.d. crankset. Ive told Vad at PowerVelovity that I want one. It's going right onto my Q76. Two speeds in front and one in back will be perfect!
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Aug 03, 2017 5:25 pm

Luk your swing arm drive is ready to ship. I need to work out the details with you.

I have two drives and hubs left. More are being made.
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

devo1223
10 W
10 W
Posts: 78
Joined: Nov 06, 2012 4:32 pm
Location: Lake Tahoe,CA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by devo1223 » Aug 03, 2017 5:57 pm

I think the direct drive is my next build. Mike, what is your top speed at 84v? how's the motor temp in the tight/rocky stuff? Can you give us an idea of the power compared to the hubbie that was on there?
Vector lite
Mxus 3k turbo 3t in 17in moto rim

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Aug 03, 2017 6:17 pm

I did the math and the drive is geared for 55 mph @ 84v. 650 wheel rpm.

The bike has noticeably better acceleration now, especially from a stop. The 3000 watt hub maintained speed well up hills but was soggy and slow off of the line. I have a much better controller now than I had with the hub so it's hard to say how much that enters into it. I'm still only seeing 3100 max on the CA. I think the battery that came with the bike may be limiting the 6kw+ the Big Block and PowerVelocity 18 FET are capable of. So I may have the potential for twice the present power! Time to contact EM3EV. :mrgreen:

The ride is noticeably smoother off road. The suspension is quicker to respond now and soaks up the high frequency stuff that came through with the hub.
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
madin88
10 MW
10 MW
Posts: 2496
Joined: May 27, 2013 2:02 am
Location: Austria

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by madin88 » Aug 04, 2017 10:06 am

LightningRods wrote: The ride is noticeably smoother off road. The suspension is quicker to respond now and soaks up the high frequency stuff that came through with the hub.
This is so true!
- Votec V-FR frame / MXUS 3T / 17" Mitas MC11 / Adaptto Max-E / 20s12p 25R -> approved as L1e moped and fully road legal in EU :)
- Vector white / MXUS 4T / 24" Hookworms / Adaptto Max-E / 22s11p 25R
- KTM Hardtail Pedelec / eZee V2 6T / 27,5" / Kelly KBSX @ 1,5kW / Torque PAS / CA-V3 / 13s4p Sanyo GA in Shark case

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Nov 26, 2017 8:22 pm

The Enduro Electric Bike version of the swingarm drive is now available. It's very similar to the Qulbix drive except that the brackets are revised to fit the Enduro swingarm and there are added horizontal dropout extensions so that the drive chain can be tensioned.

Image

Image

Image

Image

Image

Image

Image

Image
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
Bbeforeart
1 mW
1 mW
Posts: 15
Joined: Feb 25, 2017 6:38 am

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by Bbeforeart » Jan 29, 2018 3:07 am

Hi there

I really like this fixed spocket type of setup, without pedals to keep it clean! I am wondering what this motor setup would cost including chainwheels and chain (tensioner)?

Regards, Bart

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Jan 29, 2018 11:09 am

Hi Bart,

The pedals really expand the usefulness of the bike but I know that Qulbix does offer a foot peg package. It’s an off road toy only with foot pegs.

Customer totals are coming up right around $1k for the drive, rear hub, sprockets, chain, brake mount and chain tugs. The EEB version needs dropout extensions for $50. That’s the only cost difference.

Thanks,
Mike
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
Bbeforeart
1 mW
1 mW
Posts: 15
Joined: Feb 25, 2017 6:38 am

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by Bbeforeart » Feb 08, 2018 5:28 pm

Dear Mike,

Thanks for your reply. That sounds very interesting to me!

I really see this as an advantage opposed to my Crystalyte HS3540 with a 72v25Ah battery setup providing 3000w peak. It does not provide sufficient torque at lower speeds, that's why this took my attention.

Furthermore, I am wondering if it is feasible to have a Qulbix Q76R with that mid drive kit without a chain tensioner?

Lastly, how much will the shipping be to the Netherlands?

Regards,

Bart

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Feb 08, 2018 6:20 pm

Hi Bart,

I ran my Q76 with a 3000 watt hub motor and then with my swingarm drive at the same power level (battery limited). The swingarm drive has much better low end due to the 8:1 reduction. The hub motor was actually better overall than I thought it would be except that it was super soggy at take off.

I’m not sure that I’m completely following your question about the mid drive. Are you referring to the chainwheel drive where the motor is mounted on the front of the bike? Yes it works great on the Q76. The Q130’s battery box is a bit wide for the front mount motor. What do you mean by “without chain tensioner”? The secondary chain drive from the jackshaft to the chainwheel does need a roller tensioner.

If you want to go single speed with a chainwheel drive you could also mount my single stage drive on a Q76 just like I did on the FUTR Beta. You can get much lower gearing with that system than the 8:1 of the swingarm drive.

Shipping to the Netherlands should be in the range of $120 USD.

Thanks,
Mike
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

User avatar
efMX Trials Electric Freeride
10 kW
10 kW
Posts: 931
Joined: Feb 15, 2013 4:43 pm

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by efMX Trials Electric Freeride » Feb 08, 2018 6:54 pm

if you mount a mid drive motor to the bike main frame then you will need a chain tensioner at the rear dropout to allow for rear suspension movement.. but if you mount a mid drive motor on the swingarm then you will not need a chain tensioner because the motor drive will be moving with the swingarm and will not effect chain tension..
Bbeforeart wrote:
Feb 08, 2018 5:28 pm
Dear Mike,

Thanks for your reply. That sounds very interesting to me!

I really see this as an advantage opposed to my Crystalyte HS3540 with a 72v25Ah battery setup providing 3000w peak. It does not provide sufficient torque at lower speeds, that's why this took my attention.

Furthermore, I am wondering if it is feasible to have a Qulbix Q76R with that mid drive kit without a chain tensioner?

Lastly, how much will the shipping be to the Netherlands?

Regards,

Bart
some ride & sk8 videos:
metacafe.com/channels/NATAS666DAMIEN
http://www.youtube.com/natas666damien
i have nothing for sale.. :)

User avatar
LightningRods
10 MW
10 MW
Posts: 2066
Joined: Oct 23, 2012 7:37 pm
Location: Western Oregon, USA

Re: The BEST and FIRST Qulbix Raptor mid-drive build!

Post by LightningRods » Feb 08, 2018 7:02 pm

You don’t need a spring loaded tensioner. You do need some way to get the chain properly tensioned to start with. You are correct that chain tension doesn’t vary with suspension movement on a swingarm drive.
"I don’t mind that they stole my idea, I mind that they don’t have any of their own.”
-Nikola Tesla

Lightning Rods Web Site http://www.lightningrodev.com
Lightning Rods Facebook Page https://www.facebook.com/pages/Lightnin ... 4531978401

Post Reply