johnnyfoos
100 mW
Hello,
I have a question about speed controllers-
Regarding The Voltage
How Under or Over these can handle and still work with letting out the smoke??
What I have on hand-
(YK31C 500W 24V and 36V){one of each}
(LK-03 350W 24V)
Brushed motor controllers
The "WHY"-
My reason-
The batteries on hand-
When the local Radio Shack was closing down last year
I stocked up on these,(very cheap)
"DigitalEnergy" Packs, {20+ packs}
NI-MH, 9.6V, 1600mAH, 8 cell packs
When fresh off the charger 10.6V
I don't want to reweld/rebuild these packs, (no spot welder)
my 4 different chargers can NOT even charge these in 2S, (only 15 cells max)
So I'll have to rack them up in a box that lets me 3S or 4S, X 3 or 4 P
(30 volts into the 24V controller? or the 36V one?)
(40 volts into the 36V one?)
The Ride-
A rebuilt Razor Electric Punk,
( with the folding collapsing still working to hopefully still fit into a suitcase)
stretched front end, suspentioned, racked back with a 12.5x2.25 three spoked wheel
Lengthened and widened rear wheel mount with a FREE Wheeled 10x35-4 with two extra spring shocks
replaced the 12V, 80W motor, still using stock mounting system, Tensionable drive belt
Waiting for a battery system-
installed for scare testing-
MY1016, 18V, 2700RPM, 150W, 10.9A
If 150W wasn't to BAD,
ON hand- ( using same mounting hole pattern)
MY1016, 24V, 2750RPM, 300W, 16.4A unite motor
MY1018, 24V, 2500RPM, 300W, 16.5A JX motor
So-
PLEASE let me know what you think about the battery and controller problem I have
NO! I don't want to BUY Li- anything right now
I've got all those NiMh's and a big box of Ni-Cads, ALL NEW needing to get used!
Just
Asking
I have a question about speed controllers-
Regarding The Voltage
How Under or Over these can handle and still work with letting out the smoke??
What I have on hand-
(YK31C 500W 24V and 36V){one of each}
(LK-03 350W 24V)
Brushed motor controllers
The "WHY"-
My reason-
The batteries on hand-
When the local Radio Shack was closing down last year
I stocked up on these,(very cheap)
"DigitalEnergy" Packs, {20+ packs}
NI-MH, 9.6V, 1600mAH, 8 cell packs
When fresh off the charger 10.6V
I don't want to reweld/rebuild these packs, (no spot welder)
my 4 different chargers can NOT even charge these in 2S, (only 15 cells max)
So I'll have to rack them up in a box that lets me 3S or 4S, X 3 or 4 P
(30 volts into the 24V controller? or the 36V one?)
(40 volts into the 36V one?)
The Ride-
A rebuilt Razor Electric Punk,
( with the folding collapsing still working to hopefully still fit into a suitcase)
stretched front end, suspentioned, racked back with a 12.5x2.25 three spoked wheel
Lengthened and widened rear wheel mount with a FREE Wheeled 10x35-4 with two extra spring shocks
replaced the 12V, 80W motor, still using stock mounting system, Tensionable drive belt
Waiting for a battery system-
installed for scare testing-
MY1016, 18V, 2700RPM, 150W, 10.9A
If 150W wasn't to BAD,
ON hand- ( using same mounting hole pattern)
MY1016, 24V, 2750RPM, 300W, 16.4A unite motor
MY1018, 24V, 2500RPM, 300W, 16.5A JX motor
So-
PLEASE let me know what you think about the battery and controller problem I have
NO! I don't want to BUY Li- anything right now
I've got all those NiMh's and a big box of Ni-Cads, ALL NEW needing to get used!
Just
Asking