EU Group Buy *CLOSED* NEW MXUS3000W V3 TURBO!

[Darowi]

I have seen that there is interest in buying the MXUS 3000W hub motor in the other thread, so I started this one to progress into a possible new group buy. My location is Hannover, Germany and I could think about organizing an EU + Switzerland group buy. Let´s start a list.

Specs: (see threads here for better info)

MXUS 3000 Turbo (V3)

- 145mm aluminium stator
- temp sensor
- 3.000W to 6.000W
- 3T or 4T windings
- ~9,3kg
- 142mm dropout

upgrades to V2:

- 4mm² phase wires
- 38H bended magnet
- 6004 Bearing 20mm id on one side
- 20mm axle (partial)
- double hall sensors

Price if the goal of 20pcs is reached:

280€ all taxes (for EU members) and PayPal included

Shipping with DHL, insured: (10kg packet)
Germany: 8€
EU: 20€
Europe - EU: 35€
Worldwide: 49€

Production time: 1-2 weeks
Shipping time: ~4 weeks SEA SHIPPING!

Update 08.03:

The "bended magnets" are not yet produced, therefore there is no photo available. BUT we can have it in our batch of motors!
I have attached 2 photos: 1 unpainted V3 "Turbo" Cover, 1 painted standard cover

Update 21.03.:

I have realized that it will take some more time and have arranged it with MXUS.
But let´s finish the list end of march?! Shouldn´t we?

PARTICIPATION CLOSED - TIME TO PAY
(Last minute orders: PM)

Summary

Object:
MXUS3000 V3 Turbo Motor
1. 45H aluminum stator with 0.35mm silicon steel sheets
2. 4MM² cable
3. 38H “bended” magnets
4. 21X3T OR 4TX16 windings
5. XT150 connector for phase wire 11G
6. 3 + 2x6 pin wires, double hallsensors
7. KTY84-130 thermosensor installed, wired to GND and the 6th wire
8. 10G spoke holes

Prize:
280€ + shipping (see above)

Warranty:
MXUS will provide 2 years warranty for the motors. (test or use with Vbatt <= 48V

Prod. / shipping time:
about 6-7 weeks to you, insured and tracked


Directions:

1. Please send me a private message with following info:
Please use this Syntax only, questions separately via PM

Subject: MX3000

Message:
[Nick] - [PayPal Email] - [Full Name + Address] - [3T or 4T windings]

2. You will receive a PM from me containing my PayPal Account, my name, address and the amount for your location.

3. Please pay fast!

4. I will keep the payment list updated. After completion I will start the order.

5. Once I`ll receive the motors, I will send them out to you insured and tracked.

Thanks,
Daniel

UPDATE:
To speed up the order process and because of demand, I offer in addition to the motors:

1. Laced V3 ("bended" magnet version) motor in 26" or 24" or 17" moto rim = +35€
2. Kunteng Sine wave controller with 12 MOSFETs and capable of 60A = +105€
3. LCD3 Display Unit for Kunteng Controller = +35€
Due to shipping limitations I can only ad a few laced orders, therefore: first asked, first served!

Spring is here, let´s get this thing onto the boat soon, shouldn´t we?
Daniel

[Darowi]

MXUS 3000W Hub Motor EU group buy interest list (please quote and add your name and quantity)

1 - Darowi

[Craigh85]

1- CraigH85

[BoomerChomsi]

Thanks for starting up this groupbuy.

Any pictures of this motor? also dropout is 145mm right?

[Darowi]

142mm

[BoomerChomsi]

Waauww even better, thanks mate! any price direction yet if we will buy 20-25 pieces?

[Suggs]

Subject to price, put me down.

[atomek1000]

what do you mean by

38H bended magnet

Height of magnets in this 3000w model should be 45mm.

[madin88]

what do you mean by

38H bended magnet

Height of magnets in this 3000w model should be 45mm.

38H should be the grade or strength of the neodymium magnets.
Darowi, from where do you have the info that MXUS now uses bended magnets? would be a nice little improvement

[Darowi]

MXUS gave me the information that the magnets have been changed from 35 to 38H strengh, bended.

[gabriel83]

+1Gabriel83

[madin88]

MXUS gave me the information that the magnets have been changed from 35 to 38H strengh, bended.

normally the Magnets should have been already 38H before, but rectangular.
Darowi, could you ask for a pic of the rotor for confirmation?

btw: it may be worth to wait for the V3 version with M16 axle.

[Darowi]

Yes, I already asked for photos and will ask for M16 also.
Will M16 still fit normal dropouts?

[madin88]

Yes, I already asked for photos and will ask for M16 also.
Will M16 still fit normal dropouts?

depends on the frame, but for 99% i would say YES it will fit as both have 10mm wide flat part.
the only thing that might be a problem is adjusting the disc brake caliper properly, but compared to M14 the center of the axle only would be 1mm farther away what should be in the room for adjustments - and if not it should be easy to fix.

[cwah]

+1 for sure.

I may buy a second motor as spare if I can benefit a discount with 2 motors.

[Relanium]

1 - Relanium

(thanks for doing this!)

[Darowi]

1- Darowi
1- CraigH85
1- BoomerChomsi ?
1- Suggs
1- Gabriel83
1- cwah
1- Relanium
----------------------------
7

[Shaggy2Dope]

+1 - Shaggy2Dope

[jase1979]

1 jase1979 please.

[Sr.Agaporni]

+1 Sr.Agaporni

Thanks!

[Darowi]

1- Darowi
1- CraigH85
1- BoomerChomsi ?
1- Suggs
1- Gabriel83
1- cwah
1- Relanium
1- Shaggy2Dope
1- jase1979
1- Sr.Agaporni

------------------------
10 = half time!

[liamcaff]

1 - liamcaff pretty please

[arcticfly]

1- arcticfly

[Racer_X]

1 - Racer_X (4T windings)

[Polos]

1 - Polos