matt912836
100 W
Started as a Mongoose Pro Wing
Steel rear triangle is a plus for a hub
Many iterations later...
120mm suntour fork
Fox Float RP2 rear shock with longer eye-eye
58v20ah echo battery
Bmx riser cruiser bars
Bmx pegs bolted through bottom bracket
Shunt modded 48v 45a 1500w controller w. 60/100/120% speed settings and regen/eabs
16x3 rear hub motor with angled vent holes +upgraded phases
Two torque arms
20x3 front tire alexrims dx32 160mm disc brake
2x nes-350-27 meanwells in series set to 29v for a simple 58v12a charger.
2x 20w led lights
Full twist throttle w/ key and led voltage readout
Each 4ah battery can be charged at 4ah for one hr recharge, and they also have 2ah batteries which also carge at 4ah so that means these cells take a 2c charge rate set by default with oem charger. so 12a on 20ah is light on these batteries. Should be able to charge @ 30-40a for a > 1hr charge too bad 58v12a is already at the limits of your average 120v house outlet.
~30mph top speed on 120%
Rides like a dream and pulls like a train for just ~2000w peak thanks to low diameter hub
Never had a flat thanks to 3inch tires.
Hub and controller Stay stone cold in stop and go nyc traffic. Barely warm after a full WOT run around manhattan. range is very impressive given the wattage of controller. Thanks to the low diameter hub you get way more torque while the amps you draw drops a lot quicker compared to 26inch wheel. Flys up hills like they dont exist.
~130lb rider weight definitely helps with performance
Really want to push the limits of this hub. Thought this controller would definitely make it hot but ive yet to make this hub warm/hot to the touch.
Only upgrade in mind is an upgrade to a 96v1500w controller, add another 4ah and wire it 3p2s for 116v12ah
That would probably need a longer swing arm... triangle is steel so weldable.. i also have the original swing arm from the heavy steel scooter it came off of....possible to weld it to the triangle as an extension?
Comments/questions/suggestions
Steel rear triangle is a plus for a hub
Many iterations later...
120mm suntour fork
Fox Float RP2 rear shock with longer eye-eye
58v20ah echo battery
Bmx riser cruiser bars
Bmx pegs bolted through bottom bracket
Shunt modded 48v 45a 1500w controller w. 60/100/120% speed settings and regen/eabs
16x3 rear hub motor with angled vent holes +upgraded phases
Two torque arms
20x3 front tire alexrims dx32 160mm disc brake
2x nes-350-27 meanwells in series set to 29v for a simple 58v12a charger.
2x 20w led lights
Full twist throttle w/ key and led voltage readout
Each 4ah battery can be charged at 4ah for one hr recharge, and they also have 2ah batteries which also carge at 4ah so that means these cells take a 2c charge rate set by default with oem charger. so 12a on 20ah is light on these batteries. Should be able to charge @ 30-40a for a > 1hr charge too bad 58v12a is already at the limits of your average 120v house outlet.
~30mph top speed on 120%
Rides like a dream and pulls like a train for just ~2000w peak thanks to low diameter hub
Never had a flat thanks to 3inch tires.
Hub and controller Stay stone cold in stop and go nyc traffic. Barely warm after a full WOT run around manhattan. range is very impressive given the wattage of controller. Thanks to the low diameter hub you get way more torque while the amps you draw drops a lot quicker compared to 26inch wheel. Flys up hills like they dont exist.
~130lb rider weight definitely helps with performance
Really want to push the limits of this hub. Thought this controller would definitely make it hot but ive yet to make this hub warm/hot to the touch.
Only upgrade in mind is an upgrade to a 96v1500w controller, add another 4ah and wire it 3p2s for 116v12ah
That would probably need a longer swing arm... triangle is steel so weldable.. i also have the original swing arm from the heavy steel scooter it came off of....possible to weld it to the triangle as an extension?
Comments/questions/suggestions