Votol EM-100 & EM-150 controllers

General Discussion about electric vehicles.
Transerfer   10 mW

10 mW
Posts: 33
Joined: May 31 2022 3:38am

Re: Votol EM-100 & EM-150 controllers

Post by Transerfer » Jul 29 2022 2:42pm

BareKuda wrote:
Jul 29 2022 7:53am
Transerfer wrote:
Jul 28 2022 12:15pm
BareKuda wrote:
Jul 26 2022 2:24am
Transerfer wrote:
Jul 25 2022 9:07am
How can I at least do a factory restore? Thanks!!
To do “factory reset” equivalent you need the original configuration file, unmodified. If you opened it, changed it and saved it under the same name, it might be corrupted.

Hello BareKuda! I struggled with this problem for two days and nothing happened. I am sending 2 screenshots, on the first one the full original "ini" of the controller file. On the second, what is loaded after recording. What is circled in red does not change in any way. Whatever values ​​I enter..
Do you have an idea what could be the problem? And what can I do to solve it? Thank you very much in advance!
The original file looks ok for page 1. Are you saying after you open that file and then “write param” it goes back to the second screenshot with 38a and 55v OVP?

If so then something is corrupted.

Post your orientation ini file and your current ini file here and ill try to make you a good file.
Yes, you are absolutely right, friend! And so it happens! After saving the original "ini" file and rebooting, what comes out is what is in the second screenshot.

What exactly can be damaged? Do you mean mechanical?

Do you mean send you the original? If yes, then I'm attaching it here!

Thank you
Attachments
Config.ini
(483 Bytes) Downloaded 19 times

MomentFD   10 µW

10 µW
Posts: 6
Joined: Jan 31 2022 1:47pm

Re: Votol EM-100 & EM-150 controllers

Post by MomentFD » Jul 30 2022 3:51pm

Setup: EM150-SP/2, QS 138 70h v3, only wired throttle, e-lock and CAN to computer up. Would like to jump sport mode always-on.

I'm preparing for the first road test, I have the minimum port assignments and harness connections but controller is default in H gear and the wheel spins on the stand. It spins somewhat quickly but any rear brake application stops it completely, and the bike has 0 wheel torque once I put it on the ground.
Could that be a phase wire/hall shift issue?
I'm looking for other settings that could affect this, it spins great forward gets to 50kph on stand with good motor noise.

I would like to connect my gear and sport selector since I'm reading I should try all this in sport, but I don't feel confident with all the different wiring/port settings out there. I'm on an EM-150SP/2 and it has the large, 23 pin connector.
Attachments
Config 072722 works wheel up.ini
(479 Bytes) Downloaded 9 times

User avatar
BareKuda   100 W

100 W
Posts: 230
Joined: Oct 26 2021 1:36am

Re: Votol EM-100 & EM-150 controllers

Post by BareKuda » Jul 30 2022 9:53pm

Transerfer wrote:
Jul 29 2022 2:42pm

Do you mean send you the original? If yes, then I'm attaching it here!

Thank you
I used your file to get all the settings to enter into a copy of my file which is my current file. i can see some numbers inside still don't match but maybe it will allow you to make change.

try this file and see if your controller will accept them and allow you to change settings and write param.

IF it works but not your ideal settings, go ahead and change these settings to match your motor-controller.
Attachments
ConfigEM50-72v.ini
(484 Bytes) Downloaded 12 times

Transerfer   10 mW

10 mW
Posts: 33
Joined: May 31 2022 3:38am

Re: Votol EM-100 & EM-150 controllers

Post by Transerfer » Jul 31 2022 3:22am

BareKuda wrote:
Jul 30 2022 9:53pm
Transerfer wrote:
Jul 29 2022 2:42pm

Do you mean send you the original? If yes, then I'm attaching it here!

Thank you
I used your file to get all the settings to enter into a copy of my file which is my current file. i can see some numbers inside still don't match but maybe it will allow you to make change.

try this file and see if your controller will accept them and allow you to change settings and write param.

IF it works but not your ideal settings, go ahead and change these settings to match your motor-controller.
Thanks a lot, friend! I'll try it today and I'll be sure to post the results.

MomentFD   10 µW

10 µW
Posts: 6
Joined: Jan 31 2022 1:47pm

Re: Votol EM-100 & EM-150 controllers

Post by MomentFD » Aug 01 2022 7:07pm

Got my EM-150SP/2 and QS 138 v3 running with a base config file and changing motor settings. Should be -60 hall shift and exchange phase blue-green if using the physical wiring shown in my previous post.

In general, are there areas of parameter tuning or operation in general to be cautious with? Basically things that could damage the controller/motor/battery? I already consider port settings like this but am curious about specific parameters.

I saw the post a while ago about the fire starting controller, possibly caused by disconnecting during high regen. Any pitfalls like this I want to be very aware of.

Thanks all & cheers!
Attachments
C2 080122 spinning - change motor settings park port.ini
(493 Bytes) Downloaded 10 times

laarsn   1 µW

1 µW
Posts: 1
Joined: Aug 02 2022 11:26pm

Re: Votol EM-100 & EM-150 controllers

Post by laarsn » Aug 02 2022 11:36pm

Hi guys, i'm looking for complete config file to program VOTOL EM-150SP/2 with stock Sur-Ron motor. Any help would be appreciate!

laarSn

User avatar
BareKuda   100 W

100 W
Posts: 230
Joined: Oct 26 2021 1:36am

Re: Votol EM-100 & EM-150 controllers

Post by BareKuda » Aug 03 2022 5:23am

MomentFD wrote:
Aug 01 2022 7:07pm

In general, are there areas of parameter tuning or operation in general to be cautious with? Basically things that could damage the controller/motor/battery? I already consider port settings like this but am curious about specific parameters.
That last configuration file looks like a good starting point. I see it has 7000 rpm HDC so that is well into flux weakening.

The HDC rpm should be set at the fastest it can realistically run under load. If 7000 is 100 mph and 200a then that wont work. But if the motor and controller can handle the load then you can tweak HDC rpm and flux weakening (including compensation %) until it give best results.

Unfortunately I haven’t played with that much because my 500w motor needs 1500w to cruise at 25 mph which it can do at base speed.

Just make small changes and road test between changes. I took my laptop with me so it was easy. If you have to stop and connect the laptop each time it will be arduous but thats what it takes,

HelloItsMeJosh   1 µW

1 µW
Posts: 1
Joined: Aug 05 2022 1:01pm

Re: Votol EM-100 & EM-150 controllers

Post by HelloItsMeJosh » Aug 05 2022 1:28pm

Hello there, can any of you guys help a dude out and send over the 2.33 version of the software please?

User avatar
BareKuda   100 W

100 W
Posts: 230
Joined: Oct 26 2021 1:36am

Re: Votol EM-100 & EM-150 controllers

Post by BareKuda » Aug 06 2022 6:51am

HelloItsMeJosh wrote:
Aug 05 2022 1:28pm
Hello there, can any of you guys help a dude out and send over the 2.33 version of the software please?
http://www.siaecosys.com/upfile/202101 ... 865893.zip

Paulflieg   100 W

100 W
Posts: 119
Joined: Jan 11 2019 10:30am

Re: Votol EM-100 & EM-150 controllers

Post by Paulflieg » Aug 06 2022 10:05am

BareKuda wrote:
Aug 06 2022 6:51am
HelloItsMeJosh wrote:
Aug 05 2022 1:28pm
Hello there, can any of you guys help a dude out and send over the 2.33 version of the software please?
http://www.siaecosys.com/upfile/202101 ... 865893.zip
This is just the debugging software, nothing more!

User avatar
BareKuda   100 W

100 W
Posts: 230
Joined: Oct 26 2021 1:36am

Re: Votol EM-100 & EM-150 controllers

Post by BareKuda » Aug 06 2022 1:14pm

Paulflieg wrote:
Aug 06 2022 10:05am
BareKuda wrote:
Aug 06 2022 6:51am
HelloItsMeJosh wrote:
Aug 05 2022 1:28pm
Hello there, can any of you guys help a dude out and send over the 2.33 version of the software please?
http://www.siaecosys.com/upfile/202101 ... 865893.zip
This is just the debugging software, nothing more!
What were you expecting? The STM32 firmware? Do you think he wants that? Go ahead and post it here. Lol

Paulflieg   100 W

100 W
Posts: 119
Joined: Jan 11 2019 10:30am

Re: Votol EM-100 & EM-150 controllers

Post by Paulflieg » Aug 06 2022 3:52pm

BareKuda wrote:
Aug 06 2022 1:14pm
Paulflieg wrote:
Aug 06 2022 10:05am
BareKuda wrote:
Aug 06 2022 6:51am
HelloItsMeJosh wrote:
Aug 05 2022 1:28pm
Hello there, can any of you guys help a dude out and send over the 2.33 version of the software please?
http://www.siaecosys.com/upfile/202101 ... 865893.zip
This is just the debugging software, nothing more!
What were you expecting? The STM32 firmware? Do you think he wants that? Go ahead and post it here. Lol
Nothing, yes, yes, I would very much like to do......

User avatar
BareKuda   100 W

100 W
Posts: 230
Joined: Oct 26 2021 1:36am

Re: Votol EM-100 & EM-150 controllers

Post by BareKuda » Aug 07 2022 3:12am

Paulflieg wrote:
Aug 06 2022 3:52pm
BareKuda wrote:
Aug 06 2022 1:14pm
Paulflieg wrote:
Aug 06 2022 10:05am
This is just the debugging software, nothing more!
What were you expecting? The STM32 firmware? Do you think he wants that? Go ahead and post it here. Lol
Nothing, yes, yes, I would very much like to do......
Go ahead, if you can, but you cant. Flashing the STM32 requires special equipment and the file. Most people have no idea how to do it and will only brick their controller. But go ahead and post the links to everything needed to do that..if you can. Lol

Transerfer   10 mW

10 mW
Posts: 33
Joined: May 31 2022 3:38am

Re: Votol EM-100 & EM-150 controllers

Post by Transerfer » Aug 07 2022 10:28am

BareKuda wrote:
Aug 06 2022 6:51am
HelloItsMeJosh wrote:
Aug 05 2022 1:28pm
Hello there, can any of you guys help a dude out and send over the 2.33 version of the software please?
http://www.siaecosys.com/upfile/202101 ... 865893.zip

Hi, friend! According to your config sent to me. Nothing. I spent several hours without success. The data circled in the screenshot is not recorded. No matter how much I tried, the readings after the reboot are like this ..
Attachments
2.jpg
2.jpg (147.45 KiB) Viewed 10 times

Post Reply