Looking for Bafang motor cable.

Looking for something? Need a special part, but can't find it online anywhere? Post what you need, maybe others will have it to sell.
Post Reply
alfgar   10 mW

10 mW
Posts: 25
Joined: Mar 18 2017 2:31pm

Looking for Bafang motor cable.

Post by alfgar » Aug 03 2022 6:48pm

Hi, I recently got a good deal a Rize Liberty e-bike with a 48v bafang G062. 750 watt hub motor that needs the cable replaced because it's ripped.

Not sure why but I cannot seem to find where to buy the motor cable. Found the following but it’s to short for me.

https://ebikes.ca/l1019-m.html

I would appreciate help in finding somewhere to buy a cable.

Side note: The seller told me it was a 750W but once apart, the hub is stamped 1000W. Not sure how to interpret that?


Thanks in advance
Attachments
S11.jpg
S11.jpg (181.37 KiB) Viewed 83 times
S22.jpg
S22.jpg (325.21 KiB) Viewed 83 times
S33.jpg
S33.jpg (223.8 KiB) Viewed 83 times
S44.jpg
S44.jpg (142.87 KiB) Viewed 83 times

TuomasK   10 mW

10 mW
Posts: 30
Joined: Aug 07 2020 2:32am

Re: Looking for Bafang motor cable.

Post by TuomasK » Aug 05 2022 4:01am

There is L1019 extension cable available from Grin too. Its 60cm in length so you can cut and use the length desired. https://ebikes.ca/l10-ext.html

I have bought L10 and other cables from e-bike technologies but Im based in EU.
https://www.e-bike-technologies.de/inde ... m-s-detail
Attachments
IMG_20220306_205242.jpg
IMG_20220306_205242.jpg (2.41 MiB) Viewed 53 times
IMG_20220306_153252.jpg
IMG_20220306_153252.jpg (3.16 MiB) Viewed 53 times

alfgar   10 mW

10 mW
Posts: 25
Joined: Mar 18 2017 2:31pm

Re: Looking for Bafang motor cable.

Post by alfgar » Aug 05 2022 8:45pm

Thank you very much. Really appreciate it. Waiting on anther source but I believe I will end up getting this one after all.

Two questions if I may.

1 - was it tight to pull through the shaft? Any major issues?

2 - in your pic, it looks like the small green and yellow wires are reverse from mine? I haven't really snipped and looked closely at mine in detail yet. But in the pics, they looked reversed.

thanks again.

TuomasK   10 mW

10 mW
Posts: 30
Joined: Aug 07 2020 2:32am

Re: Looking for Bafang motor cable.

Post by TuomasK » Aug 06 2022 3:27am

alfgar wrote:
Aug 05 2022 8:45pm
Thank you very much. Really appreciate it. Waiting on anther source but I believe I will end up getting this one after all.

Two questions if I may.

1 - was it tight to pull through the shaft? Any major issues?

2 - in your pic, it looks like the small green and yellow wires are reverse from mine? I haven't really snipped and looked closely at mine in detail yet. But in the pics, they looked reversed.

thanks again.
1. Not too tight. In fact I also added two thin extra wires for temp sensor.
2. I've seen the motor cable colors or mapping may vary. Best to check pcb tab to connector pin

alfgar   10 mW

10 mW
Posts: 25
Joined: Mar 18 2017 2:31pm

Re: Looking for Bafang motor cable.

Post by alfgar » Aug 06 2022 11:11am

great. thanks again/

Post Reply