Programming APT AE96600 controller (UPDATE: don't buy..)

Get all your technical information about electric bikes here.
larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » Nov 19 2018 11:56am

If you sent the new evdrive program then i guess it won't make any difference for ammo1.. But if you sent something more interesting then please share with us too :D
Ride on :D

Ammo1   1 mW

1 mW
Posts: 14
Joined: Nov 16 2018 1:10am

Re: Programming APT AE96600 controller

Post by Ammo1 » Nov 19 2018 1:32pm

entire torque controls and alot of others maybe it wont but expect it to make a difference and yes is confirmed by the hall test is running with a qs273 8kw is barely getting warm at all but has hit the motor oh that was was thinking it could be in f instead of c but not sure really as of yet it should be warm if im getting a 140c cutoff warning but then internal temps can be alot different

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » Nov 19 2018 1:42pm

I guess the -105 deg hall setting was developed for a qs motor, is it the same as yours?

I am thinking it could be wrong since the hall test for your motor is around 60degrees but the general phase setting is -105degrees,
- what happens if you set this to 60degrees, does it run better or worse?

I also think that motor lock timeout and motor lock current could be increased to 60 seconds, 100% current in the protection screen. I guess the low threshold (28%) that's there now could trip protection.
Ride on :D

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » Dec 08 2018 4:50pm

I got a more complete manual from Advpower, it explains a lot but not all, i am still asking them for the flux weakening description. Parameters are set for hub motor in this manual so i will do some trials to see if i can change them to suit the mid drive motor.
Ride on :D

Bartosh   1 mW

1 mW
Posts: 17
Joined: May 10 2017 3:32pm

Re: Programming APT AE96600 controller

Post by Bartosh » Jan 20 2019 5:46pm

Hey larsb, any luck running qs 138 mid drive with flux? BTW what's your opinion on the controller so far?

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » Feb 09 2019 1:44pm

My bike is still broken so no trials done yet..

I will soon start a new thread on the battery build :D
Ride on :D

Ammo1   1 mW

1 mW
Posts: 14
Joined: Nov 16 2018 1:10am

Re: Programming APT AE96600 controller

Post by Ammo1 » Apr 01 2019 9:38am

larsb wrote:
Feb 09 2019 1:44pm
My bike is still broken so no trials done yet..

I will soon start a new thread on the battery build :D
hi larsb sorry to hear about the bike . my house actually went on fire i lost pretty much everything except my bike but all my batteries chargers ect gone thats the main reason i havent been online . whats wrong with your bike ? and whats the plan for the battery ? i could probably help if you need any tips i was sort of the battery guy until the fire lost around 6 or 7 thousand euros worth of 18650s and lipos but going to start collecting them again as soon as by bills are paid .

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » Apr 02 2019 5:02am

I feel for you! My battery issues in relation to that is quite simple..

I crashed the bike and battery pack so i am building a new pack with automotive cells from volvo s60 hybrid. It's soon finished - i hope! :D
Ride on :D

Ammo1   1 mW

1 mW
Posts: 14
Joined: Nov 16 2018 1:10am

Re: Programming APT AE96600 controller

Post by Ammo1 » Apr 14 2019 4:49pm

Nice well besides the crash and had a friend build his with leaf cells there good too and thanks starting to get my love for electronics back slowly .

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 06 2019 4:57am

Good day I have a motorcycle with a 5000 watt motor wheel, and an APT 96600 controller, but it starts to shut down after 5-10 minutes of driving. Controller to the touch, about 40 degrees, who knows the reason for the shutdown?

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 10 2019 6:32am

Here are my factory settings can someone tell me?

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » May 10 2019 11:00am

If controller shuts down then there must be an error code, (what is it?)
Ride on :D

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 12 2019 6:02am

The LEDs on the controller do not flash, they are lit constantly.
Interestingly the motor is almost cold
Last edited by SergeyNikulochkin on May 12 2019 6:29am, edited 1 time in total.

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 12 2019 6:28am

And the controller is heated to 40-45 degrees Celsius. Can in settings parameters of temperature of the controller in Fahrenheit and not in Celsius are specified?

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 12 2019 11:51am

This error is shown by the controller
Оver iac

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » May 13 2019 3:30pm

I guess it's a cutout due to controller error that cannot be solved easily. Over IAC is probably that there are current spikes above the set protection values. If you have long wires from battery to the controller or they are not equal lengths or are not side by side then you can try to improve these three things.
Ride on :D

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » May 13 2019 3:34pm

Bartosh wrote:
Jan 20 2019 5:46pm
Hey larsb, any luck running qs 138 mid drive with flux? BTW what's your opinion on the controller so far?
I am driving again, new batteries and the APT, so far only some runs. I sometimes get cutouts at close to 300A battery / 600A phase current so i guess that this is close to the limit of the AE96600 with my setup.
Ride on :D

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 15 2019 8:09am

In the settings window "Protection" I increased the parameter is not 28% and 40%, will help me to reduce the appearance of errors and disable the controller? And wouldn't that ruin the controller?

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » May 15 2019 12:12pm

Which parameter? (please post screenshot)
Ride on :D

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 15 2019 12:21pm

you can't insert an attachment

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » May 15 2019 12:44pm

You can, under attachments.
image.png
Ride on :D

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 15 2019 12:48pm

I do so and click attachments, open the file, it is loaded, but not inserted with the message

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 15 2019 12:51pm

не получается даже при перетаскивании файла, могу попробовать рисунок на почту скинуть, если скажете свой адрес

SergeyNikulochkin   100 mW

100 mW
Posts: 41
Joined: May 06 2019 4:35am

Re: Programming APT AE96600 controller

Post by SergeyNikulochkin » May 15 2019 1:07pm

On the first page there is a picture of this window "Protection". Left column 4 at the top of the line "Motor loc iac" and set the value to 28. I tried to lift it but more than 30 does not rise. Perhaps it depends on the parameter above "Heavy Load iac", and it should also be raised above?

larsb   10 kW

10 kW
Posts: 991
Joined: Dec 10 2014 5:12am
Location: Gothenburg, Sweden

Re: Programming APT AE96600 controller

Post by larsb » May 15 2019 2:59pm

You are correct. This is locked at max 30% in program.. hmm
Last edited by larsb on Jun 02 2019 1:15am, edited 2 times in total.
Ride on :D

Post Reply