Actually i think i can, with this temperature controller conected to brake sensor wire https://www.ebay.com/itm/323263962394Elinx said:You can't use the temperature sensor with stock firmware. Only the Open source firmware can handle this protection.
marcoq said:Hello guys.
I have solved some bugs recently found in my firmware and I will soon release a new version of the configurator [ver. 0.3.8] that will allow you to select my code or Ackmaniac's code by a checkbox. :thumb:
Oh..., you choose another hardware solution than the LM35 sensor for OSFsp1n4d0 said:....
Actually i think i can, ............
Hello Marcoq, thanks for your notification. I look towards to it.marcoq said:.... I will soon release a new version of the configurator [ver. 0.3.8] that will allow you to select my code or Ackmaniac's code .....
phm2000 said:.....
Ackmaniac firmware, .....
...
no more assistance.
...
I put factory firmware ..... no assistance.
......
What's the problem ?....
Elinx said:phm2000 said:.....
Ackmaniac firmware, .....
...
no more assistance.
...
I put factory firmware ..... no assistance.
......
What's the problem ?....
Maybe the speedsensor is rotated or too close to magnet?
Elinx said:Hello Marcoq, thanks for your notification. I look towards to it.marcoq said:.... I will soon release a new version of the configurator [ver. 0.3.8] that will allow you to select my code or Ackmaniac's code .....
You mean that there will be a choice for controlling the battery current or motor current.
I hope too it is based on the last OSF v. 20 from Buba.
phm2000 said:Hi
I just install a new TSDZ2 750W 48V with VLCD5, with Ackmaniac firmware, all seems to be fine (thanks a lot Marocq and Ackmaniac)
But and after 20km, no more assistance.
I put factory firmware again and try, no assistance.
But
Walk assist is OK
Throttle is OK
On hidden menu, I find : RE is at 0 and RE1 is at 0
What's the problem ?
Is there a torque sensor failure or anything else ?
Thanks
Badmotor said:phm2000 said:Hi
I just install a new TSDZ2 750W 48V with VLCD5, with Ackmaniac firmware, all seems to be fine (thanks a lot Marocq and Ackmaniac)
But and after 20km, no more assistance.
I put factory firmware again and try, no assistance.
But
Walk assist is OK
Throttle is OK
On hidden menu, I find : RE is at 0 and RE1 is at 0
What's the problem ?
Is there a torque sensor failure or anything else ?
Thanks
When you put stock firmware, did you change the openbyte to 28 ?
Thanks for reporting back.marcoq said:.......... however I am also working for migrate buba's firmware to OEM displays.... but I will need some time.
phm2000 said:Badmotor said:phm2000 said:Hi
I just install a new TSDZ2 750W 48V with VLCD5, with Ackmaniac firmware, all seems to be fine (thanks a lot Marocq and Ackmaniac)
But and after 20km, no more assistance.
I put factory firmware again and try, no assistance.
But
Walk assist is OK
Throttle is OK
On hidden menu, I find : RE is at 0 and RE1 is at 0
What's the problem ?
Is there a torque sensor failure or anything else ?
Thanks
When you put stock firmware, did you change the openbyte to 28 ?
I saved stock firmware and there's already 28 on openbyte
zappan said:phm2000 said:Badmotor said:phm2000 said:Hi
I just install a new TSDZ2 750W 48V with VLCD5, with Ackmaniac firmware, all seems to be fine (thanks a lot Marocq and Ackmaniac)
But and after 20km, no more assistance.
I put factory firmware again and try, no assistance.
But
Walk assist is OK
Throttle is OK
On hidden menu, I find : RE is at 0 and RE1 is at 0
What's the problem ?
Is there a torque sensor failure or anything else ?
Thanks
When you put stock firmware, did you change the openbyte to 28 ?
I saved stock firmware and there's already 28 on openbyte
I am following this discussion and have never had the problem in restoring the original SW, but for knowledge I wonder where it configures openbyte to 28? I haven't seen it in any guide.
Already solved or minimised this issue, changed all the values of the motor power boost to zero, now it only takes some time to disengage the motor in assist level 4, witch i rarely use, all other assist levels are fine.sp1n4d0 said:Installed this firmware and a temperature sensor, it is running fine except when I stop pedaling the motor takes mutch time to stop compared to stock firmware, this is grinding my gears and lost the natural feeling.
there is any option on the java configuration to make motor stop faster?
Elinx said:v. 19C is the latest.danielson said:I'm using the V19 and 3.7. ........
Version 19A and B has this stil this bug.
So, if you want to prevent the same problem, check thoroughly if you have the "C" version of the firmware.
The java-configurator v3.7 is the same for all.
In that case I hope marcoq is reading these posts too and can find the reason, because this could be unexpected but dangerous behavior with touring.wpenner said:............I'm on V19c and had this happen twice now. ..........Elinx said:.....
v. 19C is the latest.
Version 19A and B has this stil this bug...........
wpenner said:I finally installed my silicone heat transfer pads today. It took two pads $4.44US. 3 layers at some points. I’ll find out tomorrow if they work as my bike usually hits throttle reduction temperature on last 5 minutes of my ride home.
ABB77FD1-5ECC-4188-A953-542379BEEFBC.jpeg
1028174E-677A-4DF7-9087-0F77C6F73D77.jpeg
bluesoc said:wpenner said:I finally installed my silicone heat transfer pads today. It took two pads $4.44US. 3 layers at some points. I’ll find out tomorrow if they work as my bike usually hits throttle reduction temperature on last 5 minutes of my ride home.
ABB77FD1-5ECC-4188-A953-542379BEEFBC.jpeg
1028174E-677A-4DF7-9087-0F77C6F73D77.jpeg
Any update on how the silicone pads are working?
Also, would you mind posting where you got the pads?
wpenner said:bluesoc said:wpenner said:I finally installed my silicone heat transfer pads today. It took two pads $4.44US. 3 layers at some points. I’ll find out tomorrow if they work as my bike usually hits throttle reduction temperature on last 5 minutes of my ride home.
ABB77FD1-5ECC-4188-A953-542379BEEFBC.jpeg
1028174E-677A-4DF7-9087-0F77C6F73D77.jpeg
Any update on how the silicone pads are working?
Also, would you mind posting where you got the pads?
Yes, they are definitely doing something as my bike is no longer reducing power at the end of my commute. I used 2 pads. You might want to order 3 in case you mess up cutting them to shape. https://www.ebay.ca/itm/100mmx100mmx2mm-Silicone-Pad-Heat-Sink-Heatsink-Thermal-Conductive-Cooling-f/264310728713?hash=item3d8a25a809:gvUAAOSw2KlczvhZ
wpenner said:Elinx said:v. 19C is the latest.danielson said:I'm using the V19 and 3.7. ........
Version 19A and B has this stil this bug.
So, if you want to prevent the same problem, check thoroughly if you have the "C" version of the firmware.
The java-configurator v3.7 is the same for all.
I'm on V19c and had this happen twice now. Motor was still cool and not anywhere near temperature limit. Motor kept pushing me even though i stopped peddling. Speedometer was locked at 13.7km/h on the screen. Up and down buttons change assist level on screen but motor kept pushing. Holding down power button for three seconds stopped it.
bluesoc said:wpenner said:bluesoc said:wpenner said:I finally installed my silicone heat transfer pads today. It took two pads $4.44US. 3 layers at some points. I’ll find out tomorrow if they work as my bike usually hits throttle reduction temperature on last 5 minutes of my ride home.
ABB77FD1-5ECC-4188-A953-542379BEEFBC.jpeg
1028174E-677A-4DF7-9087-0F77C6F73D77.jpeg
Any update on how the silicone pads are working?
Also, would you mind posting where you got the pads?
Yes, they are definitely doing something as my bike is no longer reducing power at the end of my commute. I used 2 pads. You might want to order 3 in case you mess up cutting them to shape. https://www.ebay.ca/itm/100mmx100mmx2mm-Silicone-Pad-Heat-Sink-Heatsink-Thermal-Conductive-Cooling-f/264310728713?hash=item3d8a25a809:gvUAAOSw2KlczvhZ
Appreciate it! I have a tsdz2 on the way with a temp sensor, so perhaps I'll be able to get some concrete numbers for how well they work.
If you use VCLD5 or VCLD6 it will not display the current value of the temperature sensor. It will just let you know when you have reached the temperature thresholds that you have set.