eZip-iZip-Currie parts-n-such

I thought it would be handy to consolidate my eZip parts finds in one place.

40 Amp fuses for the RMB battery packs - 5 for $1 & shipping
Big shipping discount on multiple purchases!
Just click on pictures to go to Link.


36V controller with proper connectors - plug-n-play
Will lose PAS function - $37.50


ACS Southpaw LHS 1/2 x 1/8 x 16T Freewheel - $13.93
Easy 25% speed upgrade for eZips and many iZips! and others?


DNP Epoch 7spd 28-30-32 to 11T Freewheel - $34
Upgrades EZip w/44T Front Sprocket to near 30mph pedal assist (90 crank rpm) 20mph (60 crank rpm)

More sizes - 11- 28,30,32,34T - $32

72 CUSTOM LENGTH STAINLESS 13G SPOKES - $26 + $5 shipping
18-260mm & 18-258mm Spokes required for eZip rear wheel, 36-260mm for front.

150 13g Nipples

NEW!
9,11,13T Motor Sprocket Upgrade, (Currie, eZip, iZip) - $18 includes shipping
Plug-n-Play - except you will need longer chain


Good fit, good alignment, just lengthen chain and all set to go!
OEM eZip top speed @24V w/9T sprocket = 15mph.
15mph / 9T x 13T = 21.66mph (20mph USA "legal" - reasonable expectation)

eZip Rear Brake Pads - $5.95
Most notably, the older eZips require a "deep" brake pad for the rear wheel ... this work nicely!




My1018z 24V 450w motor - $99



7s - Tenergy Intelligent 2A Charger for 25.9V 7S Li-ion / Li-Polymer Battery Pack - $23.99
Bulk charger with "safety charging algorithms"
Great budget item but 4.2V per bank - not a balancing charger!
Gotta rip one open and try to trim voltage ... will report.

Update! - Simple voltage trimming method!

Other Tenergy chargers should have similar circuits.




10s - Tenergy Smart Charger for 37V 10-Cell 2A Li-ion/LIPO Battery Pack w/ Tamiya - $18.49
Bulk charger with "safety charging algorithms"
Special price w/Tamiya! Add your own connector.



eZip Trailz parts - In Stock! .... mostly ...


Much more here - non-eZip specific parts - eBike Toolbox bargains

Just click on pictures to go to Link.

Freewheel adapters for the Currie gear reduction motors are now available!
13, 14 an 15T freewheel compatible!
11mm ID w/4mm keyway ... Less than $17 !

Also,
Now available,
Adapters for 16T and larger freewheels! ... Less than $17 !

Staton-inc

Ordering up both and will report ... likely ... within a week!

JST-XH 2S-8S Battery Balance Board Adapter - for iMax B8+ and others

- $1.79 +$1.99 shipping .99 per additional


4 x 7s Balance cable
- $6.59 w/$1.74 shipping


2 x 8s Balance cable
- $4.99 w/ $1.74 shipping

10pcs JST-XH 8S 30cm Lipo Balance Wire Extension Charged Cable Lead Cord for RC
- $11.88

Tenergy Intelligent 2A Charger for 25.9V 7S Li-ion / Li-Polymer Battery Pack -- Anderson Connector - $14.95
Unbelievable price!
Great for 25.9V Li-ion, as 24V SLA replacement.



10pcs Balance Wire Extension 30cm - 3s, 4s, 5s, 6s, 7s, 8s, 10s, 12s!... $4-$14 w/free ship
They appear to be silicone?



NEW sizes!
8T/9T/11T/13T Motor Sprocket Upgrade, (Currie, eZip, iZip) - $18 includes shipping
Plug-n-Play - except you will need longer chain


Good fit, good alignment, just lengthen chain and all set to go!
OEM eZip top speed @24V w/9T sprocket = 15mph.
15mph / 9T x 13T = 21.66mph (20mph USA "legal" - reasonable expectation)

OEM parts at reasonable shipping rates.
Most important!
Most items are "in stock"!

eZip Electric Bike Parts
IZIP Electric Bike Parts
Currie Parts

Staton-inc.com has the 22T, but that is only a 10% reduction.

- $14.38
You might want to wait ...
I just took a ride in the cold and suffered a 2-3mph speed handicap.

Not sure if will fit ... might be too large of a diameter ...
But possible to put together a 27T.
$17.95 + $15.95 = $33.90
& =

On\off\on Battery Switch 30A 250V
Came as momentary, Disassemble and remove 2 springs for eZip use
Keep level - to prevent contact movement. Must be repositioned if upset from original position.
Dull knife or small screwdriver, pry alternately on each side of switch (next to rocker pin) to lift button.
lift out the 2 springs.
Push button back in till snaps in place
(Momentary position could be used in a precharge resistor application )

- 2-pcs $4.40 replaced "stiff" switch
UPDATE = Labeled "20A"!
Better price - same item? - 2 for $1.33

Limited Availability 5x 30A - $5 picture shows "30A"

YIYUN YK31C 24-36V compatible controller 28A
Requires connectors adapted!

- ±$12 I run 25.9V (20mph) & 33.3V (25mph Turbo).

eZIP Electric Bike 36 Hole 3/8'' Axle Double Threaded Rear Hub
Appears threaded "properly" - other replacements had poor thread job!

- $29.99 delivered Not purchased yet

13 Tooth 11mm Bore Sprocket for 1/2"x1/8" Bicycle Chain
Direct replacement for oem 9T (requires 2T longer chain)
+20mph@24V w/XYD-16 motor,
++20mph@24V w/M1018z motor
+++20mph@25.9V - Larger chainring or Epoch 11T rear cog recommended ... if you want to pedal assist ...

Now <$10 delivered!

Shopping, from Australia, is excessive but same for multiple of item.

MY1016 Brush Assembly might fit MY1018Z and XYD-16 but compare pictures to yours



MY1018z

Bargain prices on 9T and 13T motor sprockets for MY1016z motor.

Confirmed compatible with MY1018Z and XYD-16 motors

< $6 delivered

< $7 delivered

DrkAngel said:

YIYUN YK31C 24-36V compatible controller 28A
Requires connectors adapted!

- ±$12 I run 25.9V (20mph) & 33.3V (25mph Turbo).

Click to expand...

Just installed a Yi-Yun YK31c 24V 500w controller on another eZip.
Decided to test voltage limits:
Worked right past 50.4V. (44.4V fully charged).
Stopped testing at 50.7V ... 50V caps!

Might replace with 63V caps ... picked them up last Winter.

Very versatile controller!
And cheap enough to keep a cople spares handy.

No PAS function
Adds:
key lock option;
full voltage brake light output;
charging port (possibly disables accidental use while charger connected??)

16T - 18T - 20T ACS Crossfire LHS (Left Hand Screw) freewheels - $17.59



Direct replacement for the crappy eZip - iZip motor side freewheels, without the external removal tangs that required alignment modifications!

9T - 11T - 13T sprockets available , for the MY1018z, MY1016Z3, XYD-16
Sprockets $14.95

Same page for the 4mm key - $ .95

Shipped from USA
Shipping $ unknown

does the MY1016 Brush Assembly listed in this thread comes with the 4 springs that are located in the brush blocks?
I asked on the site that is selling the assembly but I haven't got any reply as yet so I am asking here if someone knows.

11mm ID >> 30mm 13T - 14T - 15T Freewheel adapter <$17
For 11mm shaft w/4mm key

Now Alloy version available!

Compatible with
MY1018z - 250-450w motor
XYD-16 - 250-450w motor
MY1016z3 - 350w motor
GNG BB Drive

- $16.95

Steel version available ... check below description.

I have the same controller at 36V. Which wire is used to switch "On"? Connected to a 41.6V psu/charger; charging port, [blue - red] shows the same voltage. Do you just jumper the [black - red]?

DrkAngel said:

DrkAngel said:

YIYUN YK31C 24-36V compatible controller 28A
Requires connectors adapted!

- ±$12 I run 25.9V (20mph) & 33.3V (25mph Turbo).

Click to expand...

Just installed a Yi-Yun YK31c 24V 500w controller on another eZip.
Decided to test voltage limits:
Worked right past 50.4V. (44.4V fully charged).
Stopped testing at 50.7V ... 50V caps!

Might replace with 63V caps ... picked them up last Winter.

Very versatile controller!
And cheap enough to keep a cople spares handy.

No PAS function
Adds:
key lock option;
full voltage brake light output;
charging port (possibly disables accidental use while charger connected??)

Click to expand...

YK31C Brush controller connection pin out



1. Throttle
2. Voltage monitor
3. Charging port
4. Key - power on
5. Brake disconnect
6. Brake light
7. Motor - power out
8. Battery - power in

.

thanks for putting this all together. I just got 4 ebikes for $300, gonna fix them all up and sell 2 of them and keep the lighter aluminum ones.